Viktar Beliautsou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Viktar Beliautsou has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandra Beliautsou
Working Group on Smart Vehicle Systems / Systems and Software Engineering Group, Technische Universitt Ilmenau, Ilmenau, Germany
3 shared publications - Valentin Ivanov
Smart Vehicle Systems Group, Control Engineering Group, Technische Universität Ilmenau, Robert-Bosch-Ring 1, 98693 Ilmenau, Germany
3 shared publications Aleksandra A. Fedorova
Information Security Systems Department, University named after A. N. Tupolev-KAI, Kazan, Russia
2 shared publicationsAleksandra Fedorova
Technische Universität Ilmenau
2 shared publications- Jesus Alfonso
Grupo de Investigación Aplicada (GIA-MDPI), Instituto Tecnológico de Aragón, Zaragoza, Spain
2 shared publications - Jose Angel Castellanos
Instituto de Investigacin en Ingeniera de Aragn (I3A), Universidad de Zaragoza, Zaragoza, Spain
2 shared publications
Latest Publications
- Open Access
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 6, 1661-1672
Geographically Distributed Test Environment: Validation of Integrated Motion Control of Multi-Actuated Electric Vehicle
As an example of a geographically distributed test environment, an integrated motion control system for multi-actuated electric vehicles has been proposed and evaluated. This system unifies three active subsystems: drive-by-wire propulsion with independent in-wheel electric motors, electro-hydraulic brake actuators, and active suspension actuators. A distributed X-in-the-loop network architecture supports the approach, integrating a real-time validated vehicle model, dedicated test benches for each subsystem, and a driving simulator located in different geographical locations. This setup enables real-time testing and validation of the integrated control strategy. Validation results show improved ride comfort and safety.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 6, 1661-1672
Open AccessGeographically Distributed Test Environment: Validation of Integrated Motion Control of Multi-Actuated Electric Vehicle
As an example of a geographically distributed test environment, an integrated motion control system for multi-actuated electric vehicles has been proposed and evaluated. This system unifies three active subsystems: drive-by-wire propulsion with independent in-wheel electric motors, electro-hydraulic brake actuators, and active suspension actuators. A distributed X-in-the-loop network architecture supports the approach, integrating a real-time validated vehicle model, dedicated test benches for each subsystem, and a driving simulator located in different geographical locations. This setup enables real-time testing and validation of the integrated control strategy. Validation results show improved ride comfort and safety.
- Open Access
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Vehicular Technology Magazine
- Vol. 20 (4) , 114-122
Drone-to-Vehicle Integration of Data: Design Concept and Application to Vehicle Automation System
Modern vehicles are characterized by a high degree of environmental perception and automation. This is made possible by the development of new motion control and driver assistance systems as well as new methods for sensor-based detection of driving parameters. However, the functionality of commonly used visual and wave-based sensor systems, such as cameras, radars, etc., can be limited when installed in a vehicle as some obstacles fall into the blind zone due to the road profile or other road users. It is also difficult to detect road-specific parameters such as gradient, slope, or surface conditions with onboard vehicle sensors. A method to improve the vehicle’s detection capabilities can be proposed by extending the information channels with additional sensors by mounting them on an assistant drone. This article presents a framework for drone-to-vehicle collaboration that enables the integration of data from drone sensors into the vehicle motion control. The article gives an overview of the system, the technology created for the implementation, and the challenges to be overcome by integrating the different components. The hardware implementation of the drone and the integration of the data into the vehicle control unit (VCU) are presented. The proposed approach allows the vehicle to view the road from different angles and detect changes in road conditions from a distance. It extends the capabilities of the vehicle motion control. The effectiveness of the developed framework is experimentally validated with an electric vehicle’s velocity control and traction control on low-friction surfaces.
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Vehicular Technology Magazine
- Vol. 20 (4) , 114-122
Open AccessDrone-to-Vehicle Integration of Data: Design Concept and Application to Vehicle Automation System
Modern vehicles are characterized by a high degree of environmental perception and automation. This is made possible by the development of new motion control and driver assistance systems as well as new methods for sensor-based detection of driving parameters. However, the functionality of commonly used visual and wave-based sensor systems, such as cameras, radars, etc., can be limited when installed in a vehicle as some obstacles fall into the blind zone due to the road profile or other road users. It is also difficult to detect road-specific parameters such as gradient, slope, or surface conditions with onboard vehicle sensors. A method to improve the vehicle’s detection capabilities can be proposed by extending the information channels with additional sensors by mounting them on an assistant drone. This article presents a framework for drone-to-vehicle collaboration that enables the integration of data from drone sensors into the vehicle motion control. The article gives an overview of the system, the technology created for the implementation, and the challenges to be overcome by integrating the different components. The hardware implementation of the drone and the integration of the data into the vehicle control unit (VCU) are presented. The proposed approach allows the vehicle to view the road from different angles and detect changes in road conditions from a distance. It extends the capabilities of the vehicle motion control. The effectiveness of the developed framework is experimentally validated with an electric vehicle’s velocity control and traction control on low-friction surfaces.
- Open Access
- 9 October 2024
- Published by Elsevier in Aerospace Science and Technology
- Vol. 155
Prop-plane — New convertible VTOL UAV as a combination of a longitudinal bicopter and a flying wing with a tilt-rotor powertrain
- 9 October 2024
- Published by Elsevier in Aerospace Science and Technology
- Vol. 155
Open AccessProp-plane — New convertible VTOL UAV as a combination of a longitudinal bicopter and a flying wing with a tilt-rotor powertrain
- 6 August 2022
- Published by Springer Nature
- p. 1175-1182
Development of Torque Vectoring Controller Tuned with Neural Networks
- 6 August 2022
- Published by Springer Nature
- p. 1175-1182
Development of Torque Vectoring Controller Tuned with Neural Networks
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1002-1007
Geographically distributed real-time co-simulation of electric vehicle
The present paper shows the capabilities of a distributed real-time co-simulation environment merging simulation models and testing facilities for developing and verifying electric vehicles. This environment has been developed in the framework of the XILforEV project and the presented case is focused on a ride control with a real suspension installed on a test bench in Spain, which uses real-time information from a complete vehicle model in Germany. Given the long distance between both sites, it has been necessary to develop a specific delay compensation algorithm. This algorithm is general enough to be used in other real-time co-simulation frameworks. In the present work, the system architecture including the communication compensation is described and successfully experimentally validated.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1002-1007
Geographically distributed real-time co-simulation of electric vehicle
The present paper shows the capabilities of a distributed real-time co-simulation environment merging simulation models and testing facilities for developing and verifying electric vehicles. This environment has been developed in the framework of the XILforEV project and the presented case is focused on a ride control with a real suspension installed on a test bench in Spain, which uses real-time information from a complete vehicle model in Germany. Given the long distance between both sites, it has been necessary to develop a specific delay compensation algorithm. This algorithm is general enough to be used in other real-time co-simulation frameworks. In the present work, the system architecture including the communication compensation is described and successfully experimentally validated.
- Open Access
Colored Petri Net Modelling and Evaluation of Drone Inspection Methods for Distribution Networks
The UAV industry is developing rapidly and drones are increasingly used for monitoring industrial facilities. When designing such systems, operating companies have to find a system configuration of multiple drones that is near-optimal in terms of cost while achieving the required monitoring quality. Stochastic influences such as failures and maintenance have to be taken into account. Model-based systems engineering supplies tools and methods to solve such problems. This paper presents a method to model and evaluate such UAV systems with coloured Petri nets. It supports a modular view on typical setup elements and different types of UAVs and is based on UAV application standards. The model can be easily adapted to the most popular flight tasks and allows for estimating the monitoring frequency and determining the most appropriate grouping and configuration of UAVs, monitoring schemes, air time and maintenance periods. An important advantage is the ability to consider drone maintenance processes. Thus, the methodology will be useful in the conceptual design phase of UAVs, in monitoring planning, and in the selection of UAVs for specific monitoring tasks.
Open AccessColored Petri Net Modelling and Evaluation of Drone Inspection Methods for Distribution Networks
The UAV industry is developing rapidly and drones are increasingly used for monitoring industrial facilities. When designing such systems, operating companies have to find a system configuration of multiple drones that is near-optimal in terms of cost while achieving the required monitoring quality. Stochastic influences such as failures and maintenance have to be taken into account. Model-based systems engineering supplies tools and methods to solve such problems. This paper presents a method to model and evaluate such UAV systems with coloured Petri nets. It supports a modular view on typical setup elements and different types of UAVs and is based on UAV application standards. The model can be easily adapted to the most popular flight tasks and allows for estimating the monitoring frequency and determining the most appropriate grouping and configuration of UAVs, monitoring schemes, air time and maintenance periods. An important advantage is the ability to consider drone maintenance processes. Thus, the methodology will be useful in the conceptual design phase of UAVs, in monitoring planning, and in the selection of UAVs for specific monitoring tasks.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 11-15
Prediction Vehicle’s Speed with Using Artificial Neural Networks
We propose an approach for the vehicle’s speed prediction based on artificial neural networks. Different types of artificial neural networks were considered including MLP and RNN. A complex urban route in Kazan city was chosen for data gathering and making experiments. We demonstrated that it is possible to obtain sufficient accuracy for speed prediction based on limited source data. We got the prediction accuracy as 99.6% for the first future second and 94% for the tenth future second. Simple RNN showed better results for given data. We can use the suggested approach for designing intellectual automatic transmission systems and other intelligent transport systems applications.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 11-15
Prediction Vehicle’s Speed with Using Artificial Neural Networks
We propose an approach for the vehicle’s speed prediction based on artificial neural networks. Different types of artificial neural networks were considered including MLP and RNN. A complex urban route in Kazan city was chosen for data gathering and making experiments. We demonstrated that it is possible to obtain sufficient accuracy for speed prediction based on limited source data. We got the prediction accuracy as 99.6% for the first future second and 94% for the tenth future second. Simple RNN showed better results for given data. We can use the suggested approach for designing intellectual automatic transmission systems and other intelligent transport systems applications.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 330-335
Determining the Composition of the Group of Drones and the Basing Method for Oil Pipeline Monitoring
We developed a mathematical model to determine the composition of the group of drones and its basing method for the oil pipeline monitoring task. The model’s specific is its possibility to calculate the cost of surveillance for a specified period. The model can work with all types of unmanned aerial vehicles. It is suitable for oil pipelines, gas pipelines, power lines, and other similar objects. This model can be used to select the drone technical characteristics for a specific application. We also implemented this model in the software application and evaluated the obtained results.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 330-335
Determining the Composition of the Group of Drones and the Basing Method for Oil Pipeline Monitoring
We developed a mathematical model to determine the composition of the group of drones and its basing method for the oil pipeline monitoring task. The model’s specific is its possibility to calculate the cost of surveillance for a specified period. The model can work with all types of unmanned aerial vehicles. It is suitable for oil pipelines, gas pipelines, power lines, and other similar objects. This model can be used to select the drone technical characteristics for a specific application. We also implemented this model in the software application and evaluated the obtained results.
- 26 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Development of a Stabilizing System for Quadcopter with Variable Thrust Vectors
The unmanned aerial vehicle created on the base of a quadcopter with the ability to control the thrust vector for each motor will have an advantage compared to the same vehicle without this option. This advantage reaches due to the possibility to create moving forces and reactions on the external excitations, without a pitch and roll angles of the whole body. With the help of a controlled thrust vector, unmanned aerial vehicles can move in space with a completely horizontal position. The horizontal position of a body allows minimizing aerodynamic impact during maneuvering. However, to control this system, it is necessary to take into account a lot of parameters and dependencies, so there are many ways to drive such a vehicle. In this article, we describe our approach to control the thrust vector for each motor.
- 26 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Development of a Stabilizing System for Quadcopter with Variable Thrust Vectors
The unmanned aerial vehicle created on the base of a quadcopter with the ability to control the thrust vector for each motor will have an advantage compared to the same vehicle without this option. This advantage reaches due to the possibility to create moving forces and reactions on the external excitations, without a pitch and roll angles of the whole body. With the help of a controlled thrust vector, unmanned aerial vehicles can move in space with a completely horizontal position. The horizontal position of a body allows minimizing aerodynamic impact during maneuvering. However, to control this system, it is necessary to take into account a lot of parameters and dependencies, so there are many ways to drive such a vehicle. In this article, we describe our approach to control the thrust vector for each motor.