PCPetro Chulanov

Petro Chulanov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Petro Chulanov has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    APPLICATION OF STRAIN GAUGES IN MONITORING LOAD-BEARING ELEMENTS OF BUILDING STRUCTURES

    by Oleksandr Isayev, Svitlana Bondar, Petro Chulanov, Andrii Bulhakov

    The paper addresses the application of strain gauges, classified as strain-based sensors, in structural health monitoring of engineering constructions. Particular attention is given to monitoring the bending behavior of relatively tall columns subjected to variable and increasing loads. It is shown that the use of resistive strain gauges enables continuous measurement of relative strains and the indirect evaluation of stresses within structural elements with high sensitivity and accuracy. This allows for the detection of adverse changes in structural behavior at early stages, including stress redistribution and the initiation of damage. It is emphasized that strain measurements are inherently local, reflecting the state of the material only at specific points where sensors are installed. Therefore, they do not directly provide information about the global displacements of structures, such as deflections, tilts, or planimetric and vertical movements. To assess these parameters, geodetic monitoring methods must be employed using robotic total stations and other high-precision measurement instruments. Based on the analysis, the necessity of an integrated approach combining strain measurement and geodetic monitoring is substantiated. Such an approach enables the simultaneous acquisition of local stress–strain state characteristics and global spatial behavior parameters, significantly improving the reliability of structural assessment and prediction. The paper also discusses practical aspects of monitoring system design, including the selection of locations and mounting techniques for strain gauges, determination of the required number of sensors, and optimization of their layout. Special attention is paid to coordinating the placement of strain gauges with reflective targets used for coordinate measurements by robotic total stations. This ensures the effective integration of heterogeneous data sources and enhances the overall effectiveness of comprehensive structural monitoring.

  • Open Access

    APPLICATION OF INCLINOMETERS FOR COLUMN INSTALLATION

    by Oleksandr Isayev, Oleksandr Kuzmych, Svitlana Bondar, Petro Chulanov

    The structure is described as consisting of two straight rods arranged along the same vertical line. One rod serves as the load-bearing element, while the other is the loading element. In the расчетнаясхема, the loading rod is replaced by a force vector. Under very large loads and certain influencing factors, the load-bearing rod may enter an unstable state and undergo significant deformation. One of these factors is the inclination of the rod, either as a residual value after alignment and installation or as an acquired value under the action of load, temperature, or ground displacements. This explains the need for high accuracy in setting columns in a vertical position, especially when they are relatively slender and long rods. The required accuracy can be ensured by geodetic methods. Such work is analyzed, and it is concluded that guaranteeing the required accuracy involves significant time, careful preparation, and additional geodetic layouts and measurements. Therefore, the possibility of using inclinometers (tilt sensors) is considered; among the various types, MEMS inclinometers are selected. According to measurement accuracy, they can be classified as technical, precise, and high-precision devices. The permissible deviation of a column axis from the vertical position is regulated by normative documents. In this study, reference is made to the State Standard of Ukraine, and the maximum permissible deviations of a column from verticality are presented in different forms and as functions of column height. Based on an interval estimation of accuracy, a transition is made from the maximum permissible deviation to the root-mean-square deviation and to the root-mean-square error, which represents the practical meaning of the permissible deviation. The practical value of the root-mean-square error, formed by many sources of error, is expressed as a sum of components characterizing these sources. From this series, the root-mean-square error of the instrument itself (the sensor) is singled out. The results are expressed as functions of column height and a statistical coefficient. By comparing these data, sensors can be selected according to their accuracy characteristics. Several examples of precise and high-precision sensors are considered, and conclusions regarding their application are drawn.

  • Open Access

    ALGEBRAIC ADJUSTMENT OF MEASURED TRIANGLE ELEMENTS

    by Valeriy Gladilin, Oksana Kaminetska, Tatiana Siroshtan, Tetyana Sviderska, Iryna Hamalii, Nataliia Shudra, Petro Chulanov, Валерій Гладілін, Тетяна Сіроштан, Тетяна Свідерська, et al.

    It is difficult to align the measured elements of the triangle. A method of alignment using algebraic circles is proposed. If six elements are measured in a triangle: angles A, B, C, lengths of opposite sides a, b, c with mean square errors mA, mB, mC, ma, mb, mc, the values of the equalized elements must satisfy the requirements of the equations where D is the metric parameter of the triangle (the metric value through which the mathematical relationship between the sides and angles of the triangle is established), that is, the value of the diameter of the circle. If , which are found by formulas (1) and condition (2) is fulfilled, then this confirms the validity of the theorem of sines. In fact, it is a symmetrical set, because the number and composition of the upper indices corresponds to the number and composition of the lower indices, and this is a reflection of dimensions, since the triangle ABC has pairs of opposite elements: а- А; b- B; c- C. Let's construct the graph G Do of the diameter of the circle circumscribed around the aligned triangle, for which we will first construct the graphs G Di of the diameters of the circles circumscribed around the T-triangles, which are shown in fig. 1, and then combine them. Three vertices a, b, c form a "plane" - this is a metric field. The reflection of the metric field is the field of angular measurements - a "plane" defined by three points A, B, C. Note that for a measured triangle, the reflection of the metric field in the angular one is not unambiguous, so the first plane in fig. 1 is "inclined" to the second. After determining the most likely metric parameter Do of the triangle, it is possible to bring these planes into full correspondence. That is, Do is a "lens" [4],[8] with the help of which we obtain an unambiguous mapping of the metric field in the angular field and vice versa.

  • Open Access

    THE PROBLEM OF RELIABILITY OF GEODESIC NETWORKS

    by Valeriy Gladilin, Anatolij Maznitskij, Tatiana Siroshtan, Tetyana Sviderska, Irina Gamalij, Natalia Shudra, Petro Chulanov

    В наш час теорія надійності широко використовується в будівельному виробництві, а також використовується і в області геодезії. Шляхом абстрагування її положення можна з успіхом перенести і на системи, які, здавалося б, не знаходяться в динамічному стані. Візьмемо, наприклад, пункти полігонометричної (нівелірної) мережі в місті. Здавалося б, що така мережа знаходиться в статичному стані, однак з плином часу вона зазнає змін, тобто вона знаходиться в непомітній динаміці і надійність її поступово знижується. Під надійністю в широкому сенсі цього слова розуміють здатність технічного пристрою (системи, мережі) до безперебійної (безвідмовної) роботи упродовж заданого проміжку часу у певних умовах. Такий проміжок часу зазвичай зумовлено часом виконання деякої задачі, яка здійснюється приладом чи системою і є частиною загальної операційної задачі в вирішенні топографо-геодезичних робіт. В даний час проблема надійності стає однією з вузлових проблем техніки та організації управління. Забезпечення надійної роботи всіх елементів системи – є першорядною важливістю.

  • Open Access

    Monitoring of structures with bearing elements in the form of long vertical rods

    by Oleksandr Isaev, Svitlana Bondar, Yurii Medvedskyi, Petro Chulanov, Olena Tsykolenko

    A building structure is considered, which in the design form consists of two vertical rectilinear interacting elements. One of them is loading, the other is carrying. The bearing element is presented in the form of a long thin rod loaded with an external axial vertical force. Due to the errors of geodetic verification and installation work, the bearing rod will be installed with some inclination and displacement relative to the coordinate axes. The external load on the bearing element is represented by the force vector, which is equivalent to the loading rod. Errors of geodetic verification and installation work will change the design direction of the force line and its design position on the supporting element. An inclined force vector will have a vertical and horizontal force component. Thus, the line of action of the loading force and the longitudinal axis of the supporting rod will be located at an angle to each other, which will cause bending momentsand transverse forces in the sections of the rod. A design "changed" in relation to the project is created. Bending moments and horizontal forces in this design will contribute to premature bending of the rod. An unevenly heated rod also acquires the ability to distort. The influence of the specified factors can be increased, and the stability of the rod significantly weakened due to uneven subsidence, horizontal displacement or tilting of the supporting structure due to dangerous exogenous geological processes. Therefore, errors in the position of elements, changes in temperature, geological processes disrupt the linear form of equilibrium of the bearing rod and its position in space. The change in shape and relative position contributes to the premature emergence of an unstable state under an increasing external load. In the changed design, the bearing rod may suddenly find itself in a critical stress-deformed state. The task of monitoring is to sense and properly record changes and dynamics of the stress-strain state. For this purpose, measuring complexes with a certain configuration are designed, which provide with the necessary specified accuracy the measurement of changes in the physical state of the elements of building structures.

  • Open Access

    PROPERTIES OF TRUE ERRORS OF GEODESIC MEASUREMENTS IN THE ALGEBRAIC CIRCLE

    by Valeriy Gladilin, Anatolij Maznitskij, Tatiana Siroshtan, Tetyana Sviderska, Irina Gamalij, Natalia Shudra, Petro Chulanov

    Істинні похибки можливо знайти коли ми знаємо істинне значення вимірюваної величини. В геодезичних вимірах та і в будь – яких інших вимірюваннях істинне значення вимірюваної величини невідоме, тому приймається якесь найбільш ймовірне значення цієї величини, сума ймовірних похибок повинна дорівнювати нулю, сума істинних похибок повинна дорівнювати нулю, тому необхідно дослідити ймовірні та істинні похибки в алгебраїчному колі. Розглядається новий метод оцінки точності вимірів він відрізняється від традиційних тим, що в результаті обробки вимірів однієї величини одержують не тільки загальну середню квадратичну похибку, а й середні квадратичні похибки всіх вимірів.

  • Open Access

    CALCULATION OF THE CORRELATION COEFFICIENT IN GEODETIC MEASUREMENTS

    by Valeriy Gladilin, Tatiana Siroshtan, Iryna Нamalіі, Tetyana Sviderska, Nataliia Shudra, Petro Chulanov

    Пропонується формула для визначення коефіцієнтів кореляції, за якою при малій кількості вимірювань значення коефіцієнтів будуть більшими в порівнянні з величинами обчисленими за відомими формулами, тобто ці значення будуть менше зміщеними по відношенню до істинних величин коефіцієнтів кореляції. В геодезії взагалі обмежуються невеликою кількістю вимірювань, в фотограмметрії при взаємному орієнтуванні знімків стереопари в автоматичному режимі (на станції Дельта) при ідентифікації точок на лівому і правому знімках необхідно точно обчислювати значення коефіцієнтів кореляції, що дає можливість побудувати кращу фотограмметричну модель зображення місцевості.

  • Open Access

    SEQUENTIAL ANALYSIS OF CONTROL MEASUREMENTS IN TOPOGRAPHIC AND GEODETIC PRODUCTION

    by Gladilin Valeriy, Tatiana Siroshtan, Tetyana Sviderska, Nataliia Shudra, Petro Chulanov

    При виконанні топографічної зйомки, при виконанні планувальних, будівельно – монтажних та інших робіт, необхідно виконувати контрольно – геодезичні вимірювання якості їх виконання. До теперішнього часу контрольно – геодезичні вимірювання встановлювались з різних міркувань, які не мали цілком конкретного науково – виробничого підходу.

  • Open Access

    Monitoring of the elements stability of building constructions by means of example of vertical elastic rod of high flexibility

    by Oleksandr Isaev, Andrii Annenkov, Roman Demianenko, Petro Chulanov

    The article is related to the field of geodetic and engineering construction monitoring of building structures in the form of rod systems. It investigates the measurement accuracy of the compression deformation of the rod. As an example, there is considered a vertical rectilinear rod of high flexibility, loaded with a longitudinal axial force. Experience demonstrates that the rod, under the influence of an axial compressive load not exceeding the permissible design values, retains its original form of equilibrium and stability. At the same time, it works in the field of elastic compression deformations. As the load increases to its critical values, there occurs a particular state of the element when the form of equilibrium becomes unstable, and at any moment, it can turn from a straight line into a curvilinear one with a slight external influence or as a result of position errors. This is accompanied by large displacements and permanent deformations. The importance of monitoring is noted when a building structure with similar constructions, for example, is situated in the area of development of negative natural and anthropogenic processes. As a result, the load on some elements may increase to critical values due to uneven horizontal and vertical displacement and inclination of the structure, including vibrations, etc. Attention is focused on the fact that the complex of engineering and technical measurements should show, with the necessary completeness, reliability and accuracy of the value, the nature and dynamics of changes in the external load on the elements of the building structure, changes in internal forces and stresses in them, the development of deformations (changes in the size and shape of equilibrium). There is explained the accuracy with which it is necessary to measure the displacement of the rod end during the deformation. There was derived the dependence with the help of which it is possible to see the root-mean-square error of the displacement measuring that depends on the choice of the maximum stress deviation in the sections of the rod made of a certain material. There is laid out the calculation of the maximum stress deviation based on the stability and flexibility of the rod.


  • Open Access

    CONSTRUCTION OF GEODESIC NETWORKS ON THE BASIS OF THE THEORY OF MARKOV ACCIDENTAL PROCESSES AND THE THEORY OF RELIABILITY

    by Valeriy Gladilin, Tatiana Siroshtan, Irina Gamalij, Nataliia Shudra, Petro Chulanov, Валерій Гладілін, Тетяна Сіроштан, Ірина Гамалій

    As mentioned above, the theory of reliability was mainly developed for technical devices. However, nowadays it is widely used in construction, and is also beginning to be used in geodesy. By abstracting its position can be successfully transferred to systems that do not seem to be in a dynamic state. Take, for example, the polygon metric network in the city. It would seem that such a network is in a static state, but over time it undergoes changes, ie it is in subtle dynamics and its reliability is gradually declining. Reliability in the broadest sense of the word means the ability of a technical device (system, network) to uninterrupted (trouble-free) operation for a specified period of time under certain conditions. This period of time is usually due to the time of a task. Which is carried out by a device or system and is part of the overall operational task. Currently, the problem of reliability is becoming one of the key problems of technology and management. Ensuring the reliable operation of all elements of the system is of paramount importance. Improving reliability requires special study and quantitative analysis of the phenomena associated with accidental failures of devices or systems. At this time, the theory of reliability has become a special science that makes extensive use of probable methods of examination. In the theory of reliability there are two types of failures: sudden and gradual. Consider sudden failures. Sudden device failures are understood as an instantaneous failure, which means that it cannot be used, and these failures occur at some random point in time. The reliability of the system depends on the composition and number of elements included in it, on the type of integration into the system and on the characteristics of each individual element. An element is to be understood as any device that is not subject to further disconnection, the reliability of which is specified or determined experimentally. By assembling such elements in different ways into systems, we will solve the problem of determining the reliability of the system depending on the reliability of its elements. The reliability of elements and systems is determined by numerical characteristics. We give some definitions of these characteristics for the element and the system as a whole. The reliability of the element is the probability that the element in certain conditions will work flawlessly over time, its probability is denoted. With increasing time, reliability usually decreases; with probability. In the geodetic literature, the term "reliability" is often used, which means the accuracy of the obtained results of geodetic measurements. However, the reliability of a geodetic sign or network as a whole, from the point of view of reliability theory should be considered, for example, the ability of a sign or network to survive on the ground without changing location (without changing spatial coordinates) for a given period of time under certain conditions. In other words, the reliability of a geodetic sign or network as a whole is the probability that the sign or network in these conditions will fail to "work" until the end of a given time.