HAHemant Agiwal

Hemant Agiwal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hemant Agiwal has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Radius of Contact During Friction Surfacing of Stainless Steel 304L: Effect of Spindle Speed and Rod Diameter

    by Hemant Agiwal, Hwasung Yeom, Kumar Sridharan, Shiva Rudraraju, Frank E. Pfefferkorn

    The “radius of contact” or the “real-rotational contact plane,” has been increasingly mentioned terminology in friction surfacing. However, the fundamental understanding of the flow dynamics behind this phenomenon is still very limited. The goal of this study was to understand the influence of spindle speed and consumable rod diameter on the flow dynamics and the radius of contact during friction surfacing of 304L stainless steel over a substrate of the same material. Friction surfacing was performed using consumable rods with diameters of 4.76 mm, 9.52 mm, and 12.7 mm while using spindle speeds from 1500 rpm to 20,000 rpm. The impact of spindle speed on deposition morphology, including the radius of contact, was studied. The radius of contact was calculated empirically and was found to be inversely proportional to the tangential velocity of the rod. The coupling between flow stresses and localized forces is hypothesized to be the key factor behind the variation of the radius of contact with processing conditions.


  • Numerical Investigation Into the Influence of Alloy Type and Thermo-Mechanics on Void Formation in Friction Stir Welding of Aluminum Alloys

    by Mohammad Ali Ansari, Hemant Agiwal, Daniel Franke, Michael R. Zinn, Frank E. Pfefferkorn, Shiva Rudraraju

    This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18, were investigated under varying traverse speeds. The choice of aluminum alloys enables the investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are as follows: (1) the predicted stir zone and void morphology are in good agreement with the experimental observations, (2) the temperature and plastic strain rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) the material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this study provide a framework for understanding material flow under different process conditions in aluminum alloys and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.


  • Open Access

    Numerical Investigation into the Influence of Alloy Type and Thermo-mechanics on Void Formation in Friction Stir Welding of Aluminium Alloys

    by Mohammad Ali Ansari, Hemant Agiwal, Daniel Franke, Mike Zinn, Frank E. Pfefferkorn, Shiva Rudraraju

    This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18 were investigated under varying traverse speeds. The choice of aluminum alloys enables investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are: (1) The predicted stir zone and void morphology are in good agreement with the experimental observations, (2) The temperature and plastic strain-rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) The material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this work provide a framework for understanding material flow under different process conditions in aluminum alloys, and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.


  • Friction surfacing and cold spray deposition for surface crack repair in austenitic stainless steels

    by Hemant Agiwal, Hwasung Yeom, Nicholas Pocquette, Kumar Sridharan, Frank E. Pfefferkorn


  • Material flow visualization during friction stir welding using high-speed X-ray imaging

    by Hemant Agiwal, Mohammad Ali Ansari, Daniel Franke, Patrick Faue, Samuel J. Clark, Kamel Fezzaa, Shiva Rudraraju, Michael Zinn, Frank E. Pfefferkorn


  • Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

    by Hemant Agiwal, Christian Baumann, Stephan Krall, Hwasung Yeom, Kumar Sridharan, Friedrich Bleicher, Frank E. Pfefferkorn

    The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.


  • Open Access

    Microstructure and Corrosion Behavior of Friction Surfaced 304L Austenitic Stainless Steels

    by Hemant Agiwal, Kumar Sridha, Frank Pfefferkorn, Hwasung Yeom

    Friction surfacing is a solid-state deposition process that provides microstructural and mechanical property benefits over fusion-based deposition methods as a result of the lower heat input and hot working. The study examines microstructure and corrosion properties for friction surfaced 304L stainless steel consumable rods on 304L stainless steel substrates. Microstructural characterization revealed fine-grained microstructure with distributed strain-induced martensite and high residual compressive stresses. Corrosion studies of friction surfaced specimens were carried out by exposure to FeCl3 and MgCl2 solutions per ASTM G48 and ASTM G36 standards, respectively. The corrosion tests showed friction surfacing led to shallower and smaller pits than the uncoated substrate, however, the pit number density was higher in the friction surfaced specimens. The microstructural transformations during friction surfacing are beneficial to mitigating pitting corrosion and potentially chloride-induced stress corrosion cracking (CISCC).

  • Open Access

    Novel Correlations Between Process Forces and Void Morphology for Effective Detection and Minimization of Voids During Friction Stir Welding

    by Mohammad Ali Ansari, Hemant Agiwal, Mike Zinn, Frank Pfefferkorn, Shiva Rudraraju

    Sub-surface voids and material heterogeneities resulting from the friction stir welding (FSW) process often necessitate post-weld inspection to ensure the quality of weld obtained from this solid-state welding process. In this context, in-process void detection techniques can potentially help in optimizing the process conditions and thereby reduce expensive and time-consuming post-process inspection of welds. Current in-process void detection techniques rely on approaches that try to directly correlate the part-scale welding quality to void formation, without a fundamental understanding of the underlying mechanics and materials physics that modulate void evolution. In this work, we demonstrate an effective in-process numerical technique that uses process force signals to detect volumetric void formation and connect the variations in the force signals to interactions between the tool probe and the underlying material voids. Our approach relies on a high-fidelity finite element analysis simulation of the FSW process and on correlation of numerically obtained process force signals with the corresponding void structures. This correlation is obtained in the phase-space relating in-plane reaction forces on the tool to the tool rotation angle. We focus on the interactions of the tool geometry and tool motion with the surrounding material undergoing plastic deformation and deduce novel insights into various correlations of tool motion and void formation. Through this approach, we can identify tool-related process conditions that can be optimized to minimize void formation and demonstrate a potential in situ force-based void monitoring method that links to the underlying plastic flow and void structures during the FSW process.


  • Investigation of multilayer coating of EN AW 6060 - T66 using friction surfacing

    by Stephan Krall, Christian Baumann, Hemant Agiwal, Friedrich Bleicher, Frank Pfefferkorn

    The objective of this research is to investigate observable process changes during multi-layer friction surfacing of EN AW 6060 aluminum, whether for repair, remanufacturing, or new part manufacturing. In this study, friction surfacing was performed with a 10-mm-diameter rod of EN AW 6060...


  • Open Access

    Cold Spray Process to Mitigate Potential Stress-Corrosion Cracking in Used Nuclear Fuel Storage Canisters

    by Nicholas Pocquette, Hwasung Yeom, Hemant Agiwal, Frank Pfefferkorn, Kumar Sridharan, Kenneth Ross, John Kessler, Gary Cannel

    Cold spray deposition is being investigated for mitigation of chloride-induced stress corrosion cracking (CISCC) in dry cask storage systems (DCSS) for spent nuclear fuel. Welded regions of austenitic stainless-steel canisters in DCSS are under tensile stress and susceptible to environmental chloride corrosion, which can potentially lead to the formation of CISCC. The low thermal input and high throughput nature of cold spraying make it a viable repair and mitigation option for managing potential CISCC. Cold spray coatings are under compressive stress and act as a barrier in Cl-rich environments. Characterization data including microstructure, hardness, and corrosion resistance are presented for cold spray coatings on stainless steel substrates.