MSMohammad Abu Shahzer

Mohammad Abu Shahzer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mohammad Abu Shahzer has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Comparative analysis of flow physics in axial-flow pump predicted through the advanced unsteady numerical techniques

    by Duc-Anh Nguyen, Mohammad Abu Shahzer, Jin-Hyuk Kim

    Appropriate numerical methodologies should be selected for accurate, efficient computational simulations. This study is a comprehensive comparative analysis of the flow phenomena within an axial-flow pump that are predicted using numerical approaches: unsteady Reynolds-averaged Navier–Stokes (URANS), detached-eddy simulation (DES), and large-eddy simulation (LES). The shear stress transport k−ω turbulence model, combined with reattachment modification, is used for URANS prediction, while the wall-adapting local eddy-viscosity model for subgrid-scale (SGS) closure is used for LES. The grid resolution is verified to minimize the dependence of LES predictions on the SGS model. The numerical predictions are compared with the experimental data to assess the accuracy and reliability of the three approaches. The flow characteristics of the axial-flow pump involve cavitation and vortex structures generated by separation flows, tip leakage vortices (TLV), and trailing-edge (TE) vortices and their wake. In URANS, these phenomena are underestimated and have simple structures, limited spatial resolutions, and reduced temporal dependence. URANS predicts the TLV as a nearly straight structure, whereas DES and LES resolve it as an intricate spiral vortex. However, DES overpredicts vortex structures and vorticity intensities in certain regions. LES provides the most detailed and comprehensive depiction of flow phenomena, capturing numerous small-scale, highly convoluted vortex structures that illustrate their formation, evolution, and dissipation. URANS and DES exhibit limitations in resolving complex TE vortices, but LES effectively captures them as vortex shedding that gradually dissipates downstream. Additionally, LES reproduces the laminar–turbulent transition in near-wall flows, which cannot be achieved by URANS and DES.


  • Open Access

    Feasibility study of ultra-low-head hydro turbines for energy extraction from shallow waterways

    by Mohamed Murshid Shamsuddeen, Mohammad Abu Shahzer, Min-Su Roh, Jin-Hyuk Kim


  • Investigation of cavitating vortex rope instabilities and its suppression inside a Francis turbine model with Thoma number variation

    by Mohammad Abu Shahzer, Yong Cho, Mohamed Murshid Shamsuddeen, Jin-Hyuk Kim

    Cavitating vortex rope at part load (PL) condition at lower values of the Thoma number (σ) induces severe pressure fluctuation and efficiency reduction in a Francis turbine, which ultimately hinders continuous energy production. Installation of fins at draft tube (DT) can mitigate these instabilities and can safeguard the turbine operation with lower maintenance costs. The effect of fins on hydraulic performance and internal flow physics at PL condition with the variation of σ is examined in the present numerical investigation. For the two extreme opposite values of σ, the flow characteristics are predicted accurately for the turbine with and without fins by conducting transient simulations using ANSYS-CFX. The numerical findings on the structured and unstructured grid points are validated with the experimental results. The turbine's performance remains constant for higher values of Thoma numbers, and as the value decreases, the performance declines. The cavitation vortex rope formation inside the DT with fins is mitigated significantly at the minimum σ, while at the maximum value, the vortex rope with bubble generation is restricted. Compared to the without fin case, the swirl intensity is minimized remarkably (68%) with the presence of fins at the lowest σ. The maximum cavitation rate is manifested by the DT without fins, which is about 60% higher than the DT with fins. At minimum σ, extreme pressure pulsations are induced inside the DT without fins, which are reduced by 43% in the finned draft tube. Therefore, stable energy production is maximized with the installation of fins at both Thoma numbers.


  • Suppression of vortex rope formation and pressure fluctuation using anti-swirl fins in a Francis turbine model at part load condition with cavitation inception point

    by Mohammad Abu Shahzer, Seung-Jun Kim, Yong Cho, Jin-Hyuk Kim

    Vortex rope formation at part load (PL) with cavitation inception causes pressure fluctuations inside the draft tube (DT) of a Francis turbine which may fail the turbine due to resonance and erosion. The pressure surge can be minimized by using anti-swirl fins which ensure safe turbine operation. The present study examines the effect of fin sizes and locations on the internal flow characteristics of the Francis turbine and predicts its adverse effect on the pressure surge. Three cases are investigated in which internal flow physics are compared among DTs with longer fins, shorter fins, and no fins. At the cavitation inception point under PL conditions, the characteristics are thoroughly studied numerically using ANSYS-CFX with structured and unstructured grids. Cavitation and PL conditions are designated by Thoma number 0.266 and guide vane angle 16° . Numerical methodology is then verified by an experiment based on International Standard (IEC 60193). The vortex rope occurrence is suppressed using fins on the DT periphery and longer fins that are extended up to the elbow exhibit the lowest strength of the vortex rope. Maximum pressure recovery inside the DT is achieved using longer fins. The swirl intensity is remarkably reduced by about 94% with longer fins. The pressure peak of low frequency is about 60% suppressed using longer fins. The PL and cavitation-induced instabilities and vibrations are significantly mitigated by longer fins, while shorter fins also moderately minimize it. Hence, energy production is preferable with longer fins because of the safe and stable turbine function.


  • A comprehensive investigation of vortex-induced vibrations and flow-induced rotation of an elliptic cylinder

    by Mohammad Abu Shahzer, Syed Fahad Anwer, Saleem Anwar Khan, Mohammad Shoaib Khan, Abdullah Algethami, Mishal Alsehli

    This work finds its motivation in heat exchanger design and flow control. Flow-induced vibration is studied numerically for combined vortex-induced vibrations and vortex-induced rotations of a horizontally positioned elliptic cylinder. The aspect ratio is taken as 2, and the value of reduced velocities (Ured ) considered for the present simulation is between 2 and 12. The body can have to and fro motions in a transverse (y) direction, in-line (x) direction as well as in azimuthal (θ ) direction, which provides three degrees of freedom (DOF) to the body. It is found that for one-DOF (y-direction only) and two-DOF (y and x directions) cases, lock-in regions are the same while it is wider for the case of the three-DOF system. With the rotational DOF, y-directional motion is amplified and when it is compared with the one-DOF and two-DOF cases, difference in peak amplitude is about 30%. The rotational response reaches a maximum value within the synchronization regime, and the frequency behavior of rotational and transverse oscillations is showing the same characteristics. The phase difference is plotted to check their synchronization with respective forces and moments. For all DOFs and Ured , synchronized or desynchronized regions, 2S mode of vortex shedding was observed. For one-DOF and two-DOF cases, the transverse vibrational frequency ratio (fy/fn ) becomes equal to unity for the range 3.75≤Ured≤5 . For three-DOF, fy/fn and rotational frequency ratio (fR/fn) become close to the unity for 3.75≤Ured≤6 . The three-DOF system shows smaller wake width and vortex formation length whereas the vortex strength is maximum.