Yun-Min Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yun-Min Park has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Chang-Yeol Jeong
Department of Nuclear and Energy System Engineering, Dongguk University, Gyeongju-si, Republic of Korea
1 shared publication - Dong-Jin Kim
Korea Atomic Energy Research Institute (KAERI)
1 shared publication - Dongwoog Ha
Department of Nuclear and Energy System Engineering, Dongguk University, Dongdae-ro 123, Gyeongju-si 38066, Gyeongsangbuk-do, Korea
1 shared publication - Geonwoo Jeon
Department of Nuclear and Energy System Engineering, Dongguk University, Dongdae-ro 123, Gyeongju-si 38066, Gyeongsangbuk-do, Korea
1 shared publication - Hong Pyo Kim
Korea Atomic Energy Research Institute
1 shared publication - Hyoung-Min Jang
Deokyanggas Co., Ltd., 2-13 Nonggong-dangi, Bug-gu, Ulsan 44201, Korea
1 shared publication
Latest Publications
- Open Access
Early-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
Open AccessEarly-Stage M23C6 Morphology at the Phase Boundary in Type 304L Austenitic Stainless Steel Containing δ Ferrite
The early-stage M23C6 morphology at the phase boundary between austenite and δ ferrite grain in Type 304L austenitic stainless steel was investigated with transmission electron microscopy (TEM). The M23C6 has coherency with austenite grains at phase boundary. The phase boundary between the M23C6 and austenite grains has curved appearance. The curved phase boundary might be a faceted interface composed of (111) plane and the other low-index planes on the atomic scale. The M23C6 morphology at the phase boundary was identified to be a complex pyramid-like shape that has {111}, {110} and {100} interfaces. The slight deviation in the angle measured between edges of carbide in the TEM images from that calculated between edges expected from the M23C6 morphology might be attributed to multilayer growth in the interior region of the M23C6 face.
- Open Access
Three-Point Bending Properties of Hybrid Multi-Materials Using Adhesive Bonding Dependent on Strength Difference between Steel and Aluminum
The mechanical behaviors of two multi-materials, DP590 (steel sheet)–A356 (cast aluminum alloy) and SS330 (steel sheet)–A5052 (aluminum sheet), were studied. A structural adhesive was used for the joining of steel and aluminum at adhesion strengths of 10, 22, and 30 MPa. To demonstrate that the three-point bending properties depend on the difference in strength between steel and aluminum and adhesion strength, optical microscopy (OM), scanning electron microscopy (SEM), and finite-element analysis (FEA) were performed. According to the results of the bending tests on both multi-materials under the same stacking conditions, the flexural stress increased with the improvement in the adhesion strength until interface separation or aluminum fracture. At the same adhesion strength, the DP590 (lower)–A356 (upper) and SS330 (upper)–A5052 (lower) configurations exhibited a tendency to decrease in the sudden stress drop due to aluminum fracture and interface separation. The bending results were analyzed through the FEA and the stress distribution as a function of the stacking and adhesion strength was confirmed.
Open AccessThree-Point Bending Properties of Hybrid Multi-Materials Using Adhesive Bonding Dependent on Strength Difference between Steel and Aluminum
The mechanical behaviors of two multi-materials, DP590 (steel sheet)–A356 (cast aluminum alloy) and SS330 (steel sheet)–A5052 (aluminum sheet), were studied. A structural adhesive was used for the joining of steel and aluminum at adhesion strengths of 10, 22, and 30 MPa. To demonstrate that the three-point bending properties depend on the difference in strength between steel and aluminum and adhesion strength, optical microscopy (OM), scanning electron microscopy (SEM), and finite-element analysis (FEA) were performed. According to the results of the bending tests on both multi-materials under the same stacking conditions, the flexural stress increased with the improvement in the adhesion strength until interface separation or aluminum fracture. At the same adhesion strength, the DP590 (lower)–A356 (upper) and SS330 (upper)–A5052 (lower) configurations exhibited a tendency to decrease in the sudden stress drop due to aluminum fracture and interface separation. The bending results were analyzed through the FEA and the stress distribution as a function of the stacking and adhesion strength was confirmed.