Dongwon Jang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dongwon Jang has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Hyun-Yong Yu
School of Electrical Engineering, Korea University, Seoul, South Korea
4 shared publications Seong-Ji Min
Korea University
4 shared publications- Seung-Geun Jung
School of Electrical Engineering, Korea University, Seoul, South Korea
3 shared publications - Euyjin Park
School of Electrical Engineering, Korea University, Seoul, South Korea
2 shared publications Alum Jung
Samsung Advanced Institute of Technology, Samsung Electronics Co., Ltd, Suwon, Republic of Korea
1 shared publication- Chang Seok Lee
Advanced Device Platform Samsung Advanced Institute of Technology Suwon South Korea
1 shared publication
Latest Publications
- 12 September 2026
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 130 (38) , 13265-13272
Analysis of Fermi-Level Pinning in Silicide/Si Structures with Various Interface Vacancy Defects
As CMOS technologies scale, contact resistance at metal/semiconductor interfaces, particularly silicide/Si, has become a key performance limiter. Although silicide/Si generally exhibits low Schottky barrier heights (SBHs) and weak Fermi-level pinning (FLP), vacancy-type defects can substantially alter interfacial electronic properties. Here, density functional theory (DFT) calculations are performed on silicide/Si interfaces, comparing an ideal interface with three single-vacancy configurations: a metal vacancy in the silicide, a Si vacancy in the silicide, and a Si vacancy in the Si region near the interface. A dilute-defect limit is considered by introducing one vacancy per lateral interface area of the supercell (≈0.0052 Å–2). The results show that FLP is governed primarily by defect location. Vacancies within the silicide suppress interfacial charge redistribution and weaken MIGS-like characteristics, leading to reduced pinning and higher pinning factors (S ≈ 0.51–0.52). In contrast, a Si vacancy on the semiconductor side perturbs near-interface electrostatics and enhances LDOS tails in the Si bandgap, resulting in stronger pinning (S ≈ 0.14). This vacancy-induced modulation of FLP directly translates into systematic shifts in SBHs, providing atomistic insight into defect-mediated FLP in silicide/Si interfaces.
- 12 September 2026
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 130 (38) , 13265-13272
Analysis of Fermi-Level Pinning in Silicide/Si Structures with Various Interface Vacancy Defects
As CMOS technologies scale, contact resistance at metal/semiconductor interfaces, particularly silicide/Si, has become a key performance limiter. Although silicide/Si generally exhibits low Schottky barrier heights (SBHs) and weak Fermi-level pinning (FLP), vacancy-type defects can substantially alter interfacial electronic properties. Here, density functional theory (DFT) calculations are performed on silicide/Si interfaces, comparing an ideal interface with three single-vacancy configurations: a metal vacancy in the silicide, a Si vacancy in the silicide, and a Si vacancy in the Si region near the interface. A dilute-defect limit is considered by introducing one vacancy per lateral interface area of the supercell (≈0.0052 Å–2). The results show that FLP is governed primarily by defect location. Vacancies within the silicide suppress interfacial charge redistribution and weaken MIGS-like characteristics, leading to reduced pinning and higher pinning factors (S ≈ 0.51–0.52). In contrast, a Si vacancy on the semiconductor side perturbs near-interface electrostatics and enhances LDOS tails in the Si bandgap, resulting in stronger pinning (S ≈ 0.14). This vacancy-induced modulation of FLP directly translates into systematic shifts in SBHs, providing atomistic insight into defect-mediated FLP in silicide/Si interfaces.
- 9 January 2026
- Published by Springer Nature in Nature Materials
- Vol. 25 (5) , 824-831
Gate structuring on n-type bilayer MoS2 field-effect transistors for ultrahigh current density
The foundry industry and academia are confronting the limits of Moore’s Law scaling for logic transistors. Silicon field‑effect transistors (FETs) now rely on gate‑all‑around structures and ultrathin channels, even at the cost of decreased carrier mobility and complex fabrication processes. Two‑dimensional (2D) semiconductors offer a promising alternative because they retain their crystalline quality at atomic thicknesses. Nonetheless, whether they truly exhibit higher performance than silicon remains questionable. Here, by implementing a dual‑gate structure on bilayer MoS2 FETs, we mitigate the fringing‑field barrier created by the elevated top contact and achieve high carrier densities without increasing fabrication complexity. Simulations and statistical analysis confirm that the dual‑gate compensates the fringe field, enabling a drain current of 1.55 mA µm−1 even with conventional gold contacts. Quantum‑transport simulation indicates that, with further gate‑length and equivalent‑oxide‑thickness scaling, the on-state current can reach levels comparable to silicon FETs at the 3-nm node, and monolithic 3D integration can extend the applicability of dual‑gate 2D transistors to future logic technologies.
- 9 January 2026
- Published by Springer Nature in Nature Materials
- Vol. 25 (5) , 824-831
Gate structuring on n-type bilayer MoS2 field-effect transistors for ultrahigh current density
The foundry industry and academia are confronting the limits of Moore’s Law scaling for logic transistors. Silicon field‑effect transistors (FETs) now rely on gate‑all‑around structures and ultrathin channels, even at the cost of decreased carrier mobility and complex fabrication processes. Two‑dimensional (2D) semiconductors offer a promising alternative because they retain their crystalline quality at atomic thicknesses. Nonetheless, whether they truly exhibit higher performance than silicon remains questionable. Here, by implementing a dual‑gate structure on bilayer MoS2 FETs, we mitigate the fringing‑field barrier created by the elevated top contact and achieve high carrier densities without increasing fabrication complexity. Simulations and statistical analysis confirm that the dual‑gate compensates the fringe field, enabling a drain current of 1.55 mA µm−1 even with conventional gold contacts. Quantum‑transport simulation indicates that, with further gate‑length and equivalent‑oxide‑thickness scaling, the on-state current can reach levels comparable to silicon FETs at the 3-nm node, and monolithic 3D integration can extend the applicability of dual‑gate 2D transistors to future logic technologies.
- Open Access
- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 41112-41118
Device Design Guidelines of 3-nm Node Complementary FET (CFET) in Perspective of Electrothermal Characteristics
For the first time, device design guidelines for a 3-nm node complementary field-effect transistor (CFET), which vertically stacks n-type and p-type nanosheet MOSFETs with a shared gate, are investigated using calibrated 3-D technology computer-aided design (TCAD). Here, the optimal device dimensions of the CFETs for better inverter performance and thermal characteristics are studied. The electrothermal performance are investigated for various vertical dimension parameters of CFET, such as the number of stacked channels, vertical distance between nanosheet channels (D nsh ), distance of n/pMOS separation (D n/p ), and channel thicknesses (T nsh ). The results show that, unlike conventional CMOS, the reduction of D nsh and D n/p of CFET can effectively improve inverter performance without severe thermal degradation, although other dimensional parameters trigger a severe trade-off between different electrothermal parameters. The reduction of D nsh and D n/p decreases C eff with a lower metal via the height and gate fringing effect. However, the reduction in D nsh and D n/p does not change R eff ; therefore, both the operation frequency ( $f$ ) and power-product delay (PDP) can be improved. In the case of thermal characteristics, the reduction of D nsh and D n/p slightly increases both T max and R th because of thermal coupling but is negligible. Therefore, the reduction of D nsh and D n/p will be a key technique for the development of sub-3-nm CFET.
- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 41112-41118
Open AccessDevice Design Guidelines of 3-nm Node Complementary FET (CFET) in Perspective of Electrothermal Characteristics
For the first time, device design guidelines for a 3-nm node complementary field-effect transistor (CFET), which vertically stacks n-type and p-type nanosheet MOSFETs with a shared gate, are investigated using calibrated 3-D technology computer-aided design (TCAD). Here, the optimal device dimensions of the CFETs for better inverter performance and thermal characteristics are studied. The electrothermal performance are investigated for various vertical dimension parameters of CFET, such as the number of stacked channels, vertical distance between nanosheet channels (D nsh ), distance of n/pMOS separation (D n/p ), and channel thicknesses (T nsh ). The results show that, unlike conventional CMOS, the reduction of D nsh and D n/p of CFET can effectively improve inverter performance without severe thermal degradation, although other dimensional parameters trigger a severe trade-off between different electrothermal parameters. The reduction of D nsh and D n/p decreases C eff with a lower metal via the height and gate fringing effect. However, the reduction in D nsh and D n/p does not change R eff ; therefore, both the operation frequency ( $f$ ) and power-product delay (PDP) can be improved. In the case of thermal characteristics, the reduction of D nsh and D n/p slightly increases both T max and R th because of thermal coupling but is negligible. Therefore, the reduction of D nsh and D n/p will be a key technique for the development of sub-3-nm CFET.
- Open Access
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 78-82
Performance Analysis on Complementary FET (CFET) Relative to Standard CMOS With Nanosheet FET
For the first time, by using 3-D TCAD, the advantage of using complementary FET (CFET), which has vertically stacked nanosheet nFET and pFET with shared gate, is compared to standard CMOS with nanosheet FETs in perspective of CMOS inverter performance. The comparative study on CMOS operation was performed between CFET and standard CMOS in 3-nm technology node. The results indicate that, when both devices have identical DC electrical characteristics, using CFET can increase the frequency by ~2.3% in iso-power and decrease power by ~7.3% in iso-frequency compared to the standard CMOS with separate n/pFETs while effectively reducing the area by ~55%. It is also investigated that such results are due to the approximately 4.5% low effective capacitance (C eff ) of the CFET compared to the standard CMOS. This low C eff of CFET arises from the stacked structure, which causes the gate-fringe electric field overlap and short via pitch between nFET and pFET. Furthermore, the performance of CFET by different n/pFET separation distances, channel lengths, and widths are analyzed. This study can provide critical insight into the performance improvement by using CFET for sub 3-nm technology.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 78-82
Open AccessPerformance Analysis on Complementary FET (CFET) Relative to Standard CMOS With Nanosheet FET
For the first time, by using 3-D TCAD, the advantage of using complementary FET (CFET), which has vertically stacked nanosheet nFET and pFET with shared gate, is compared to standard CMOS with nanosheet FETs in perspective of CMOS inverter performance. The comparative study on CMOS operation was performed between CFET and standard CMOS in 3-nm technology node. The results indicate that, when both devices have identical DC electrical characteristics, using CFET can increase the frequency by ~2.3% in iso-power and decrease power by ~7.3% in iso-frequency compared to the standard CMOS with separate n/pFETs while effectively reducing the area by ~55%. It is also investigated that such results are due to the approximately 4.5% low effective capacitance (C eff ) of the CFET compared to the standard CMOS. This low C eff of CFET arises from the stacked structure, which causes the gate-fringe electric field overlap and short via pitch between nFET and pFET. Furthermore, the performance of CFET by different n/pFET separation distances, channel lengths, and widths are analyzed. This study can provide critical insight into the performance improvement by using CFET for sub 3-nm technology.
- Open Access
- 25 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 158116-158121
Electrothermal Characterization and Optimization of Monolithic 3D Complementary FET (CFET)
For the first time, the electrothermal characteristics of a three-dimensional (3D) monolithic complementary FET (CFET) in DC operation as well as in AC CMOS operation were investigated with TCAD simulations. The self-heating effect (SHE) in a monolithic CFET is expected to be a critical problem given its highly compact architecture. DC analysis of the individual NFET and PFET devices revealed that increasing the channel width from 5.0 to 7.0 nm improved the thermal resistance up to 8.5% and the RC delay up to 9.6%, while greatly deteriorating the on/off ratio. AC CMOS inverter simulations of the CFET showed that reducing the NFET/PFET vertical separation from 30 to 10 nm resulted in 11.9% faster operation frequency and 3.4% reduced dynamic power loss, but 11.2% higher rise in device temperature. The clear trade-off relationships between the thermal and electrical performance factors necessitate optimization of the device dimension parameters. These findings are expected to provide critical insight for the design technology co-optimization (DTCO) in the 3-nm regime.
- 25 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 158116-158121
Open AccessElectrothermal Characterization and Optimization of Monolithic 3D Complementary FET (CFET)
For the first time, the electrothermal characteristics of a three-dimensional (3D) monolithic complementary FET (CFET) in DC operation as well as in AC CMOS operation were investigated with TCAD simulations. The self-heating effect (SHE) in a monolithic CFET is expected to be a critical problem given its highly compact architecture. DC analysis of the individual NFET and PFET devices revealed that increasing the channel width from 5.0 to 7.0 nm improved the thermal resistance up to 8.5% and the RC delay up to 9.6%, while greatly deteriorating the on/off ratio. AC CMOS inverter simulations of the CFET showed that reducing the NFET/PFET vertical separation from 30 to 10 nm resulted in 11.9% faster operation frequency and 3.4% reduced dynamic power loss, but 11.2% higher rise in device temperature. The clear trade-off relationships between the thermal and electrical performance factors necessitate optimization of the device dimension parameters. These findings are expected to provide critical insight for the design technology co-optimization (DTCO) in the 3-nm regime.