Firat Akin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Firat Akin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Oktay Arikan
Yildiz Technical University
9 shared publications - Baris Kucukaydin
Kırklareli Üniversitesi
2 shared publications Allahverdi Orucov
1 shared publicationArif Hashimov
1 shared publication- Bedri Kekezoglu
Yıldız Teknik Üniversitesi Elektrik-Elektronik Fakültesi Elektrik Mühendisliği Bölümü
1 shared publication - Cihat Cagdas Uydur
Department of Electric and Energy, Technical Sciences Vocational School, Trakya University, 22030 Edirne, Türkiye
1 shared publication
Latest Publications
- 17 December 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (8) , 11243-11257
An Optimization Approach for Fault Current Limiter Installation Considering Distributed Generation Impact and Circuit Breaker Constraints
- 17 December 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (8) , 11243-11257
An Optimization Approach for Fault Current Limiter Installation Considering Distributed Generation Impact and Circuit Breaker Constraints
- Open Access
- 28 May 2025
- Published by Wiley in Journal of Applied Polymer Science
Investigation of Voltage Rise Rate Effect on the Breakdown Voltage of Solid Insulating Materials Considering Different Electrode Configurations
For reliable power equipment designs, it is critical to investigate the breakdown performances of insulating materials for a variety of scenarios, including various electrode geometries and voltage characteristics. In this study, the effect of voltage rise rate on the breakdown voltages of presspaper and styrene‐butadiene rubber/natural rubber (SBR/NR) is investigated through different electrode geometries. During the experiments, voltages were applied with rise rates of 500 and 3000 V/s, using three different electrode configurations: cylinder–cylinder, sphere–cylinder, and point–cylinder. In order to explain and support the experimental results, a simulation study was performed with COMSOL Multiphysics for electric field analysis.
- 28 May 2025
- Published by Wiley in Journal of Applied Polymer Science
Open AccessInvestigation of Voltage Rise Rate Effect on the Breakdown Voltage of Solid Insulating Materials Considering Different Electrode Configurations
For reliable power equipment designs, it is critical to investigate the breakdown performances of insulating materials for a variety of scenarios, including various electrode geometries and voltage characteristics. In this study, the effect of voltage rise rate on the breakdown voltages of presspaper and styrene‐butadiene rubber/natural rubber (SBR/NR) is investigated through different electrode geometries. During the experiments, voltages were applied with rise rates of 500 and 3000 V/s, using three different electrode configurations: cylinder–cylinder, sphere–cylinder, and point–cylinder. In order to explain and support the experimental results, a simulation study was performed with COMSOL Multiphysics for electric field analysis.
- Open Access
- 19 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11894
Exploring High Voltage Potential of 3D Printed Capacitors: A Filament-Based Comparison Through Dielectric Performance Analysis
Recent advancements in 3D printing technology have enabled the rapid production of complex structures, yet the dielectric performance of 3D printing materials and their potential for manufacturing electrical components remain insufficiently studied. In this study, a capacitor rated at 10 kV with a capacitance of 1 nF was designed and developed for high-voltage applications. During the production of the capacitor, the insulating and conductive parts were fabricated using a 3D printer. While PLA, ABS, ASA, and PETG were employed as insulating materials, aluminum was chosen as the conductive part. Theoretical calculations and the finite element method were used to validate the measured capacitance of the equipment. The performance of the prototype capacitor was analyzed through partial discharge inception voltages (PDIV), dissipation factor (tanδ), and breakdown voltage measurements. Dissipation factor measurements were performed at 2 and 4 kV voltages in the 50–400 Hz frequency range. The performance of employed materials was comparatively analyzed through experimental and simulation results. Finally, the impact of different insulating materials on the dielectric performance of the prototype capacitors was evaluated.
- 19 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (24) , 11894
Open AccessExploring High Voltage Potential of 3D Printed Capacitors: A Filament-Based Comparison Through Dielectric Performance Analysis
Recent advancements in 3D printing technology have enabled the rapid production of complex structures, yet the dielectric performance of 3D printing materials and their potential for manufacturing electrical components remain insufficiently studied. In this study, a capacitor rated at 10 kV with a capacitance of 1 nF was designed and developed for high-voltage applications. During the production of the capacitor, the insulating and conductive parts were fabricated using a 3D printer. While PLA, ABS, ASA, and PETG were employed as insulating materials, aluminum was chosen as the conductive part. Theoretical calculations and the finite element method were used to validate the measured capacitance of the equipment. The performance of the prototype capacitor was analyzed through partial discharge inception voltages (PDIV), dissipation factor (tanδ), and breakdown voltage measurements. Dissipation factor measurements were performed at 2 and 4 kV voltages in the 50–400 Hz frequency range. The performance of employed materials was comparatively analyzed through experimental and simulation results. Finally, the impact of different insulating materials on the dielectric performance of the prototype capacitors was evaluated.
- Open Access
- 29 October 2024
- Published by Bandirma Onyedi Eylul University in Mühendislik Bilimleri ve Araştırmaları Dergisi
- Vol. 6 (2) , 188-197
Optimizing Distribution Network Reconfiguration for Power Loss and Fault Current Management
This study investigates the use of network reconfiguration as a cost-effective method to optimize power system performance through the minimization of fault currents and power losses. In single-objective optimizations, the study targets the reduction of the average fault current of the buses and the power losses individually. Additionally, a multi-objective optimization study is conducted to address both parameters simultaneously. Optimization scenarios are applied on 33-bus test system through Walrus Optimizer. The results demonstrate that reconfiguration can significantly reduce power losses and fault currents, compared to the base configuration of the test system, which had a power loss of 202.60 kW and an average fault current of 2.60 p.u. Single-objective optimizations reduced power losses to 139.551 kW and minimized average fault current to 2.13 p.u. Furthermore, the multi-objective optimization provided a range of Pareto optimal solutions, examining both criteria and highlighting the flexibility of reconfiguration in adapting to power system needs.
- 29 October 2024
- Published by Bandirma Onyedi Eylul University in Mühendislik Bilimleri ve Araştırmaları Dergisi
- Vol. 6 (2) , 188-197
Open AccessOptimizing Distribution Network Reconfiguration for Power Loss and Fault Current Management
This study investigates the use of network reconfiguration as a cost-effective method to optimize power system performance through the minimization of fault currents and power losses. In single-objective optimizations, the study targets the reduction of the average fault current of the buses and the power losses individually. Additionally, a multi-objective optimization study is conducted to address both parameters simultaneously. Optimization scenarios are applied on 33-bus test system through Walrus Optimizer. The results demonstrate that reconfiguration can significantly reduce power losses and fault currents, compared to the base configuration of the test system, which had a power loss of 202.60 kW and an average fault current of 2.60 p.u. Single-objective optimizations reduced power losses to 139.551 kW and minimized average fault current to 2.13 p.u. Furthermore, the multi-objective optimization provided a range of Pareto optimal solutions, examining both criteria and highlighting the flexibility of reconfiguration in adapting to power system needs.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
FEM Based Air-Core Reactor Modelling for Series Inductor of SPRFCL
The increment of fault currents is a serious problem for power systems. Fault current limiters (FCL) are proposed as a solution to alleviate the effects of high fault currents to system components. Solid-state fault current limiters (SSFCL) are effective to limit fault currents as a controlled and fast-response devices. Topological approaches are generally made for SSFCLs, however, there are not enough studies on design and performance analysis of equipment for high voltage applications. In this study, the physical design of an air-core reactor that will be an inductor of series-parallel resonance-type fault current limiter (SPRFCL) is handled for a test system of 20 kV. The air-core reactor model is constituted via COMSOL Multiphysics which involves an electrical circuit coupled with a Finite Element Method (FEM) based design. After expected inductance value of reactor achieved, the electrical simulations are made. The results of fault current and magnetic flux density values of air-core reactor are obtained from COMSOL Multiphysics. In order to validate the operation of the air-core reactor, the same power system was modeled in PSCAD and the results were found to be compatible for the same fault scenarios.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
FEM Based Air-Core Reactor Modelling for Series Inductor of SPRFCL
The increment of fault currents is a serious problem for power systems. Fault current limiters (FCL) are proposed as a solution to alleviate the effects of high fault currents to system components. Solid-state fault current limiters (SSFCL) are effective to limit fault currents as a controlled and fast-response devices. Topological approaches are generally made for SSFCLs, however, there are not enough studies on design and performance analysis of equipment for high voltage applications. In this study, the physical design of an air-core reactor that will be an inductor of series-parallel resonance-type fault current limiter (SPRFCL) is handled for a test system of 20 kV. The air-core reactor model is constituted via COMSOL Multiphysics which involves an electrical circuit coupled with a Finite Element Method (FEM) based design. After expected inductance value of reactor achieved, the electrical simulations are made. The results of fault current and magnetic flux density values of air-core reactor are obtained from COMSOL Multiphysics. In order to validate the operation of the air-core reactor, the same power system was modeled in PSCAD and the results were found to be compatible for the same fault scenarios.