Ben Silvester
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ben Silvester has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Juliette Soulard
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K.
2 shared publications Claire Davis
1 shared publication- Edward. Griffin
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K.
1 shared publication - Fanfu Wu
Warwick Manufacturing Group, University of Warwick, Coventry, U.K.
1 shared publication - Lei Zhou
Warwick Manufacturing Group, University of Warwick, Coventry, U.K.
1 shared publication - X. Y. Ma
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K
1 shared publication
Latest Publications
- 19 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-10
Repeatability of Tests for Validation of Iron Loss Models in Electrical Machines
Prediction of iron loss in electrical machines is known to be a challenging task. The concept of a building factor to account for discrepancy between predicted and measured loss is widely used. From literature, these building factors may need to be as high as 1.5 to 2, i.e., a discrepancy of up to 100%, leading to different impact on total losses for every electrical machine. To calibrate the building factor, modelling and testing are required. This paper describes an extensive test campaign on PM synchronous machines at no-load with magnetized and dummy rotors. Several challenges to accurately quantify no-load iron loss by dynamic testing for model calibration are reported, highlighting the benefits of rotor temperatures monitoring, and performing repeatability checks. For accurate prediction of iron loss impacted by mechanical stress (due to cut edge damage or shrink-fit for example), advanced modelling approaches require electrical steel properties (BH and loss density) as function of tensile and compressive stress. Such measurements with a dedicated single sheet tester have not yet been standardized. Repeatability issues and spread of measured data are presented and their influence mitigated by a pre-cycling procedure. A novel method to compare the impact of stress on several electrical steel grades including thicknesses from 0.1 mm to 0.35 mm indicates different grades follow similar trends. However, the changes are grade-specific, requiring characterization of each material grade at multiple stress level, frequency, and flux density for advanced modelling of e-machine performance.
- 19 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-10
Repeatability of Tests for Validation of Iron Loss Models in Electrical Machines
Prediction of iron loss in electrical machines is known to be a challenging task. The concept of a building factor to account for discrepancy between predicted and measured loss is widely used. From literature, these building factors may need to be as high as 1.5 to 2, i.e., a discrepancy of up to 100%, leading to different impact on total losses for every electrical machine. To calibrate the building factor, modelling and testing are required. This paper describes an extensive test campaign on PM synchronous machines at no-load with magnetized and dummy rotors. Several challenges to accurately quantify no-load iron loss by dynamic testing for model calibration are reported, highlighting the benefits of rotor temperatures monitoring, and performing repeatability checks. For accurate prediction of iron loss impacted by mechanical stress (due to cut edge damage or shrink-fit for example), advanced modelling approaches require electrical steel properties (BH and loss density) as function of tensile and compressive stress. Such measurements with a dedicated single sheet tester have not yet been standardized. Repeatability issues and spread of measured data are presented and their influence mitigated by a pre-cycling procedure. A novel method to compare the impact of stress on several electrical steel grades including thicknesses from 0.1 mm to 0.35 mm indicates different grades follow similar trends. However, the changes are grade-specific, requiring characterization of each material grade at multiple stress level, frequency, and flux density for advanced modelling of e-machine performance.
- Open Access
- 17 February 2022
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 551
Quantitative characterisation and modelling of the effect of cut edge damage on the magnetic properties in NGO electrical steel
- 17 February 2022
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 551
Open AccessQuantitative characterisation and modelling of the effect of cut edge damage on the magnetic properties in NGO electrical steel