Edward. Griffin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Edward. Griffin has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Juliette Soulard
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K.
2 shared publications - Ali Sadeghianjahromi
National Chiao Tung University
1 shared publication - Ben Silvester
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K
1 shared publication - X. Y. Ma
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K
1 shared publication - Yaohui Gai
Xidian University
1 shared publication - Yufeng. Guo
Warwick Manufacturing Group (WMG), University of Warwick, Coventry, U.K.
1 shared publication
Latest Publications
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7557-7565
Heat Transfer Characteristics of Oil Jet Impingement Cooling on a Stator Segment Exterior Surface for Traction Motors With Concentrated Windings
This paper addresses the heat transfer characteristics of an oil jet impingement cooling on a stator segment exterior surface, which is evaluated for use in a traction motor with concentrated windings. The fluid flow on the segment exterior surface and its heat transfer coefficient (HTC) are estimated using computational fluid dynamics (CFD) based on a meshless moving particle simulation (MPS) method. The temperature distribution of a stator segment is then analysed using finite element analysis (FEA) with the assistance of HTC mapping provided by CFD. Finally, experiments are conducted to validate the results obtained from numerical models and to assess the impact factors on the cooling performance, such as the inlet oil flow rate, inlet oil temperature, jet to segment distance and segment inclined angle. For the first time, this study identifies and evaluates the key parameters influencing oil jet impingement cooling on the segmented stator’s exterior surface by coupling meshless CFD and FEA simulations, significantly reducing overall simulation time. This comprehensive analysis provides valuable insights for future implementation in a complete motor system.
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (3) , 7557-7565
Heat Transfer Characteristics of Oil Jet Impingement Cooling on a Stator Segment Exterior Surface for Traction Motors With Concentrated Windings
This paper addresses the heat transfer characteristics of an oil jet impingement cooling on a stator segment exterior surface, which is evaluated for use in a traction motor with concentrated windings. The fluid flow on the segment exterior surface and its heat transfer coefficient (HTC) are estimated using computational fluid dynamics (CFD) based on a meshless moving particle simulation (MPS) method. The temperature distribution of a stator segment is then analysed using finite element analysis (FEA) with the assistance of HTC mapping provided by CFD. Finally, experiments are conducted to validate the results obtained from numerical models and to assess the impact factors on the cooling performance, such as the inlet oil flow rate, inlet oil temperature, jet to segment distance and segment inclined angle. For the first time, this study identifies and evaluates the key parameters influencing oil jet impingement cooling on the segmented stator’s exterior surface by coupling meshless CFD and FEA simulations, significantly reducing overall simulation time. This comprehensive analysis provides valuable insights for future implementation in a complete motor system.
- 19 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-10
Repeatability of Tests for Validation of Iron Loss Models in Electrical Machines
Prediction of iron loss in electrical machines is known to be a challenging task. The concept of a building factor to account for discrepancy between predicted and measured loss is widely used. From literature, these building factors may need to be as high as 1.5 to 2, i.e., a discrepancy of up to 100%, leading to different impact on total losses for every electrical machine. To calibrate the building factor, modelling and testing are required. This paper describes an extensive test campaign on PM synchronous machines at no-load with magnetized and dummy rotors. Several challenges to accurately quantify no-load iron loss by dynamic testing for model calibration are reported, highlighting the benefits of rotor temperatures monitoring, and performing repeatability checks. For accurate prediction of iron loss impacted by mechanical stress (due to cut edge damage or shrink-fit for example), advanced modelling approaches require electrical steel properties (BH and loss density) as function of tensile and compressive stress. Such measurements with a dedicated single sheet tester have not yet been standardized. Repeatability issues and spread of measured data are presented and their influence mitigated by a pre-cycling procedure. A novel method to compare the impact of stress on several electrical steel grades including thicknesses from 0.1 mm to 0.35 mm indicates different grades follow similar trends. However, the changes are grade-specific, requiring characterization of each material grade at multiple stress level, frequency, and flux density for advanced modelling of e-machine performance.
- 19 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-10
Repeatability of Tests for Validation of Iron Loss Models in Electrical Machines
Prediction of iron loss in electrical machines is known to be a challenging task. The concept of a building factor to account for discrepancy between predicted and measured loss is widely used. From literature, these building factors may need to be as high as 1.5 to 2, i.e., a discrepancy of up to 100%, leading to different impact on total losses for every electrical machine. To calibrate the building factor, modelling and testing are required. This paper describes an extensive test campaign on PM synchronous machines at no-load with magnetized and dummy rotors. Several challenges to accurately quantify no-load iron loss by dynamic testing for model calibration are reported, highlighting the benefits of rotor temperatures monitoring, and performing repeatability checks. For accurate prediction of iron loss impacted by mechanical stress (due to cut edge damage or shrink-fit for example), advanced modelling approaches require electrical steel properties (BH and loss density) as function of tensile and compressive stress. Such measurements with a dedicated single sheet tester have not yet been standardized. Repeatability issues and spread of measured data are presented and their influence mitigated by a pre-cycling procedure. A novel method to compare the impact of stress on several electrical steel grades including thicknesses from 0.1 mm to 0.35 mm indicates different grades follow similar trends. However, the changes are grade-specific, requiring characterization of each material grade at multiple stress level, frequency, and flux density for advanced modelling of e-machine performance.