Irina Gamalij
Irina Gamalij has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Nataliia Shudra
Київський національний університет будівництва і архітектури
5 shared publications - Petro Chulanov
Київський національний університет будівництва та архітектури
5 shared publications - Tatiana Siroshtan5 shared publications
- Valeriy Gladilin
Department of Geodesy, Cartography and Land Management, Bila Tserkva National Agrarian University, Soborna pl. 8/1, 09117 Bila Tserkva, Kyivska oblast, Ukraine
5 shared publications - Tetyana Sviderska4 shared publications
- Anatolij Maznitskij2 shared publications
Latest Publications
- Open Access
- 23 February 2024
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 7,p. 365-381
ALGEBRAIC ADJUSTMENT OF MEASURED TRIANGLE ELEMENTS
It is difficult to align the measured elements of the triangle. A method of alignment using algebraic circles is proposed. If six elements are measured in a triangle: angles A, B, C, lengths of opposite sides a, b, c with mean square errors mA, mB, mC, ma, mb, mc, the values of the equalized elements must satisfy the requirements of the equations where D is the metric parameter of the triangle (the metric value through which the mathematical relationship between the sides and angles of the triangle is established), that is, the value of the diameter of the circle. If , which are found by formulas (1) and condition (2) is fulfilled, then this confirms the validity of the theorem of sines. In fact, it is a symmetrical set, because the number and composition of the upper indices corresponds to the number and composition of the lower indices, and this is a reflection of dimensions, since the triangle ABC has pairs of opposite elements: а- А; b- B; c- C. Let's construct the graph G Do of the diameter of the circle circumscribed around the aligned triangle, for which we will first construct the graphs G Di of the diameters of the circles circumscribed around the T-triangles, which are shown in fig. 1, and then combine them. Three vertices a, b, c form a "plane" - this is a metric field. The reflection of the metric field is the field of angular measurements - a "plane" defined by three points A, B, C. Note that for a measured triangle, the reflection of the metric field in the angular one is not unambiguous, so the first plane in fig. 1 is "inclined" to the second. After determining the most likely metric parameter Do of the triangle, it is possible to bring these planes into full correspondence. That is, Do is a "lens" [4],[8] with the help of which we obtain an unambiguous mapping of the metric field in the angular field and vice versa.
- 23 February 2024
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 7,p. 365-381
Open AccessALGEBRAIC ADJUSTMENT OF MEASURED TRIANGLE ELEMENTS
It is difficult to align the measured elements of the triangle. A method of alignment using algebraic circles is proposed. If six elements are measured in a triangle: angles A, B, C, lengths of opposite sides a, b, c with mean square errors mA, mB, mC, ma, mb, mc, the values of the equalized elements must satisfy the requirements of the equations where D is the metric parameter of the triangle (the metric value through which the mathematical relationship between the sides and angles of the triangle is established), that is, the value of the diameter of the circle. If , which are found by formulas (1) and condition (2) is fulfilled, then this confirms the validity of the theorem of sines. In fact, it is a symmetrical set, because the number and composition of the upper indices corresponds to the number and composition of the lower indices, and this is a reflection of dimensions, since the triangle ABC has pairs of opposite elements: а- А; b- B; c- C. Let's construct the graph G Do of the diameter of the circle circumscribed around the aligned triangle, for which we will first construct the graphs G Di of the diameters of the circles circumscribed around the T-triangles, which are shown in fig. 1, and then combine them. Three vertices a, b, c form a "plane" - this is a metric field. The reflection of the metric field is the field of angular measurements - a "plane" defined by three points A, B, C. Note that for a measured triangle, the reflection of the metric field in the angular one is not unambiguous, so the first plane in fig. 1 is "inclined" to the second. After determining the most likely metric parameter Do of the triangle, it is possible to bring these planes into full correspondence. That is, Do is a "lens" [4],[8] with the help of which we obtain an unambiguous mapping of the metric field in the angular field and vice versa.
- Open Access
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 276-292
THE PROBLEM OF RELIABILITY OF GEODESIC NETWORKS
В наш час теорія надійності широко використовується в будівельному виробництві, а також використовується і в області геодезії. Шляхом абстрагування її положення можна з успіхом перенести і на системи, які, здавалося б, не знаходяться в динамічному стані. Візьмемо, наприклад, пункти полігонометричної (нівелірної) мережі в місті. Здавалося б, що така мережа знаходиться в статичному стані, однак з плином часу вона зазнає змін, тобто вона знаходиться в непомітній динаміці і надійність її поступово знижується. Під надійністю в широкому сенсі цього слова розуміють здатність технічного пристрою (системи, мережі) до безперебійної (безвідмовної) роботи упродовж заданого проміжку часу у певних умовах. Такий проміжок часу зазвичай зумовлено часом виконання деякої задачі, яка здійснюється приладом чи системою і є частиною загальної операційної задачі в вирішенні топографо-геодезичних робіт. В даний час проблема надійності стає однією з вузлових проблем техніки та організації управління. Забезпечення надійної роботи всіх елементів системи – є першорядною важливістю.
- 26 December 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 6,p. 276-292
Open AccessTHE PROBLEM OF RELIABILITY OF GEODESIC NETWORKS
В наш час теорія надійності широко використовується в будівельному виробництві, а також використовується і в області геодезії. Шляхом абстрагування її положення можна з успіхом перенести і на системи, які, здавалося б, не знаходяться в динамічному стані. Візьмемо, наприклад, пункти полігонометричної (нівелірної) мережі в місті. Здавалося б, що така мережа знаходиться в статичному стані, однак з плином часу вона зазнає змін, тобто вона знаходиться в непомітній динаміці і надійність її поступово знижується. Під надійністю в широкому сенсі цього слова розуміють здатність технічного пристрою (системи, мережі) до безперебійної (безвідмовної) роботи упродовж заданого проміжку часу у певних умовах. Такий проміжок часу зазвичай зумовлено часом виконання деякої задачі, яка здійснюється приладом чи системою і є частиною загальної операційної задачі в вирішенні топографо-геодезичних робіт. В даний час проблема надійності стає однією з вузлових проблем техніки та організації управління. Забезпечення надійної роботи всіх елементів системи – є першорядною важливістю.
- Open Access
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 5,p. 286-305
PROPERTIES OF TRUE ERRORS OF GEODESIC MEASUREMENTS IN THE ALGEBRAIC CIRCLE
Істинні похибки можливо знайти коли ми знаємо істинне значення вимірюваної величини. В геодезичних вимірах та і в будь – яких інших вимірюваннях істинне значення вимірюваної величини невідоме, тому приймається якесь найбільш ймовірне значення цієї величини, сума ймовірних похибок повинна дорівнювати нулю, сума істинних похибок повинна дорівнювати нулю, тому необхідно дослідити ймовірні та істинні похибки в алгебраїчному колі. Розглядається новий метод оцінки точності вимірів він відрізняється від традиційних тим, що в результаті обробки вимірів однієї величини одержують не тільки загальну середню квадратичну похибку, а й середні квадратичні похибки всіх вимірів.
- 24 November 2023
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 5,p. 286-305
Open AccessPROPERTIES OF TRUE ERRORS OF GEODESIC MEASUREMENTS IN THE ALGEBRAIC CIRCLE
Істинні похибки можливо знайти коли ми знаємо істинне значення вимірюваної величини. В геодезичних вимірах та і в будь – яких інших вимірюваннях істинне значення вимірюваної величини невідоме, тому приймається якесь найбільш ймовірне значення цієї величини, сума ймовірних похибок повинна дорівнювати нулю, сума істинних похибок повинна дорівнювати нулю, тому необхідно дослідити ймовірні та істинні похибки в алгебраїчному колі. Розглядається новий метод оцінки точності вимірів він відрізняється від традиційних тим, що в результаті обробки вимірів однієї величини одержують не тільки загальну середню квадратичну похибку, а й середні квадратичні похибки всіх вимірів.
- Open Access
- 14 April 2023
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 83,p. 38-50
CALCULATION OF THE CORRELATION COEFFICIENT IN GEODETIC MEASUREMENTS
Пропонується формула для визначення коефіцієнтів кореляції, за якою при малій кількості вимірювань значення коефіцієнтів будуть більшими в порівнянні з величинами обчисленими за відомими формулами, тобто ці значення будуть менше зміщеними по відношенню до істинних величин коефіцієнтів кореляції. В геодезії взагалі обмежуються невеликою кількістю вимірювань, в фотограмметрії при взаємному орієнтуванні знімків стереопари в автоматичному режимі (на станції Дельта) при ідентифікації точок на лівому і правому знімках необхідно точно обчислювати значення коефіцієнтів кореляції, що дає можливість побудувати кращу фотограмметричну модель зображення місцевості.
- 14 April 2023
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 83,p. 38-50
Open AccessCALCULATION OF THE CORRELATION COEFFICIENT IN GEODETIC MEASUREMENTS
Пропонується формула для визначення коефіцієнтів кореляції, за якою при малій кількості вимірювань значення коефіцієнтів будуть більшими в порівнянні з величинами обчисленими за відомими формулами, тобто ці значення будуть менше зміщеними по відношенню до істинних величин коефіцієнтів кореляції. В геодезії взагалі обмежуються невеликою кількістю вимірювань, в фотограмметрії при взаємному орієнтуванні знімків стереопари в автоматичному режимі (на станції Дельта) при ідентифікації точок на лівому і правому знімках необхідно точно обчислювати значення коефіцієнтів кореляції, що дає можливість побудувати кращу фотограмметричну модель зображення місцевості.
- Open Access
- 30 May 2022
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 80,p. 115-130
CONSTRUCTION OF GEODESIC NETWORKS ON THE BASIS OF THE THEORY OF MARKOV ACCIDENTAL PROCESSES AND THE THEORY OF RELIABILITY
As mentioned above, the theory of reliability was mainly developed for technical devices. However, nowadays it is widely used in construction, and is also beginning to be used in geodesy. By abstracting its position can be successfully transferred to systems that do not seem to be in a dynamic state. Take, for example, the polygon metric network in the city. It would seem that such a network is in a static state, but over time it undergoes changes, ie it is in subtle dynamics and its reliability is gradually declining. Reliability in the broadest sense of the word means the ability of a technical device (system, network) to uninterrupted (trouble-free) operation for a specified period of time under certain conditions. This period of time is usually due to the time of a task. Which is carried out by a device or system and is part of the overall operational task. Currently, the problem of reliability is becoming one of the key problems of technology and management. Ensuring the reliable operation of all elements of the system is of paramount importance. Improving reliability requires special study and quantitative analysis of the phenomena associated with accidental failures of devices or systems. At this time, the theory of reliability has become a special science that makes extensive use of probable methods of examination. In the theory of reliability there are two types of failures: sudden and gradual. Consider sudden failures. Sudden device failures are understood as an instantaneous failure, which means that it cannot be used, and these failures occur at some random point in time. The reliability of the system depends on the composition and number of elements included in it, on the type of integration into the system and on the characteristics of each individual element. An element is to be understood as any device that is not subject to further disconnection, the reliability of which is specified or determined experimentally. By assembling such elements in different ways into systems, we will solve the problem of determining the reliability of the system depending on the reliability of its elements. The reliability of elements and systems is determined by numerical characteristics. We give some definitions of these characteristics for the element and the system as a whole. The reliability of the element is the probability that the element in certain conditions will work flawlessly over time, its probability is denoted. With increasing time, reliability usually decreases; with probability. In the geodetic literature, the term "reliability" is often used, which means the accuracy of the obtained results of geodetic measurements. However, the reliability of a geodetic sign or network as a whole, from the point of view of reliability theory should be considered, for example, the ability of a sign or network to survive on the ground without changing location (without changing spatial coordinates) for a given period of time under certain conditions. In other words, the reliability of a geodetic sign or network as a whole is the probability that the sign or network in these conditions will fail to "work" until the end of a given time.
- 30 May 2022
- Published by Kyiv National University of Construction and Architecture in Urban development and spatial planning
- No. 80,p. 115-130
Open AccessCONSTRUCTION OF GEODESIC NETWORKS ON THE BASIS OF THE THEORY OF MARKOV ACCIDENTAL PROCESSES AND THE THEORY OF RELIABILITY
As mentioned above, the theory of reliability was mainly developed for technical devices. However, nowadays it is widely used in construction, and is also beginning to be used in geodesy. By abstracting its position can be successfully transferred to systems that do not seem to be in a dynamic state. Take, for example, the polygon metric network in the city. It would seem that such a network is in a static state, but over time it undergoes changes, ie it is in subtle dynamics and its reliability is gradually declining. Reliability in the broadest sense of the word means the ability of a technical device (system, network) to uninterrupted (trouble-free) operation for a specified period of time under certain conditions. This period of time is usually due to the time of a task. Which is carried out by a device or system and is part of the overall operational task. Currently, the problem of reliability is becoming one of the key problems of technology and management. Ensuring the reliable operation of all elements of the system is of paramount importance. Improving reliability requires special study and quantitative analysis of the phenomena associated with accidental failures of devices or systems. At this time, the theory of reliability has become a special science that makes extensive use of probable methods of examination. In the theory of reliability there are two types of failures: sudden and gradual. Consider sudden failures. Sudden device failures are understood as an instantaneous failure, which means that it cannot be used, and these failures occur at some random point in time. The reliability of the system depends on the composition and number of elements included in it, on the type of integration into the system and on the characteristics of each individual element. An element is to be understood as any device that is not subject to further disconnection, the reliability of which is specified or determined experimentally. By assembling such elements in different ways into systems, we will solve the problem of determining the reliability of the system depending on the reliability of its elements. The reliability of elements and systems is determined by numerical characteristics. We give some definitions of these characteristics for the element and the system as a whole. The reliability of the element is the probability that the element in certain conditions will work flawlessly over time, its probability is denoted. With increasing time, reliability usually decreases; with probability. In the geodetic literature, the term "reliability" is often used, which means the accuracy of the obtained results of geodetic measurements. However, the reliability of a geodetic sign or network as a whole, from the point of view of reliability theory should be considered, for example, the ability of a sign or network to survive on the ground without changing location (without changing spatial coordinates) for a given period of time under certain conditions. In other words, the reliability of a geodetic sign or network as a whole is the probability that the sign or network in these conditions will fail to "work" until the end of a given time.