ANAditya Sukma Nugraha

Aditya Sukma Nugraha

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Aditya Sukma Nugraha has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Temperature optimization model to inhibit zero-order kinetic reactions

    by Januardi Januardi, Aditya Sukma Nugraha

    Originally, the Arrhenius parameters were used to estimate the rate of chemical reactions. This article aims to develop the optimal temperature to inhibit specific zero-order kinetic reactions. The model extends the use of the Arrhenius equation and heat capacity modeling to derive the optimal temperature solution. Specifically, the Arrhenius equation, which connects temperature to reaction rates, and the heat equation are formulated to create a comprehensive heat accumulation model. Analytical modeling is utilized through a derivative process to provide optimization. According to a case study of carotene oxidation, the derivative solution proposes −1.73 °C and can extend the reaction time by 206,160.29 days compared to a solution with no temperature change. The derivative solution also offers higher advantages in practical application than setting the lowest temperature limit due to the high initial energy requirement. The temperature derivative solution exhibits a global optimum property because of its high heat accumulation and slower kinetic reactions. These slower kinetic reactions can prevent reactant substances from deteriorating, making them valuable for maintaining a chemical’s shelf life. The temperature solutions offer valuable insights for devising an effective temperature strategy to inhibit specific chemical processes and verifying the relationship between temperature and heat accumulation with curvature.


  • Fabrication and characterization of PZT / PVDF composite films for force sensor applications

    by Suprapto, Yung Ting, Hariyanto Gunawan, Edwar Yazid, Aditya Sukma Nugraha, Budi Azhari, M Luthfi Ramadiansyah, M Fathul Hikmawan, Jubaidah

    This study explored the impact of hot press parameters on lead zirconate titanate (PZT)/poly(vinylidene fluoride) (PVDF) composite films designed for force‐sensing applications. The systematic fraction (PZT/PVDF), pressure, temperature, and time during hot pressing processes are subject to variation. The focus is on the resulting composite film thickness and its subsequent influence on the piezoelectric properties, which are essential for the performance of force sensors. The present study investigated the characteristics and performance of PZT/PVDF composite films with fraction ratios 2/5, 5/5, and 7/3 and hot pressure of 10, 40, and 60 MPa and temperature at 150 °C for 2 h. The characterization of these films was conducted using X‐ray diffraction, Fourier transform infrared spectroscopy, atomic force microscopy, and scanning electron microscopy. The piezoelectric properties ( d 33 and d 31 ) were measured using impact and extraction tests to evaluate the performance of films with applied forces. The results show that the highest piezoelectric coefficients ( d 33 and d 31 ) were determined to be 35.8 and 12.60 pC N −1 , with fraction ratios of 7/3 and 2/5. The study revealed a positive correlation between the PZT/PVDF ratio and sensitivity, indicating that an increase in the ratio leads to an increase in sensitivity. Conversely, a negative relationship was observed between the impact load and the sensor sensitivity, suggesting that an increase in the impact load results in a sensitivity decrease. The results of this work demonstrate the great potential of piezoelectric PZT/PVDF composite films in force sensors for small load applications. © 2024 Society of Chemical Industry.


  • Local analysis of crystalline phases and properties of poly(vinylidene fluoride) electrospun composites with BaTiO3 nanorods

    by Aditya Sukma Nugraha, Chen Chia Chou, Bramantyo Bayu Aji

    This study investigated the influence of barium titanate nanorods (BT rods) on the properties and phase formation of poly(vinylidene fluoride) (PVDF) nanofibers of composite membranes created using the electrospinning technique. The primary objective was to assess the effect of varying BT nanorod concentrations on the membrane properties. The result shows that inserting BT rods into PVDF increases β‐phase content, which, with an optimal concentration of BT rods, affects the activation energy of thermal degradation resulting in the highest β‐phase content and the lowest activation energy at 3% BT content. Moreover, the electrical output of the samples was measured. Using a ball‐drop test, the sample containing 3 wt% BT rods exhibited the highest output voltage, reaching 1.64 V. The BT rods play a significant role in promoting the β‐phase PVDF molecular chain formation, acting as the polar phase in PVDF and aligning with the polarization direction of the BT rods. According to high‐resolution transmission electron microscopy investigations, crystalline phases of PVDF are strongly correlated with the surface charges of perovskite BT rods. The occurrence of charge on the BT rods significantly contributes to fostering the development of the β‐phase PVDF molecular chain. It essentially performs the function of the polar phase within the PVDF, aligning itself in accordance with the polarization direction inherent to the BT rods. In conclusion, this study demonstrates the potential of incorporating BT rod polar surfaces to interact with PVDF chain dipole moments, promoting β‐phase formation. © 2023 Society of Industrial Chemistry.


  • Effects of applied voltage on the morphology and phases of electrospun poly(vinylidene difluoride) nanofibers

    by Aditya Sukma Nugraha, Chen Chia Chou, Pin Hsun Yu, Kun‐Lin Lin

    Electrospinning is a simple and flexible process in continuous fiber fabrication. We investigate the effect of applied voltage on morphology and phases of poly(vinylidene difluoride) nanofibers obtained using the electrospinning technique. Quantitative and qualitative analyses were performed employing multiple characterizations such as Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD) and high‐resolution transmission electron microscopy (HRTEM). The fiber diameter, affected by the spinning jet's deformation, has non‐uniform distribution at low voltages (10–16 kV) and is uniform at higher voltages (20 kV). Fiber uniformity developed due to the increased tension, which shrank the Taylor cone. The highest electroactive fraction () of phases was obtained for the smallest diameter fiber with an average diameter of 110 nm at an applied voltage of 20 kV. FTIR spectroscopy and XRD results indicate that the electric field raises the amount of phase to 74% at the present working parameters. HRTEM analysis revealed that the crystallites are very small, with α‐phase showing a size of around 10 nm and β‐phase is only of nanometric scale. Results also show that the c‐axis of α‐phase crystallites had a preferred orientation along the fiber axis. On the other hand, the c‐axis of β‐phase had a preferred orientation perpendicular to the fiber axis, implying that the direction of crystal growth for the α‐phase and β‐phase was different. © 2022 Society of Industrial Chemistry.