Denghui Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Denghui Li has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Cong Chen
School of Chemistry and Materials Science Qinghai Minzu University Xining China
8 shared publications - Changfei Sun
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
6 shared publications - Zhenjie Zhai
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
6 shared publications - Zhe Wang
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
4 shared publications - Haitao Dong
College of Physics and Electronic Information Engineering, Qinghai Minzu University, Xining 810007, China
2 shared publications - Qian Lei
State Key Laboratory for Powder Metallurgy Central South University Changsha China
2 shared publications
Latest Publications
- Open Access
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Correction: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Open AccessCorrection: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- Open Access
The Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
Open AccessThe Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
- Open Access
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Open AccessStudy on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- 5 January 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 287, 109919
Analytical thermal modeling for conventional and in-situ laser assisted turning
- 5 January 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 287, 109919
Analytical thermal modeling for conventional and in-situ laser assisted turning
- Open Access
- 17 April 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (4) , 120
Effect of TiC Particles on the Properties of Copper Matrix Composites
In this study, TiC particle-reinforced Cu-based composites were prepared by powder metallurgy and spark plasma sintering (SPS) techniques. The mechanical and electrical properties of TiC/Cu composites were analyzed in conjunction with micro-morphology. The results showed that: TiC was fully diffused in the Cu matrix at a sintering temperature of 900 °C. The micron-sized TiC particles were most uniformly distributed in the Cu matrix and had the best performance. At this time, the densification of 5 wt.% TiC/Cu composites reached 97.19%, and the conductivity, hardness, and compressive yield strength were 11.47 MS·m−1, 112.9 HV, and 162 MPa, respectively. The effect of TiC content on the overall properties of the composites was investigated at a sintering temperature of 900 °C. The TiC content of the composites was also found to have a significant influence on the overall properties of the composites. The best performance of the composites was obtained when the TiC mass fraction was 10%. The average values of density, hardness, yield strength and conductivity of the 10 wt.% TiC/Cu composites were 90.07%, 128.3 HV, 272 MPa and 9.98 MS·m−1, respectively. The yield strength was 272 MPa, and the compressive strain was 38.8%. With the increase in TiC content, although the yield strength increased, the brittleness increased due to more weak interfaces in the composites.
- 17 April 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (4) , 120
Open AccessEffect of TiC Particles on the Properties of Copper Matrix Composites
In this study, TiC particle-reinforced Cu-based composites were prepared by powder metallurgy and spark plasma sintering (SPS) techniques. The mechanical and electrical properties of TiC/Cu composites were analyzed in conjunction with micro-morphology. The results showed that: TiC was fully diffused in the Cu matrix at a sintering temperature of 900 °C. The micron-sized TiC particles were most uniformly distributed in the Cu matrix and had the best performance. At this time, the densification of 5 wt.% TiC/Cu composites reached 97.19%, and the conductivity, hardness, and compressive yield strength were 11.47 MS·m−1, 112.9 HV, and 162 MPa, respectively. The effect of TiC content on the overall properties of the composites was investigated at a sintering temperature of 900 °C. The TiC content of the composites was also found to have a significant influence on the overall properties of the composites. The best performance of the composites was obtained when the TiC mass fraction was 10%. The average values of density, hardness, yield strength and conductivity of the 10 wt.% TiC/Cu composites were 90.07%, 128.3 HV, 272 MPa and 9.98 MS·m−1, respectively. The yield strength was 272 MPa, and the compressive strain was 38.8%. With the increase in TiC content, although the yield strength increased, the brittleness increased due to more weak interfaces in the composites.
- Open Access
- 24 February 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (5) , 418
Mechanical Properties of Ti3AlC2/Cu Composites Reinforced by MAX Phase Chemical Copper Plating
Among the various reinforcement phases available in Cu-based composites, the unique layered structure and easy diffusion of A-layer atoms make MAX phases more suitable for reinforcing a copper matrix than others. In this study, Cu-coated Ti3AlC2 particles (Cu@Ti3AlC2) were prepared through electroless plating, and Cu@Ti3AlC2/Cu composites were fabricated via vacuum hot-press sintering. The phase composition and microstructure of both Cu@Ti3AlC2 powder and composites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results demonstrate the creation of successful electroless copper plating to obtain a Cu coating on Ti3AlC2 particles. At 850 °C, a small amount of Ti3AlC2 particles decompose to form TiCx, while Al atoms from the A layer of MAX phase diffuse into the Cu matrix to form a solid solution with Cu(Al). The test results reveal that the density of the Cu@Ti3AlC2/Cu composite reaches 98.5%, with a maximum compressive strength of 705 MPa, which is 8.29% higher than that of the Ti3AlC2/Cu composite. Additionally, the compressive strain reaches 37.6%, representing an increase of 12.24% compared to that exhibited by the Ti3AlC2/Cu composite.
- 24 February 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (5) , 418
Open AccessMechanical Properties of Ti3AlC2/Cu Composites Reinforced by MAX Phase Chemical Copper Plating
Among the various reinforcement phases available in Cu-based composites, the unique layered structure and easy diffusion of A-layer atoms make MAX phases more suitable for reinforcing a copper matrix than others. In this study, Cu-coated Ti3AlC2 particles (Cu@Ti3AlC2) were prepared through electroless plating, and Cu@Ti3AlC2/Cu composites were fabricated via vacuum hot-press sintering. The phase composition and microstructure of both Cu@Ti3AlC2 powder and composites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results demonstrate the creation of successful electroless copper plating to obtain a Cu coating on Ti3AlC2 particles. At 850 °C, a small amount of Ti3AlC2 particles decompose to form TiCx, while Al atoms from the A layer of MAX phase diffuse into the Cu matrix to form a solid solution with Cu(Al). The test results reveal that the density of the Cu@Ti3AlC2/Cu composite reaches 98.5%, with a maximum compressive strength of 705 MPa, which is 8.29% higher than that of the Ti3AlC2/Cu composite. Additionally, the compressive strain reaches 37.6%, representing an increase of 12.24% compared to that exhibited by the Ti3AlC2/Cu composite.
- Open Access
- 15 September 2023
- Published by MDPI AG in Preprints.org
Effect of High Temperature Synthesis of TiC and SPS Sintering on Cu-Based Composites
TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.
- 15 September 2023
- Published by MDPI AG in Preprints.org
Open AccessEffect of High Temperature Synthesis of TiC and SPS Sintering on Cu-Based Composites
TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.
- Open Access
- 1 August 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (8)
Micro-/nano-scale WC particle-reinforced Cu-based composite preparation and property study
In this paper, Cu-based composites were prepared by the powder metallurgy method with the spark plasma sintering (SPS) sintering technique using WC (tungsten carbide) particles as the reinforcing phase and Cu as the matrix. The effect of sintering temperature on the electrical and mechanical properties of the composites was investigated, and the effect of the variation in the reinforcing phase content on the electrical and mechanical properties of the composites was investigated at the optimum sintering temperature. The microstructure and properties of 5 wt. % WC/Cu composites at different sintering temperatures were investigated, and 850 °C was determined as the optimum sintering temperature. When the SPS temperature was 850 °C, the yield strength, compressive strength, compressive strain, and hardness of 10 wt. % WC/Cu composites were 321 MPa, 743 MPa, 40.42%, and 143.2 HV, respectively, which increased the yield strength and compressive strength by 697.82% and 246.84%, respectively, compared with pure Cu material.
- 1 August 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (8)
Open AccessMicro-/nano-scale WC particle-reinforced Cu-based composite preparation and property study
In this paper, Cu-based composites were prepared by the powder metallurgy method with the spark plasma sintering (SPS) sintering technique using WC (tungsten carbide) particles as the reinforcing phase and Cu as the matrix. The effect of sintering temperature on the electrical and mechanical properties of the composites was investigated, and the effect of the variation in the reinforcing phase content on the electrical and mechanical properties of the composites was investigated at the optimum sintering temperature. The microstructure and properties of 5 wt. % WC/Cu composites at different sintering temperatures were investigated, and 850 °C was determined as the optimum sintering temperature. When the SPS temperature was 850 °C, the yield strength, compressive strength, compressive strain, and hardness of 10 wt. % WC/Cu composites were 321 MPa, 743 MPa, 40.42%, and 143.2 HV, respectively, which increased the yield strength and compressive strength by 697.82% and 246.84%, respectively, compared with pure Cu material.
- Open Access
- 9 May 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (9) , 1603
A General Way to Fabricate Chain-like Ferrite with Ultralow Conductive Percolation Threshold and Wideband Absorbing Ability
The magnetic nanochain-like material has been regards as one of the most promising electromagnetic (EM) absorbing material but remains a challenging. Herein, magnetic chain-like ferrite (included Fe3O4, CoFe2O4 and NiFe2O4) are successfully produced through a general solvothermal method, using PVP as the structural-liking agent. Experimental results confirm the ultimate sample possess a 3-dimensional chain-like structure which are constructed by numerous ferrite’s nanoparticles with ~60 nm in diameter. Their electromagnetic parameters can be also manipulated by such a chain structure, especially the dielectric loss, where a sharply increases can be observed on within a lower filling ratio. It greatly benefits to the EM absorbing property. In this article, the electromagnetic absorption layer made with a lower content of ferrite possess the excellent electromagnetic absorption ability, where the optimized effective absorption band was nearly 6.4 GHz under a thickness of 1.8 mm. Moreover, the filling ratio is only 30 wt%. Our method for designing of chain-like magnetic material can be helpful for producing wideband electromagnetic absorption in a low filling ratio.
- 9 May 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (9) , 1603
Open AccessA General Way to Fabricate Chain-like Ferrite with Ultralow Conductive Percolation Threshold and Wideband Absorbing Ability
The magnetic nanochain-like material has been regards as one of the most promising electromagnetic (EM) absorbing material but remains a challenging. Herein, magnetic chain-like ferrite (included Fe3O4, CoFe2O4 and NiFe2O4) are successfully produced through a general solvothermal method, using PVP as the structural-liking agent. Experimental results confirm the ultimate sample possess a 3-dimensional chain-like structure which are constructed by numerous ferrite’s nanoparticles with ~60 nm in diameter. Their electromagnetic parameters can be also manipulated by such a chain structure, especially the dielectric loss, where a sharply increases can be observed on within a lower filling ratio. It greatly benefits to the EM absorbing property. In this article, the electromagnetic absorption layer made with a lower content of ferrite possess the excellent electromagnetic absorption ability, where the optimized effective absorption band was nearly 6.4 GHz under a thickness of 1.8 mm. Moreover, the filling ratio is only 30 wt%. Our method for designing of chain-like magnetic material can be helpful for producing wideband electromagnetic absorption in a low filling ratio.