Lingyun Zeng
Research Subjects
Lingyun Zeng has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Christos Bergeles
School of Biomedical Engineering & Imaging Sciences, King’s College London, London, UK
3 shared publications - Seyedmohammadhadi M. Hadi Sadati
School of Engineering and Materials Science, Queen Mary University of London, London, U.K.
2 shared publications Alejandro Chavez-Badiola
1 shared publication- Baibo Wu
Shanghai Jiao Tong University School of Mechanical Engineering 800 Dongchuan Road, Shanghai 200240 , China
1 shared publication - Chuanxiang Zhu
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China
1 shared publication Gerardo Mendizabal-Ruiz
1 shared publication
Latest Publications
- 26 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 42 (15523098) , 2439-2458
6-D Tip Wrench Estimation for Continuum Robots: A Koopman-UKF-Wrench Decomposition Approach
This paper presents a method for comprehensive 6D estimation of tip wrench for generally deflected static elastic rods. Current methods for load estimation are restricted to estimating lateral (point or distributed) forces for (quasi-)planar deformation; estimation of tangential force and moment, i.e., the full 6D wrench, remains largely unreliable due to the ill-posed nature of the problem. To address this challenge, this paper begins by proposing a high-fidelity static rod model that leverages Koopman Operator theory. Building on this model and utilizing shape feedback, a computationally efficient three-step wrench estimator is proposed: (i) a Koopman-UKF local moment observer, (ii) a static equilibrium solver, and (iii) a rod model propagator. Then, a 2D wrench screw system, identified as the insensible wrench in the initial estimation, elucidates error sources and informs strategies to enhance accuracy by incorporating additional feedback, such as the rod tip material frame and base axial force. Ultimately, the framework delivers accurate 6D tip wrench estimation with quantified uncertainty. Simulation and experimental evaluations validate its effectiveness, demonstrating mean errors of $53.14\,$mN (1.94%) and $2.65\,$mNm (7.18%) for a $159\,$mm-long Nitinol tube undergoing complex out-of-plane deformations, outperforming three replicated state-of-the-art methods. Additionally, its applicability to more complex continuum robots is demonstrated through load estimation on a Parallel Continuum Robot.
- 26 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 42 (15523098) , 2439-2458
6-D Tip Wrench Estimation for Continuum Robots: A Koopman-UKF-Wrench Decomposition Approach
This paper presents a method for comprehensive 6D estimation of tip wrench for generally deflected static elastic rods. Current methods for load estimation are restricted to estimating lateral (point or distributed) forces for (quasi-)planar deformation; estimation of tangential force and moment, i.e., the full 6D wrench, remains largely unreliable due to the ill-posed nature of the problem. To address this challenge, this paper begins by proposing a high-fidelity static rod model that leverages Koopman Operator theory. Building on this model and utilizing shape feedback, a computationally efficient three-step wrench estimator is proposed: (i) a Koopman-UKF local moment observer, (ii) a static equilibrium solver, and (iii) a rod model propagator. Then, a 2D wrench screw system, identified as the insensible wrench in the initial estimation, elucidates error sources and informs strategies to enhance accuracy by incorporating additional feedback, such as the rod tip material frame and base axial force. Ultimately, the framework delivers accurate 6D tip wrench estimation with quantified uncertainty. Simulation and experimental evaluations validate its effectiveness, demonstrating mean errors of $53.14\,$mN (1.94%) and $2.65\,$mNm (7.18%) for a $159\,$mm-long Nitinol tube undergoing complex out-of-plane deformations, outperforming three replicated state-of-the-art methods. Additionally, its applicability to more complex continuum robots is demonstrated through load estimation on a Parallel Continuum Robot.
- 8 March 2023
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 15 (3) , 1-24
Kinetostatic Modeling of Continuum Delta Robot With Variable Curvature Continuum Joints
Continuum robots have attracted lots of attention due to their structural compliance, manipulation dexterity, and design compactness. To extend the application scenarios, a slender continuum robot, the CurviPicker, was developed for low-load medium-speed pick-and-place tasks in a previous study. To improve the payload capacity and positioning accuracy of the CurviPicker, a novel Continuum Delta Robot (CDR) was then proposed with three dual-continuum-joint translators in a preliminary investigation. However, the initial version of the CDR did not fully utilize the bending ranges of its continuum joints. What's more, while being modeled using the constant curvature assumption for the continuum joints, the CDR shows lowered positioning accuracy for heavier objects, as the CDR's continuum joints diverge from the assumed constant curvature shapes. In this paper, the design of the CDR was re-optimized to enable wider bending ranges of the continuum joints (> 90 °) to generate enlarged workspace, taking into considerations several possible structural interferences. Furthermore, a kinetostatic model is derived based on the Cosserat rod theory to reduce the positioning errors caused by the external loads. The experimental result showed that the workspace is enlarged to approximately 9.47 × 107 mm3 compared with the volume of 6.57 × 107 mm3 of the initial version. Within this enlarged workspace, the average positioning error with a 1000-gram load was reduced to 1.93 mm, compared with 4.43 mm obtained by the previous constant curvature assumption.
- 8 March 2023
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 15 (3) , 1-24
Kinetostatic Modeling of Continuum Delta Robot With Variable Curvature Continuum Joints
Continuum robots have attracted lots of attention due to their structural compliance, manipulation dexterity, and design compactness. To extend the application scenarios, a slender continuum robot, the CurviPicker, was developed for low-load medium-speed pick-and-place tasks in a previous study. To improve the payload capacity and positioning accuracy of the CurviPicker, a novel Continuum Delta Robot (CDR) was then proposed with three dual-continuum-joint translators in a preliminary investigation. However, the initial version of the CDR did not fully utilize the bending ranges of its continuum joints. What's more, while being modeled using the constant curvature assumption for the continuum joints, the CDR shows lowered positioning accuracy for heavier objects, as the CDR's continuum joints diverge from the assumed constant curvature shapes. In this paper, the design of the CDR was re-optimized to enable wider bending ranges of the continuum joints (> 90 °) to generate enlarged workspace, taking into considerations several possible structural interferences. Furthermore, a kinetostatic model is derived based on the Cosserat rod theory to reduce the positioning errors caused by the external loads. The experimental result showed that the workspace is enlarged to approximately 9.47 × 107 mm3 compared with the volume of 6.57 × 107 mm3 of the initial version. Within this enlarged workspace, the average positioning error with a 1000-gram load was reduced to 1.93 mm, compared with 4.43 mm obtained by the previous constant curvature assumption.
- 14 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 5671-5678
Real-Time Dynamics of Concentric Tube Robots With Reduced-Order Kinematics Based on Shape Interpolation
Concentric tube robots (CTRs) are catheter-like robots that can navigate anatomical lumen to reach surgical targets that are deep inside the body. While CTRs have been extensively studied in quasi-static conditions, unique robot behaviours such as hysteresis and snapping, i.e. the sudden release of elastic energy accumulated due to robot tubes’ twisting, are relatively underexplored. For the first time, we present a real-time dynamic model that captures both snapping and hysteresis for CTRs with arbitrary number of tubes and precurved shape. We pursue Reduced-Order Modelling (ROM) with shape interpolation-based kinematics to reach a system of minimal states appropriate for ultimate real-time non-linear control. We implement and incorporate our theoretical contributions within the open-source modelling software package TMTDyn and make them available to the robotics community. Our method is experimentally verified using a highly curved CTR that undertakes complex 3D dynamic motions, for the first time predicting similar pathways during highly nonlinear snapping motions, which is when classical models fail, while preserving the state-of-the-art modeling accuracy of $\approx$ 6% mean error.
- 14 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 5671-5678
Real-Time Dynamics of Concentric Tube Robots With Reduced-Order Kinematics Based on Shape Interpolation
Concentric tube robots (CTRs) are catheter-like robots that can navigate anatomical lumen to reach surgical targets that are deep inside the body. While CTRs have been extensively studied in quasi-static conditions, unique robot behaviours such as hysteresis and snapping, i.e. the sudden release of elastic energy accumulated due to robot tubes’ twisting, are relatively underexplored. For the first time, we present a real-time dynamic model that captures both snapping and hysteresis for CTRs with arbitrary number of tubes and precurved shape. We pursue Reduced-Order Modelling (ROM) with shape interpolation-based kinematics to reach a system of minimal states appropriate for ultimate real-time non-linear control. We implement and incorporate our theoretical contributions within the open-source modelling software package TMTDyn and make them available to the robotics community. Our method is experimentally verified using a highly curved CTR that undertakes complex 3D dynamic motions, for the first time predicting similar pathways during highly nonlinear snapping motions, which is when classical models fail, while preserving the state-of-the-art modeling accuracy of $\approx$ 6% mean error.