Jong Wan Jo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jong Wan Jo has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Kang-Yoon Lee
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
9 shared publications - YoungGun Pu
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
5 shared publications - Yeonjae Jung
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon-si, South Korea
4 shared publications - Jun-Eun Park
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
3 shared publications - Keum Cheol Hwang
Sungkyunkwan University
3 shared publications - Youngoo Yang
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea
3 shared publications
Latest Publications
- 28 January 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (11) , 5221-5230
A Design of 30 MS/s 70.39 dB SNDR, 12‐Bit Charge‐Sharing ADC for Ultrasonic Imaging Applications
This paper presents a 12‐bit, high speed charge‐sharing analog‐to‐digital converter (ADC), targeting low area and low power in wide bandwidth integrated RF transceivers for ultrasound diagnostic medical devices. The ADC comprises charge sharing digital‐to‐analog converter (DAC) with unit array capacitors with low threshold voltage devices for small area and low on resistance respectively. The circuit uses sample and hold circuit based on bootstrapping to reduce the effect of third harmonic. The dynamic latch comparator with adaptive power control improves the power efficiency. Furthermore, the asynchronous SAR logic delay cells are digitally controlled to minimize the power consumed by the digital part. The ADC achieves an effective number of bits (ENOB) of 11.40 bits and signal to noise distortion ratio (SNDR) of 70.39 dB at the input frequency of 500 kHz. The designed ADC is implemented with a 0.13 μm CMOS process occupying an area of 1600 μm × 505 μm. The designed SAR ADC draws 0.8 mA current per channel at a sampling rate of 30 MSPS when operated at a 1.5 V power supply.
- 28 January 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (11) , 5221-5230
A Design of 30 MS/s 70.39 dB SNDR, 12‐Bit Charge‐Sharing ADC for Ultrasonic Imaging Applications
This paper presents a 12‐bit, high speed charge‐sharing analog‐to‐digital converter (ADC), targeting low area and low power in wide bandwidth integrated RF transceivers for ultrasound diagnostic medical devices. The ADC comprises charge sharing digital‐to‐analog converter (DAC) with unit array capacitors with low threshold voltage devices for small area and low on resistance respectively. The circuit uses sample and hold circuit based on bootstrapping to reduce the effect of third harmonic. The dynamic latch comparator with adaptive power control improves the power efficiency. Furthermore, the asynchronous SAR logic delay cells are digitally controlled to minimize the power consumed by the digital part. The ADC achieves an effective number of bits (ENOB) of 11.40 bits and signal to noise distortion ratio (SNDR) of 70.39 dB at the input frequency of 500 kHz. The designed ADC is implemented with a 0.13 μm CMOS process occupying an area of 1600 μm × 505 μm. The designed SAR ADC draws 0.8 mA current per channel at a sampling rate of 30 MSPS when operated at a 1.5 V power supply.
- Open Access
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 6, 110-119
Design of a High Efficiency Bi-Directional Four-Switch Buck-Boost Converter With HV Gate Driver for Multi-Cell Battery Power Bank Applications
This paper presents a bidirectional Four-Switch Buck-Boost (FSBB) converter with a high-voltage (HV) gate driver for use in power bank applications. The proposed FSBB is also integrated into this converter for increased efficiency. Thus, the proposed buck-boost converter can reduce conduction loss over a wide input voltage range by reducing the on-resistance of external MOSFETs using a gate source voltage (VGS) of 5V or 10V. The chip to be examined in this study is fabricated using a 130 nm 1P5M bipolar-CMOS-DMOS HV process with laterally diffused MOSFET (LDMOS) options to have a die size of 2.7 x 2.7 mm2. The proposed architecture is found to achieve a maximum output power level of 40W. The measurement results show that the maximum efficiencies at gate-source voltages (VGS) of 5V and 10V are 96.67% and 98.15%, respectively.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 6, 110-119
Open AccessDesign of a High Efficiency Bi-Directional Four-Switch Buck-Boost Converter With HV Gate Driver for Multi-Cell Battery Power Bank Applications
This paper presents a bidirectional Four-Switch Buck-Boost (FSBB) converter with a high-voltage (HV) gate driver for use in power bank applications. The proposed FSBB is also integrated into this converter for increased efficiency. Thus, the proposed buck-boost converter can reduce conduction loss over a wide input voltage range by reducing the on-resistance of external MOSFETs using a gate source voltage (VGS) of 5V or 10V. The chip to be examined in this study is fabricated using a 130 nm 1P5M bipolar-CMOS-DMOS HV process with laterally diffused MOSFET (LDMOS) options to have a die size of 2.7 x 2.7 mm2. The proposed architecture is found to achieve a maximum output power level of 40W. The measurement results show that the maximum efficiencies at gate-source voltages (VGS) of 5V and 10V are 96.67% and 98.15%, respectively.
- Open Access
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 50032-50042
A Design of a 100-MHz Fully Integrated Digital Pulse Width Modulation Three-Level Buck Converter Using Package Bond-Wire Inductor
This paper presents a fully integrated digital pulse-width-modulation three-level DC–DC buck converter. An internal switching frequency of 100 MHz is selected to minimize the value of passive components, and the package bond-wire based inductor is selected. In the integrated voltage regulator, a three-level structure is used to reduce the output voltage ripple, and Digital pulse width modulation (DPWM) is employed to achieve efficient current and voltage control. This digitally configured control scheme is robust against external environmental factors, such as process, voltage, and temperature variations, and also achieves a fast load transient time. The proposed circuit is fabricated using a 130-nm BCDMOS process, and it can regulate the 5-V input voltage to the output voltage range of 3.3–3.7 V. The three-level buck converter with an active area of 1.035 mm2 shows a power conversion efficiency of 72.4% under the load current of 200 mA.
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 50032-50042
Open AccessA Design of a 100-MHz Fully Integrated Digital Pulse Width Modulation Three-Level Buck Converter Using Package Bond-Wire Inductor
This paper presents a fully integrated digital pulse-width-modulation three-level DC–DC buck converter. An internal switching frequency of 100 MHz is selected to minimize the value of passive components, and the package bond-wire based inductor is selected. In the integrated voltage regulator, a three-level structure is used to reduce the output voltage ripple, and Digital pulse width modulation (DPWM) is employed to achieve efficient current and voltage control. This digitally configured control scheme is robust against external environmental factors, such as process, voltage, and temperature variations, and also achieves a fast load transient time. The proposed circuit is fabricated using a 130-nm BCDMOS process, and it can regulate the 5-V input voltage to the output voltage range of 3.3–3.7 V. The three-level buck converter with an active area of 1.035 mm2 shows a power conversion efficiency of 72.4% under the load current of 200 mA.
- Open Access
- 14 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 35922-35932
A Design of High-Efficiency RF/Solar/ Triboelectric/Electromagnetic Energy Harvesting System
This paper presents a comprehensive exploration of a Hybrid Energy Harvesting System designed to harvest energy from diverse sources, including 2.4 GHz and 5.8 GHz RF energy, electromagnetic (EM) energy, solar energy, and triboelectric energy. The proposed converter operates within a wide input voltage range, maximizing efficiency and stability. A reconfigurable RF-DC converter is used for both 2.4 GHz and 5.8 GHz frequencies to achieve high power conversion efficiency at low input power level. A maximum of 52 % and 44.8 % PCE is achieved at −14 dBm and −2 dBm respectively. Electromagnetic rectifier produces an output voltage of 1 V with a PCE of 95.6 % which operates with a 15 Hz input frequency. The voltage of the tribo rectifier is limited by the limiter circuit to 2.5 V with a PCE of 96 % concerning load current. A voltage combiner is used to combine all these harvested voltages and pass them to the buckboost DC-DC converter. This hybrid energy harvesting system is designed and fabricated in 180 nm bipolar-CMOSDMOS (BCD) technology with an active area of 2.8mm $\times 2.5$ mm. The buck-boost DC-DC converter incorporated into our hybrid energy harvesting system achieves an impressive peak Power Conversion Efficiency (PCE) of 95 %. This innovative system integrates EM, solar, triboelectric, and RF energy harvesters, collectively ensuring a reliable power source. The ultimate goal is to deliver a steady 5 V DC voltage, skillfully regulated by the buck-boost DC-DC converter.
- 14 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 35922-35932
Open AccessA Design of High-Efficiency RF/Solar/ Triboelectric/Electromagnetic Energy Harvesting System
This paper presents a comprehensive exploration of a Hybrid Energy Harvesting System designed to harvest energy from diverse sources, including 2.4 GHz and 5.8 GHz RF energy, electromagnetic (EM) energy, solar energy, and triboelectric energy. The proposed converter operates within a wide input voltage range, maximizing efficiency and stability. A reconfigurable RF-DC converter is used for both 2.4 GHz and 5.8 GHz frequencies to achieve high power conversion efficiency at low input power level. A maximum of 52 % and 44.8 % PCE is achieved at −14 dBm and −2 dBm respectively. Electromagnetic rectifier produces an output voltage of 1 V with a PCE of 95.6 % which operates with a 15 Hz input frequency. The voltage of the tribo rectifier is limited by the limiter circuit to 2.5 V with a PCE of 96 % concerning load current. A voltage combiner is used to combine all these harvested voltages and pass them to the buckboost DC-DC converter. This hybrid energy harvesting system is designed and fabricated in 180 nm bipolar-CMOSDMOS (BCD) technology with an active area of 2.8mm $\times 2.5$ mm. The buck-boost DC-DC converter incorporated into our hybrid energy harvesting system achieves an impressive peak Power Conversion Efficiency (PCE) of 95 %. This innovative system integrates EM, solar, triboelectric, and RF energy harvesters, collectively ensuring a reliable power source. The ultimate goal is to deliver a steady 5 V DC voltage, skillfully regulated by the buck-boost DC-DC converter.
- 17 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 5270-5283
A 92.7% Peak Efficiency Self-Starting Boost Converter With MPPT and Phase Frequency Detector Based Multi Current Detector for Energy Harvesting Systems With a Minimum Input Source Impedance of 1 Ω
This article presents a boost converter based on a maximum power point tracking (MPPT) circuit, and a multicurrent detector (MCD), an offset cancellation circuit to achieve high efficiency over a wide range of input power. The proposed boost converter employs an MPPT design for adaptive on-time operation, which adjusts the on-time width to achieve maximum efficiency depending on the input voltage. In addition, a phase frequency detector-based offset cancellation method is proposed to minimize power loss by accurately sensing the current detector, thereby transferring power. Therefore, the proposed method achieves a significant efficiency improvement of up to 10 % by implementing high-precision offset cancellation with an offset level of approximately$5~\mu $ A, which is significantly lower than the conventional MCD offset of over 60 mA of maximum offset current level. The proposed boost converter fabricated in a 130 nm Bipolar-CMOS-DMOS (BCD) process occupies an active area of 0.806 mm2 and can self-start with a minimum input voltage of 450 mV ($40~\mu $ W) and achieve maximum efficiency of 92.7 %.- 17 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (9) , 5270-5283
A 92.7% Peak Efficiency Self-Starting Boost Converter With MPPT and Phase Frequency Detector Based Multi Current Detector for Energy Harvesting Systems With a Minimum Input Source Impedance of 1 Ω
This article presents a boost converter based on a maximum power point tracking (MPPT) circuit, and a multicurrent detector (MCD), an offset cancellation circuit to achieve high efficiency over a wide range of input power. The proposed boost converter employs an MPPT design for adaptive on-time operation, which adjusts the on-time width to achieve maximum efficiency depending on the input voltage. In addition, a phase frequency detector-based offset cancellation method is proposed to minimize power loss by accurately sensing the current detector, thereby transferring power. Therefore, the proposed method achieves a significant efficiency improvement of up to 10 % by implementing high-precision offset cancellation with an offset level of approximately$5~\mu $ A, which is significantly lower than the conventional MCD offset of over 60 mA of maximum offset current level. The proposed boost converter fabricated in a 130 nm Bipolar-CMOS-DMOS (BCD) process occupies an active area of 0.806 mm2 and can self-start with a minimum input voltage of 450 mV ($40~\mu $ W) and achieve maximum efficiency of 92.7 %.- Open Access
- 9 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14226-14235
A Design of Boost Converter With Time-Domain MPPT and Digital Self-Tracking ZCD for Thermoelectric Energy Harvesting Applications
This paper presents a DC-DC boost converter for energy harvesting. The time-domain maximum power point tracking (MPPT) technique implements to maximize the source's energy harvesting performance with no additional switch and time slot. Furthermore, it is implementing digital self-tracking zero current detectors (ST-ZCD) for high efficiency. This DC-DC boost converter fabricates with a 180nm CMOS process. The input voltage of the boost converter ranges from 0.2 to 0.7V and generates the output voltage of 1.2V. The total area of this converter with the MPPT operation is 600 μm x 475 μm. The measured power conversion efficiency of this DC-DC boost converter is 85.5%.
- 9 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 14226-14235
Open AccessA Design of Boost Converter With Time-Domain MPPT and Digital Self-Tracking ZCD for Thermoelectric Energy Harvesting Applications
This paper presents a DC-DC boost converter for energy harvesting. The time-domain maximum power point tracking (MPPT) technique implements to maximize the source's energy harvesting performance with no additional switch and time slot. Furthermore, it is implementing digital self-tracking zero current detectors (ST-ZCD) for high efficiency. This DC-DC boost converter fabricates with a 180nm CMOS process. The input voltage of the boost converter ranges from 0.2 to 0.7V and generates the output voltage of 1.2V. The total area of this converter with the MPPT operation is 600 μm x 475 μm. The measured power conversion efficiency of this DC-DC boost converter is 85.5%.
- Open Access
- 1 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (7) , 1118
Low Phase-Noise, 2.4 and 5.8 GHz Dual-Band Frequency Synthesizer with Class-C VCO and Bias-Controlled Charge Pump for RF Wireless Charging System in 180 nm CMOS Process
This paper presents an integer-N phase-locked loop (PLL) for an RF wireless charging system. To improve the phase-noise characteristics under low power, a constant amplitude control class-C voltage-controlled oscillator (VCO) with a DC-DC converter, and a bias-controlled charge pump with a feedback loop are proposed. The frequency range of the VCO is 4.5–6.1 GHz, the target frequency of the proposed PLL is 2.4 and 5.8 GHz in the industry–science–medical band. It is designed with a same phase margin and bandwidth using one loop filter. The proposed PLL consumes less than 8 mW from a 1.8 V power supply with a settling time of fewer than 20 μs and an area of 1200 μm × 800 μm in the 180 nm CMOS process. For a carrier frequency offset of 1 MHz, the measured phase noise is −118.5 dBc/Hz at 2.4 GHz and −116.6 dBc/Hz at 5.8 GHz. Its FoM including the phase noise is −197 dB at 2.4 GHz and −202.8 GHz at 5.8 GHz, outperforming other PLLs designed in the 180 nm CMOS process.
- 1 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (7) , 1118
Open AccessLow Phase-Noise, 2.4 and 5.8 GHz Dual-Band Frequency Synthesizer with Class-C VCO and Bias-Controlled Charge Pump for RF Wireless Charging System in 180 nm CMOS Process
This paper presents an integer-N phase-locked loop (PLL) for an RF wireless charging system. To improve the phase-noise characteristics under low power, a constant amplitude control class-C voltage-controlled oscillator (VCO) with a DC-DC converter, and a bias-controlled charge pump with a feedback loop are proposed. The frequency range of the VCO is 4.5–6.1 GHz, the target frequency of the proposed PLL is 2.4 and 5.8 GHz in the industry–science–medical band. It is designed with a same phase margin and bandwidth using one loop filter. The proposed PLL consumes less than 8 mW from a 1.8 V power supply with a settling time of fewer than 20 μs and an area of 1200 μm × 800 μm in the 180 nm CMOS process. For a carrier frequency offset of 1 MHz, the measured phase noise is −118.5 dBc/Hz at 2.4 GHz and −116.6 dBc/Hz at 5.8 GHz. Its FoM including the phase noise is −197 dB at 2.4 GHz and −202.8 GHz at 5.8 GHz, outperforming other PLLs designed in the 180 nm CMOS process.
- 6 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 93-94
RF-DC Converter Using Loss Compensation and Adaptive Matching Network
This paper presents a highly efficient RF-DC converter for wireless energy collection applications sensitive to very low input power with a wide dynamic range. Implemented via an adaptive matching network to fine-tune impedance matching across dynamic input ranges. To ensure operation for wide inputs, an adaptive input matching network has been applied to this proposed RF-DC converter. An adaptive matching design circuit has a relatively low conversion efficiency of DC power. To improve the efficiency and DC output of RF-DC converters, loss compensation method has been applied to design circuits. Simulation shows sensitivity of up to 55.9% PCE within 40 dBm range input when operating at 5.8 GHz.
- 6 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 93-94
RF-DC Converter Using Loss Compensation and Adaptive Matching Network
This paper presents a highly efficient RF-DC converter for wireless energy collection applications sensitive to very low input power with a wide dynamic range. Implemented via an adaptive matching network to fine-tune impedance matching across dynamic input ranges. To ensure operation for wide inputs, an adaptive input matching network has been applied to this proposed RF-DC converter. An adaptive matching design circuit has a relatively low conversion efficiency of DC power. To improve the efficiency and DC output of RF-DC converters, loss compensation method has been applied to design circuits. Simulation shows sensitivity of up to 55.9% PCE within 40 dBm range input when operating at 5.8 GHz.