Khushbu Singh Raghav
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Khushbu Singh Raghav has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Deepak Bansal
CSIR-Central Electronics Engineering Research Institute
5 shared publications - Amit Kumar
CSIR-Central Electronics Engineering Research Institute
3 shared publications - Deepak Panwar
CSIR-Central Electronics Engineering Research Institute
2 shared publications - Mahesh Angira
NIT Hamirpur
2 shared publications - Amit Kumar
CSIR—Central Electronics Engineering Research Institute
1 shared publication - Bhawani Shankar Jangir
CSIR—Central Electronics Engineering Research Institute
1 shared publication
Latest Publications
- 1 August 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (8) , 085013
Enhancing RF MEMS SPDT switch performance through fabrication and ground balance
Radio frequency microelectromechanical system switches are gaining attention as an alternative to solid-state switches due to their low loss, high isolation, and excellent linearity. Although many single-pole single-throw designs are reported in the literature, multiport switches, especially single-pole double-throw (SPDT) switches, remain limited despite their key role in phase shifters, antenna switching, and transceiver systems. In Coplanar Waveguide-based SPDT switches, residual stress in the beam and grounding effects strongly influence pull-in voltage, beam deformation, insertion loss, and isolation. This work presents the complete development of an SPDT switch from design to measurement. Short- and long-path layouts are evaluated, with the short path showing better return loss. A solid cantilever initially requires a high pull-in voltage, which is reduced by introducing two windows near the anchor and tip, resulting in better damping and more stable contact. The fabrication process is also optimised to mitigate stress in the switch. After fabrication, a high insertion loss is observed due to the absence of a common ground. To overcome this, double wire-bond ground bridges are implemented to equalise the grounds, significantly improving insertion loss and yielding smooth isolation across the 100 MHz–20 GHz range.
- 1 August 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (8) , 085013
Enhancing RF MEMS SPDT switch performance through fabrication and ground balance
Radio frequency microelectromechanical system switches are gaining attention as an alternative to solid-state switches due to their low loss, high isolation, and excellent linearity. Although many single-pole single-throw designs are reported in the literature, multiport switches, especially single-pole double-throw (SPDT) switches, remain limited despite their key role in phase shifters, antenna switching, and transceiver systems. In Coplanar Waveguide-based SPDT switches, residual stress in the beam and grounding effects strongly influence pull-in voltage, beam deformation, insertion loss, and isolation. This work presents the complete development of an SPDT switch from design to measurement. Short- and long-path layouts are evaluated, with the short path showing better return loss. A solid cantilever initially requires a high pull-in voltage, which is reduced by introducing two windows near the anchor and tip, resulting in better damping and more stable contact. The fabrication process is also optimised to mitigate stress in the switch. After fabrication, a high insertion loss is observed due to the absence of a common ground. To overcome this, double wire-bond ground bridges are implemented to equalise the grounds, significantly improving insertion loss and yielding smooth isolation across the 100 MHz–20 GHz range.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 11770-11777
Fabrication, Characterization, and Optimization of Robust Sensing Materials for MEMS LC Resonators in Harsh Aqueous Environments
Sensing in harsh aqueous environments remains a critical challenge due to the limited lifetime and reliability of conventional electrode-based sensors. While laboratory-based techniques such as mass spectrometry, infrared spectroscopy, Raman spectroscopy, chromatography, filtration, multiple fermentation tube techniques, DNA amplification, capillary electrophoresis, field-flow fractionation, and fluorescence in situ hybridization (FISH) technique offer high accuracy for heavy metal ion detection, their complexity, cost, and lack of portability restrict their use for on-site monitoring. Resonant sensing, such as MEMS-based LC resonators, offers a promising alternative; however, their long-term performance is often constrained by chemical degradation of electrode materials when exposed to harsh aqueous media. Thus, in the presented work, a hard and chemically inert multilayer electrode stack (Ti/TiN/Al/Ti/TiN) is developed, with material selection optimized using the TOPSIS approach, and deposition is optimized within a single sputtering system. Titanium nitride is employed as the top protective layer due to its excellent chemical and mechanical stability under both acidic and alkaline conditions. The robustness of the proposed materials stack is experimentally validated across a wide pH range representative of industrial runoff, river water, and seawater, demonstrating negligible degradation in resonator performance. As a case study, lead nitrate is introduced to illustrate the sensor response, where changes in the dielectric and conductive properties of the aqueous medium result in measurable shifts in the resonator’s S21 parameter. Both simulated and measured results show good agreement, confirming the viability of the proposed platform. The presented materials stack and resonator architecture provide a robust sensing platform, which can be readily extended to resonant sensing of various analytes in harsh aqueous environments.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 11770-11777
Fabrication, Characterization, and Optimization of Robust Sensing Materials for MEMS LC Resonators in Harsh Aqueous Environments
Sensing in harsh aqueous environments remains a critical challenge due to the limited lifetime and reliability of conventional electrode-based sensors. While laboratory-based techniques such as mass spectrometry, infrared spectroscopy, Raman spectroscopy, chromatography, filtration, multiple fermentation tube techniques, DNA amplification, capillary electrophoresis, field-flow fractionation, and fluorescence in situ hybridization (FISH) technique offer high accuracy for heavy metal ion detection, their complexity, cost, and lack of portability restrict their use for on-site monitoring. Resonant sensing, such as MEMS-based LC resonators, offers a promising alternative; however, their long-term performance is often constrained by chemical degradation of electrode materials when exposed to harsh aqueous media. Thus, in the presented work, a hard and chemically inert multilayer electrode stack (Ti/TiN/Al/Ti/TiN) is developed, with material selection optimized using the TOPSIS approach, and deposition is optimized within a single sputtering system. Titanium nitride is employed as the top protective layer due to its excellent chemical and mechanical stability under both acidic and alkaline conditions. The robustness of the proposed materials stack is experimentally validated across a wide pH range representative of industrial runoff, river water, and seawater, demonstrating negligible degradation in resonator performance. As a case study, lead nitrate is introduced to illustrate the sensor response, where changes in the dielectric and conductive properties of the aqueous medium result in measurable shifts in the resonator’s S21 parameter. Both simulated and measured results show good agreement, confirming the viability of the proposed platform. The presented materials stack and resonator architecture provide a robust sensing platform, which can be readily extended to resonant sensing of various analytes in harsh aqueous environments.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 39 (1) , 28-35
Buckling and Stress-Controlled RF MEMS Structures Using Annealing
Micro-Electro-Mechanical System (MEMS) devices show better performance as compared to solid-state devices in terms of radio frequency (RF) response, like insertion loss and isolation. However, MEMS devices face reliability issues, and stress is one of the main concerns. MEMS devices involve many non-traditional fabrication steps, like releasing hanging structures. Released MEMS structures show built-in stress from the fabrication process. This stress can cause them to bend, curl, or buckle. Especially in the case of Radio Frequency (RF) MEMS switches, curling buckling increases the pull-in voltage. In the literature, to address stress-related buckling, thermal annealing was applied at different temperatures after release. However, post-release annealing reduces the stress and results in curled-up and unstable structures. The present paper explores a novel and innovative method for thermally annealing structures at an appropriate stage to reduce stress and buckling in released cantilever structures. Annealing at the appropriate step results in a significant reduction in cantilever bending and warping, indicating effective stress relaxation and yielding straight, mechanically stable cantilevers. After controlling the stress and buckling, the pull-in voltage is reduced to 40 V, which is in close agreement with the simulated results. The measured insertion loss of the switch is -0.4 dB, and isolation is -22 dB for the DC to 20 GHz frequency range.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 39 (1) , 28-35
Buckling and Stress-Controlled RF MEMS Structures Using Annealing
Micro-Electro-Mechanical System (MEMS) devices show better performance as compared to solid-state devices in terms of radio frequency (RF) response, like insertion loss and isolation. However, MEMS devices face reliability issues, and stress is one of the main concerns. MEMS devices involve many non-traditional fabrication steps, like releasing hanging structures. Released MEMS structures show built-in stress from the fabrication process. This stress can cause them to bend, curl, or buckle. Especially in the case of Radio Frequency (RF) MEMS switches, curling buckling increases the pull-in voltage. In the literature, to address stress-related buckling, thermal annealing was applied at different temperatures after release. However, post-release annealing reduces the stress and results in curled-up and unstable structures. The present paper explores a novel and innovative method for thermally annealing structures at an appropriate stage to reduce stress and buckling in released cantilever structures. Annealing at the appropriate step results in a significant reduction in cantilever bending and warping, indicating effective stress relaxation and yielding straight, mechanically stable cantilevers. After controlling the stress and buckling, the pull-in voltage is reduced to 40 V, which is in close agreement with the simulated results. The measured insertion loss of the switch is -0.4 dB, and isolation is -22 dB for the DC to 20 GHz frequency range.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6307-6311
Design and Development of a Low Insertion Loss RF MEMS Shunt Ohmic Switch
Recent advancements in the communication arena demand small-size devices with better transmission and minimum losses. Switches are the basic building blocks for any communication system. MEMS switches offer better performance in terms of size and losses than their mechanical and solid-state counterparts. Out of different MEMS switch types, ohmic switches are preferred over capacitive switches in terms of large bandwidth. Ohmic switches work over the entire frequency range starting from dc, whereas capacitive switches only operate in a particular frequency band. Hence, ohmic switches are preferred to cover multibands. However, the insertion loss of the usual series ohmic switches is higher than the capacitive switches due to contact resistance. In this article, a new concept for a shunt ohmic switch with low insertion loss has been designed and characterized. The contact resistance term is removed from the switch in the ON state. The insertion loss of the proposed shunt ohmic switch is less than $-$ 0.3 dB, and isolation is better than $-$ 17 dB over the frequency range of dc-6 GHz. The proposed switch is suitable for all the communication bands from 2G to 6G till sub-6-GHz technology.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6307-6311
Design and Development of a Low Insertion Loss RF MEMS Shunt Ohmic Switch
Recent advancements in the communication arena demand small-size devices with better transmission and minimum losses. Switches are the basic building blocks for any communication system. MEMS switches offer better performance in terms of size and losses than their mechanical and solid-state counterparts. Out of different MEMS switch types, ohmic switches are preferred over capacitive switches in terms of large bandwidth. Ohmic switches work over the entire frequency range starting from dc, whereas capacitive switches only operate in a particular frequency band. Hence, ohmic switches are preferred to cover multibands. However, the insertion loss of the usual series ohmic switches is higher than the capacitive switches due to contact resistance. In this article, a new concept for a shunt ohmic switch with low insertion loss has been designed and characterized. The contact resistance term is removed from the switch in the ON state. The insertion loss of the proposed shunt ohmic switch is less than $-$ 0.3 dB, and isolation is better than $-$ 17 dB over the frequency range of dc-6 GHz. The proposed switch is suitable for all the communication bands from 2G to 6G till sub-6-GHz technology.
- 4 May 2022
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 36 (16) , 2260-2270
Power optimization for self-sustained IoT enabled sensor nodes
Considering the reported existing harvested power in the microwatt (µW) range, IoT-enabled sensors cannot be operated self-sustainably pertaining to their high-milliwatt (mW) range power consumption. To mitigate this, circuit optimization and the use of deep sleep code were deployed leading to power reduction from 225 mW to 264 µW. Furthermore, an increase in the harvested power by changing the antenna design, from patch to horn has been demonstrated successfully. The horn antenna was designed and fabricated at 2.45 GHz for 15 dB gain. The analytical results show that the use of the horn antenna improves the harvested RF power by 15X compared to that of the patch antenna, which is enough for self-sustained sensor operation.
- 4 May 2022
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 36 (16) , 2260-2270
Power optimization for self-sustained IoT enabled sensor nodes
Considering the reported existing harvested power in the microwatt (µW) range, IoT-enabled sensors cannot be operated self-sustainably pertaining to their high-milliwatt (mW) range power consumption. To mitigate this, circuit optimization and the use of deep sleep code were deployed leading to power reduction from 225 mW to 264 µW. Furthermore, an increase in the harvested power by changing the antenna design, from patch to horn has been demonstrated successfully. The horn antenna was designed and fabricated at 2.45 GHz for 15 dB gain. The analytical results show that the use of the horn antenna improves the harvested RF power by 15X compared to that of the patch antenna, which is enough for self-sustained sensor operation.