Raphaël Furnémont
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Raphaël Furnémont has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Bram Vanderborght
Brubotics, Vrije Universiteit Brussel and Imec, Elsene, Belgium
10 shared publications - Tom Verstraten
Robotics and Multibody Mechanics Research Group, Vrije Universiteit Brussel, Brussels, Belgium
10 shared publications - Dirk J. Lefeber
Department of Human Genetics, Radboud University Medical Center, Nijmegen, Netherlands
6 shared publications - Amin Khorasani
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
5 shared publications - Muhammad Usman
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
5 shared publications - Greet Van de Perre
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
4 shared publications
Latest Publications
- Open Access
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129787-129802
Cobots Designed for Strength, Not Stiffness
Conventional industrial robots are designed to be as stiff as possible to ensure high positioning accuracy. The stiffness of a structure is, however, strongly related to its mass, leading to heavy structures. This paper aims to quantify the potential gain of reducing and eliminating the stiffness constraints, which is of lesser importance for collaborative robots, by investigating the effect of applying different optimization objectives. The resulting optimized designs are quantitatively compared using a set of performance measures and evaluated against the traditional stiffness-designed approach. It was concluded that significant improvements can be made, e.g. the robot’s mass can be reduced up to 74% compared to traditionally stiff-designed robots. The dependency of the payload as well as the structural/actuator mass distribution on the optimized results is investigated and proved to have a significant influence on the potential improvements when allowing reduced structural rigidity. The relationship between structural mass and actuator mass is investigated and compared to commercially available cobots.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129787-129802
Open AccessCobots Designed for Strength, Not Stiffness
Conventional industrial robots are designed to be as stiff as possible to ensure high positioning accuracy. The stiffness of a structure is, however, strongly related to its mass, leading to heavy structures. This paper aims to quantify the potential gain of reducing and eliminating the stiffness constraints, which is of lesser importance for collaborative robots, by investigating the effect of applying different optimization objectives. The resulting optimized designs are quantitatively compared using a set of performance measures and evaluated against the traditional stiffness-designed approach. It was concluded that significant improvements can be made, e.g. the robot’s mass can be reduced up to 74% compared to traditionally stiff-designed robots. The dependency of the payload as well as the structural/actuator mass distribution on the optimized results is investigated and proved to have a significant influence on the potential improvements when allowing reduced structural rigidity. The relationship between structural mass and actuator mass is investigated and compared to commercially available cobots.
- Open Access
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 118547-118564
Vibration Control and Performance Analysis of a 3DOF High-Payload Flexible Link Manipulator
Flexible link manipulators (FLMs) are often praised for their potential advantages in industrial settings, such as being more lightweight, energy-efficient, and allowing higher operation speeds with smaller actuators. Many studies make unrealistic assumptions, like simplistic links, small deflections, low payloads, limited degrees of freedom, and well-defined mode shapes, which limit their real-world applicability. This paper investigates the performance of a flexible link manipulator with three degrees of freedom, designed for high payload capabilities and characterized by complex link shapes and complex vibration modes. An advanced control methodology was developed following the identification of the parameter-varying flexible link manipulator setup to manage the manipulator’s vibrations effectively. Comparative experiments were conducted between the flexible link manipulator and a conventional rigid link manipulator, assessing performance metrics such as repeatability, overshoot, settling time, torque and energy consumption. The results show that the flexible link manipulator, equipped with the advanced control system, achieves a repeatability of 0.14 mm, comparable to that of commercially available rigid robots. Moreover, energy consumption is reduced even with the implementation of active vibration suppression. The study highlights the potential of flexible link manipulators for real-world applications.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 118547-118564
Open AccessVibration Control and Performance Analysis of a 3DOF High-Payload Flexible Link Manipulator
Flexible link manipulators (FLMs) are often praised for their potential advantages in industrial settings, such as being more lightweight, energy-efficient, and allowing higher operation speeds with smaller actuators. Many studies make unrealistic assumptions, like simplistic links, small deflections, low payloads, limited degrees of freedom, and well-defined mode shapes, which limit their real-world applicability. This paper investigates the performance of a flexible link manipulator with three degrees of freedom, designed for high payload capabilities and characterized by complex link shapes and complex vibration modes. An advanced control methodology was developed following the identification of the parameter-varying flexible link manipulator setup to manage the manipulator’s vibrations effectively. Comparative experiments were conducted between the flexible link manipulator and a conventional rigid link manipulator, assessing performance metrics such as repeatability, overshoot, settling time, torque and energy consumption. The results show that the flexible link manipulator, equipped with the advanced control system, achieves a repeatability of 0.14 mm, comparable to that of commercially available rigid robots. Moreover, energy consumption is reduced even with the implementation of active vibration suppression. The study highlights the potential of flexible link manipulators for real-world applications.
- Open Access
- 2 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (6) , 5982-5989
Mitigating Collision Forces and Improving Response Performance in Human-Robot Interaction by Using Dual-Motor Actuators
In collaborative robotics, the safety of humans interacting with cobots is crucial. There is a need for collaborative robots that can move quickly while still being safe. This letter introduces the use of a kinematically redundant actuator in impedance control mode to reduce collision forces, aiming to improve both the safety and efficiency of collaborative robots. By distributing power across multiple drive-trains, each with unique properties such as reflected inertia, the actuator's behavior during collisions is optimized, which is key for safe interactions. Using theoretical analysis and practical experiments, we evaluate the response performance of the redundant actuator in various collision situations according to ISO/TS 15066, comparing it with that of a standard single-drive actuator. Our experiments show that the redundant actuator significantly lowers collision forces, with a 44% reduction in peak forces and an 81% decrease in transferred impulses during collisions. The letter concludes by offering a design parameter recommendation for designing actuators with reduced reflected inertia.
- 2 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (6) , 5982-5989
Open AccessMitigating Collision Forces and Improving Response Performance in Human-Robot Interaction by Using Dual-Motor Actuators
In collaborative robotics, the safety of humans interacting with cobots is crucial. There is a need for collaborative robots that can move quickly while still being safe. This letter introduces the use of a kinematically redundant actuator in impedance control mode to reduce collision forces, aiming to improve both the safety and efficiency of collaborative robots. By distributing power across multiple drive-trains, each with unique properties such as reflected inertia, the actuator's behavior during collisions is optimized, which is key for safe interactions. Using theoretical analysis and practical experiments, we evaluate the response performance of the redundant actuator in various collision situations according to ISO/TS 15066, comparing it with that of a standard single-drive actuator. Our experiments show that the redundant actuator significantly lowers collision forces, with a 44% reduction in peak forces and an 81% decrease in transferred impulses during collisions. The letter concludes by offering a design parameter recommendation for designing actuators with reduced reflected inertia.
- Open Access
- 8 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (5) , 4790-4797
Flexible Shaft as Remote and Elastic Transmission for Robot Arms
Research on human-friendly robots focuses on safety through software and hardware. Hardware-based safety offers a significant advantage over software-based safety if an accurate hardware model is integrated into the solution. Design of elastic and off-joint actuation has established safety by hardware, where the inherent qualities of elastic and lightweight nature make the robot safe for interaction. Combining series elastic actuators with cable/belt pulley-based remote transmission offers inherently safe hardware design, albeit with increased design and modeling complexity. This letter introduces remote and elastic actuation as a single-element solution for robot arm design using a flexible shaft. The test-bench approach studies the remote and elastic effects of a flexible shaft-based transmission for a robot. A set of nine flexible shafts, differing in length and diameter, are used for benchmarking as 3-D surface empirical maps to facilitate their optimal selection for robot design. An example 3 Degree Of Freedom (DOF) robot arm using a flexible shaft as a remote and elastic actuator is designed and modeled. A low-level control based on a flexible shaft is proposed, backed by the experimental results.
- 8 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (5) , 4790-4797
Open AccessFlexible Shaft as Remote and Elastic Transmission for Robot Arms
Research on human-friendly robots focuses on safety through software and hardware. Hardware-based safety offers a significant advantage over software-based safety if an accurate hardware model is integrated into the solution. Design of elastic and off-joint actuation has established safety by hardware, where the inherent qualities of elastic and lightweight nature make the robot safe for interaction. Combining series elastic actuators with cable/belt pulley-based remote transmission offers inherently safe hardware design, albeit with increased design and modeling complexity. This letter introduces remote and elastic actuation as a single-element solution for robot arm design using a flexible shaft. The test-bench approach studies the remote and elastic effects of a flexible shaft-based transmission for a robot. A set of nine flexible shafts, differing in length and diameter, are used for benchmarking as 3-D surface empirical maps to facilitate their optimal selection for robot design. An example 3 Degree Of Freedom (DOF) robot arm using a flexible shaft as a remote and elastic actuator is designed and modeled. A low-level control based on a flexible shaft is proposed, backed by the experimental results.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (8) , 5061-5068
Optimization of Mono- and Bi-Articular Parallel Elastic Elements for a Robotic Arm Performing a Pick-and-Place Task
Actuation concepts such as Series Elastic Actuation (SEA), Parallel Elastic Actuation (PEA), and Biarticular Actuation (BA), which introduce elastic elements into the structure, have the potential to reduce the electrical energy consumption of a robot. This letter presents an optimization of the arrangement of springs for a 3 degrees of freedom robotic arm, with the aim of decreasing the electrical energy consumption for a given pick-and-place task. Through simulations and experimental validation, we show that the optimal configuration in terms of electrical energy consumption and complexity consists of rigid actuation on joint 1 and PEAs on joints 2 and 3. With this configuration, root mean square (RMS) and peak load torques for a specific pick-and-place task can be reduced respectively by up to 43% and 44% for joint 2, and by 15% and 21% for joint 3 compared to the configuration without springs.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 8 (8) , 5061-5068
Optimization of Mono- and Bi-Articular Parallel Elastic Elements for a Robotic Arm Performing a Pick-and-Place Task
Actuation concepts such as Series Elastic Actuation (SEA), Parallel Elastic Actuation (PEA), and Biarticular Actuation (BA), which introduce elastic elements into the structure, have the potential to reduce the electrical energy consumption of a robot. This letter presents an optimization of the arrangement of springs for a 3 degrees of freedom robotic arm, with the aim of decreasing the electrical energy consumption for a given pick-and-place task. Through simulations and experimental validation, we show that the optimal configuration in terms of electrical energy consumption and complexity consists of rigid actuation on joint 1 and PEAs on joints 2 and 3. With this configuration, root mean square (RMS) and peak load torques for a specific pick-and-place task can be reduced respectively by up to 43% and 44% for joint 2, and by 15% and 21% for joint 3 compared to the configuration without springs.
- Open Access
- 20 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (4) , 10786-10793
A Methodology for Designing a Lightweight and Energy-Efficient Kinematically Redundant Actuator
Redundant actuators enable to distribute power among two motors, which can be selected optimally in terms of efficiency. We propose a methodology that finds effective combinations of motors and gearboxes for a dynamic load, taking into account the constraints, inertia, and efficiency of each component. Focusing on battery-operated robots as an application, it also considers battery pack mass in relation to the energy required by the actuator for multiple hours of operation. Based on this methodology, a prototype of a kinematically redundant actuator for the distal joint of a robot was built. Simulations and experiments are presented to prove the validity of the proposed approach.
- 20 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (4) , 10786-10793
Open AccessA Methodology for Designing a Lightweight and Energy-Efficient Kinematically Redundant Actuator
Redundant actuators enable to distribute power among two motors, which can be selected optimally in terms of efficiency. We propose a methodology that finds effective combinations of motors and gearboxes for a dynamic load, taking into account the constraints, inertia, and efficiency of each component. Focusing on battery-operated robots as an application, it also considers battery pack mass in relation to the energy required by the actuator for multiple hours of operation. Based on this methodology, a prototype of a kinematically redundant actuator for the distal joint of a robot was built. Simulations and experiments are presented to prove the validity of the proposed approach.
- Open Access
Novel SPECTA Actuator to Improve Energy Recuperation and Efficiency
The current state of the art in compliant actuation has already good performance, but this is still insufficient to provide a decent autonomy for the next generation of robots. In this paper, a next step is taken to improve the efficiency of actuators by tackling and enhancing the Series-Parallel Elastic Constant Torque Actuation (SPECTA) concept, which has previously been analyzed in simulations. In this work, the efficiency is increased further by decoupling the springs and their driving parts through the use of locking mechanisms, such that the motors are not always loaded and the springs can easily store energy from both input or output. Simulations have been performed to confirm this and they also showed that, in the SPECTA concept, it is always better to use high-speed motors instead of high-torque motors, even with non-efficient gearing. In this paper, the SPECTA concept is also validated experimentally with the use of a newly built test setup. In light of the obtained results, showing an increase in efficiency for almost all working points, it can be stated that SPECTA is a promising new actuation technology that allows for an increase in energy recuperation, efficiency, and autonomy.
Open AccessNovel SPECTA Actuator to Improve Energy Recuperation and Efficiency
The current state of the art in compliant actuation has already good performance, but this is still insufficient to provide a decent autonomy for the next generation of robots. In this paper, a next step is taken to improve the efficiency of actuators by tackling and enhancing the Series-Parallel Elastic Constant Torque Actuation (SPECTA) concept, which has previously been analyzed in simulations. In this work, the efficiency is increased further by decoupling the springs and their driving parts through the use of locking mechanisms, such that the motors are not always loaded and the springs can easily store energy from both input or output. Simulations have been performed to confirm this and they also showed that, in the SPECTA concept, it is always better to use high-speed motors instead of high-torque motors, even with non-efficient gearing. In this paper, the SPECTA concept is also validated experimentally with the use of a newly built test setup. In light of the obtained results, showing an increase in efficiency for almost all working points, it can be stated that SPECTA is a promising new actuation technology that allows for an increase in energy recuperation, efficiency, and autonomy.
- 1 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 3749-3756
Prismatic Gravity Compensator for Variable Payloads
Gravity compensators are passive devices that can lower the energy consumption of lifting systems by reducing the force/torque required from human users or actuators. This letter presents a prismatic gravity compensator for cranes, gantry, and other lifting systems. It is capable of statically balancing payloads between 0.8 kg and 8.7 kg over a stroke of 800 mm. The compensator is made of two modules: a constant force and a variable force module. The selection process for the components of each module is presented and a model of the compensator and its modules is developed. The impact of friction is also studied, and a strategy is proposed to still achieve balancing for various payloads.
- 1 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 3749-3756
Prismatic Gravity Compensator for Variable Payloads
Gravity compensators are passive devices that can lower the energy consumption of lifting systems by reducing the force/torque required from human users or actuators. This letter presents a prismatic gravity compensator for cranes, gantry, and other lifting systems. It is capable of statically balancing payloads between 0.8 kg and 8.7 kg over a stroke of 800 mm. The compensator is made of two modules: a constant force and a variable force module. The selection process for the components of each module is presented and a model of the compensator and its modules is developed. The impact of friction is also studied, and a strategy is proposed to still achieve balancing for various payloads.
- 1 January 2022
- Published by ASME International in Applied Mechanics Reviews
- Vol. 74 (1)
Constant Torque Mechanisms: A Survey
This work gives an overview of all types of constant torque mechanisms (CTMs) based on both function and structure. Based on their architecture, they can be divided into five distinct categories, which all have their specific behavior. It is also shown that these CTMs can be divided into two application types, namely, power assistance or torque stabilization. Constant force mechanisms (CFMs) are more prevalent in the literature; therefore, some discussion is proposed on how CFMs can be transformed into CTMs. It is also shown that some of these CTMs have a very high specific energy, which makes them potentially interesting for use as energy storage/power providers in novel fields like robotics.
- 1 January 2022
- Published by ASME International in Applied Mechanics Reviews
- Vol. 74 (1)
Constant Torque Mechanisms: A Survey
This work gives an overview of all types of constant torque mechanisms (CTMs) based on both function and structure. Based on their architecture, they can be divided into five distinct categories, which all have their specific behavior. It is also shown that these CTMs can be divided into two application types, namely, power assistance or torque stabilization. Constant force mechanisms (CFMs) are more prevalent in the literature; therefore, some discussion is proposed on how CFMs can be transformed into CTMs. It is also shown that some of these CTMs have a very high specific energy, which makes them potentially interesting for use as energy storage/power providers in novel fields like robotics.
- Open Access
- 31 January 2019
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 38 (5) , 612-629
Kinematically redundant actuators, a solution for conflicting torque–speed requirements
Robots often switch from highly dynamic motion to delivering high torques at low speeds. The actuation requirements for these two regimes are very different. As a consequence, the average efficiency of the actuators is typically much lower than the efficiency at the optimal working point. A potential solution is to use multiple motors for a single motor joint. This results in a redundant degree of freedom, which can be exploited to make the system more efficient overall. In this work, we explore the potential of kinematically redundant actuators in dynamic applications. The potential of a kinematically redundant actuator with two motors is evaluated against a single-motor equivalent in terms of operating range, maximum acceleration, and energy consumption. We discuss how the comparison is influenced by the design of the actuator and the way how the power is distributed over the input motors. Our results support the idea that kinematically redundant actuators can resolve the conflicting torque–speed requirements typical of robots.
- 31 January 2019
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 38 (5) , 612-629
Open AccessKinematically redundant actuators, a solution for conflicting torque–speed requirements
Robots often switch from highly dynamic motion to delivering high torques at low speeds. The actuation requirements for these two regimes are very different. As a consequence, the average efficiency of the actuators is typically much lower than the efficiency at the optimal working point. A potential solution is to use multiple motors for a single motor joint. This results in a redundant degree of freedom, which can be exploited to make the system more efficient overall. In this work, we explore the potential of kinematically redundant actuators in dynamic applications. The potential of a kinematically redundant actuator with two motors is evaluated against a single-motor equivalent in terms of operating range, maximum acceleration, and energy consumption. We discuss how the comparison is influenced by the design of the actuator and the way how the power is distributed over the input motors. Our results support the idea that kinematically redundant actuators can resolve the conflicting torque–speed requirements typical of robots.