Changfei Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Changfei Sun has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Cong Chen
School of Chemistry and Materials Science Qinghai Minzu University Xining China
10 shared publications - Denghui Li
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
6 shared publications - Zhenjie Zhai
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
5 shared publications - Zhe Wang
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
4 shared publications - Qian Lei
State Key Laboratory for Powder Metallurgy Central South University Changsha China
3 shared publications Li Denghui
School of Chemistry and Materials Science, Qinghai Minzu University, Xining, China
2 shared publications
Latest Publications
- Open Access
- 25 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (89) , e78723
Phase‐Engineered Electronic Structure of ZrO 2 Regulates the Kinetic Thermodynamic Balance of Polyiodide Chemistry in Aqueous Zn–I 2 Batteries
Aqueous Zn–I 2 batteries are fundamentally limited by the challenge of simultaneously suppressing polyiodide shuttling and maintaining rapid interfacial conversion kinetics. Herein, we demonstrate that crystal‐phase‐dependent electronic reconstruction of ZrO 2 enables regulation of this adsorption–conversion balance. A tetragonal ZrO 2 /carbon‐sphere composite (CS/t‐ZrO 2 ) is constructed through a polydopamine‐assisted confined‐growth strategy, while monoclinic ZrO 2 (m‐ZrO 2 ) serves as the phase‐controlled counterpart. Comprehensive structural, spectroscopic, and electrochemical analyses reveal that the tetragonal phase possesses a higher concentration of oxygen‐vacancy‐associated defect states and a lower work function, resulting in enhanced intrinsic interfacial charge‐transfer capability. Operando UV–vis and in situ Raman spectroscopy demonstrate that the carbon framework effectively suppresses polyiodide diffusion, whereas the tetragonal ZrO 2 interface accelerates reversible iodine conversion, together establishing a favorable adsorption‐conversion balance. Density functional theory calculations further show that the tetragonal phase moderates iodine‐intermediate adsorption and reduces the thermodynamic barriers of the I 2 /I − conversion pathway, accounting for the experimentally observed fast reaction kinetics and reduced polarization. Consequently, the CS/t‐ZrO 2 /I 2 cathode delivers a reversible capacity of 215 mAh g −1 with 97% capacity retention after 2000 cycles at an iodine loading of 4.7 mg cm −2 . This work establishes crystal‐phase engineering as a viable strategy to modulate interfacial electronic structure for conversion‐type aqueous energy‐storage systems.
- 25 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (89) , e78723
Open AccessPhase‐Engineered Electronic Structure of ZrO 2 Regulates the Kinetic Thermodynamic Balance of Polyiodide Chemistry in Aqueous Zn–I 2 Batteries
Aqueous Zn–I 2 batteries are fundamentally limited by the challenge of simultaneously suppressing polyiodide shuttling and maintaining rapid interfacial conversion kinetics. Herein, we demonstrate that crystal‐phase‐dependent electronic reconstruction of ZrO 2 enables regulation of this adsorption–conversion balance. A tetragonal ZrO 2 /carbon‐sphere composite (CS/t‐ZrO 2 ) is constructed through a polydopamine‐assisted confined‐growth strategy, while monoclinic ZrO 2 (m‐ZrO 2 ) serves as the phase‐controlled counterpart. Comprehensive structural, spectroscopic, and electrochemical analyses reveal that the tetragonal phase possesses a higher concentration of oxygen‐vacancy‐associated defect states and a lower work function, resulting in enhanced intrinsic interfacial charge‐transfer capability. Operando UV–vis and in situ Raman spectroscopy demonstrate that the carbon framework effectively suppresses polyiodide diffusion, whereas the tetragonal ZrO 2 interface accelerates reversible iodine conversion, together establishing a favorable adsorption‐conversion balance. Density functional theory calculations further show that the tetragonal phase moderates iodine‐intermediate adsorption and reduces the thermodynamic barriers of the I 2 /I − conversion pathway, accounting for the experimentally observed fast reaction kinetics and reduced polarization. Consequently, the CS/t‐ZrO 2 /I 2 cathode delivers a reversible capacity of 215 mAh g −1 with 97% capacity retention after 2000 cycles at an iodine loading of 4.7 mg cm −2 . This work establishes crystal‐phase engineering as a viable strategy to modulate interfacial electronic structure for conversion‐type aqueous energy‐storage systems.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Effect of Cu-Fe bimetallic synergy on the activity of partial oxidation of methane to methanol
This study investigates the application of β-zeolite-supported bimetallic catalysts in the methanol production from methane reaction. β-zeolite with a Si/Al ratio of 25 was synthesized via the hydrothermal method, and Cu-β, Fe-β, and Cu-Fe-β catalysts were prepared using the wet impregnation technique. Structural characterization of the catalysts was performed using SEM, EDS, XRD, FTIR, BET, NH3-TPD and XPS to characterize the catalysts. The results indicated that the metal components were successfully and uniformly loaded onto the β-zeolite surface. The synergistic effect of the Cu-Fe bimetallic loading reduced pore blockage, introduced new effective acidic sites, and optimized the pore structure to enhance mass transfer efficiency. It effectively regulates the electronic structure and valence state distribution of the metal active sites, optimizing the distribution and electronic structure of these active sites on the catalyst surface. The catalytic performance of the three catalysts was evaluated in a miniature fixed-bed reactor under varying temperatures and reaction times. Activity tests revealed that copper-active metals exhibited superior activity compared to iron-active metals during methanol production via methane partial oxidation within shorter reaction times. Performance of all catalysts improved with increasing temperature. Among the three metal-zeolite catalysts, Cu-Fe-β yielded the highest methanol yield, reaching 17.78 μmol/gcat/h at 340 °C. This study demonstrates the promising application potential of β-zeolite-supported Cu-Fe bimetallic catalysts in methane-to-methanol conversion, providing theoretical guidance for the design and development of highly efficient catalysts.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessEffect of Cu-Fe bimetallic synergy on the activity of partial oxidation of methane to methanol
This study investigates the application of β-zeolite-supported bimetallic catalysts in the methanol production from methane reaction. β-zeolite with a Si/Al ratio of 25 was synthesized via the hydrothermal method, and Cu-β, Fe-β, and Cu-Fe-β catalysts were prepared using the wet impregnation technique. Structural characterization of the catalysts was performed using SEM, EDS, XRD, FTIR, BET, NH3-TPD and XPS to characterize the catalysts. The results indicated that the metal components were successfully and uniformly loaded onto the β-zeolite surface. The synergistic effect of the Cu-Fe bimetallic loading reduced pore blockage, introduced new effective acidic sites, and optimized the pore structure to enhance mass transfer efficiency. It effectively regulates the electronic structure and valence state distribution of the metal active sites, optimizing the distribution and electronic structure of these active sites on the catalyst surface. The catalytic performance of the three catalysts was evaluated in a miniature fixed-bed reactor under varying temperatures and reaction times. Activity tests revealed that copper-active metals exhibited superior activity compared to iron-active metals during methanol production via methane partial oxidation within shorter reaction times. Performance of all catalysts improved with increasing temperature. Among the three metal-zeolite catalysts, Cu-Fe-β yielded the highest methanol yield, reaching 17.78 μmol/gcat/h at 340 °C. This study demonstrates the promising application potential of β-zeolite-supported Cu-Fe bimetallic catalysts in methane-to-methanol conversion, providing theoretical guidance for the design and development of highly efficient catalysts.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Preparation and performance study of Ag/Ag3PO4-g-C3N4/BiOI composite photocatalysts
Graphite-phase carbon nitride (gC₃N₄) is a two dimensional semiconductor material known for its tunable surface acidity/basicity, structural stability, low cost, and facile synthesis. The quaternary composite catalyst covers a broader visible light spectrum, significantly enhancing light utilization efficiency. This leads to more efficient generation of photo generated electron–hole pairs, thereby supplying abundant active species for degradation reactions.” By preparing g-C3N4/BiOI as a precursor and then fabricating the Ag/Ag3PO4-g-C3N4/BiOI quaternary photocatalyst, the photocatalytic performance was evaluated by degrading two typical water pollutants—rhodamine B (RhB) and ciprofloxacin (CIP)—under visible light. The structure and properties of the samples were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), and elemental distribution analysis, and the possible catalytic degradation mechanism was further analyzed. Among the gC₃N₄/BiOI precursors, CB3 showed the best degradation performance, achieving efficiencies of 93.3% for RhB (20 mg/L) and 83.3% for CIP (10 mg/L). Subsequently, Ag3PO4 was composited onto the CB3 precursor via the sedimentation method, and the quaternary composite was treated with photoreduction. When the photoreduction time was 20 min, the resulting 20 min Ag/Ag3PO4-CB3 showed the best catalytic activity: its degradation efficiencies for 20 mg/L RhB and 10 mg/L CIP were further enhanced to 97.0% and 90.2%, respectively. Cyclic degradation experiments further confirmed the excellent stability of the catalysts. The enhanced performance of the quaternary photocatalyst is attributed to the formation of heterojunctions (p-n junction between g-C3N4/BiOI and Z-scheme heterojunction between Ag3PO4 and g-C3N4) and the localized surface plasmon resonance (LSPR) effect of AgO. These structures efficiently promote the separation of photogenerated electron-hole pairs, extend the lifetime of photogenerated carriers, and reduce photocorrosion, thereby significantly improving the visible-light photocatalytic activity and stability.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessPreparation and performance study of Ag/Ag3PO4-g-C3N4/BiOI composite photocatalysts
Graphite-phase carbon nitride (gC₃N₄) is a two dimensional semiconductor material known for its tunable surface acidity/basicity, structural stability, low cost, and facile synthesis. The quaternary composite catalyst covers a broader visible light spectrum, significantly enhancing light utilization efficiency. This leads to more efficient generation of photo generated electron–hole pairs, thereby supplying abundant active species for degradation reactions.” By preparing g-C3N4/BiOI as a precursor and then fabricating the Ag/Ag3PO4-g-C3N4/BiOI quaternary photocatalyst, the photocatalytic performance was evaluated by degrading two typical water pollutants—rhodamine B (RhB) and ciprofloxacin (CIP)—under visible light. The structure and properties of the samples were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), and elemental distribution analysis, and the possible catalytic degradation mechanism was further analyzed. Among the gC₃N₄/BiOI precursors, CB3 showed the best degradation performance, achieving efficiencies of 93.3% for RhB (20 mg/L) and 83.3% for CIP (10 mg/L). Subsequently, Ag3PO4 was composited onto the CB3 precursor via the sedimentation method, and the quaternary composite was treated with photoreduction. When the photoreduction time was 20 min, the resulting 20 min Ag/Ag3PO4-CB3 showed the best catalytic activity: its degradation efficiencies for 20 mg/L RhB and 10 mg/L CIP were further enhanced to 97.0% and 90.2%, respectively. Cyclic degradation experiments further confirmed the excellent stability of the catalysts. The enhanced performance of the quaternary photocatalyst is attributed to the formation of heterojunctions (p-n junction between g-C3N4/BiOI and Z-scheme heterojunction between Ag3PO4 and g-C3N4) and the localized surface plasmon resonance (LSPR) effect of AgO. These structures efficiently promote the separation of photogenerated electron-hole pairs, extend the lifetime of photogenerated carriers, and reduce photocorrosion, thereby significantly improving the visible-light photocatalytic activity and stability.
- Open Access
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Correction: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Open AccessCorrection: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- Open Access
The Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
Open AccessThe Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
- 22 September 2025
- Published by Springer Nature in JOM
- Vol. 77 (11) , 8814-8824
Preparation and Properties of WC Particle-Reinforced Copper Matrix Composites Under Rare-Earth Element Modulation
- 22 September 2025
- Published by Springer Nature in JOM
- Vol. 77 (11) , 8814-8824
Preparation and Properties of WC Particle-Reinforced Copper Matrix Composites Under Rare-Earth Element Modulation
- Open Access
- 27 January 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (2) , 1-15
Enhanced degradation performance of Ag-loaded BiOI composite photocatalysts for water pollutant removal
- 27 January 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (2) , 1-15
Open AccessEnhanced degradation performance of Ag-loaded BiOI composite photocatalysts for water pollutant removal
- Open Access
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Open AccessStudy on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- Open Access
- 17 April 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (4) , 120
Effect of TiC Particles on the Properties of Copper Matrix Composites
In this study, TiC particle-reinforced Cu-based composites were prepared by powder metallurgy and spark plasma sintering (SPS) techniques. The mechanical and electrical properties of TiC/Cu composites were analyzed in conjunction with micro-morphology. The results showed that: TiC was fully diffused in the Cu matrix at a sintering temperature of 900 °C. The micron-sized TiC particles were most uniformly distributed in the Cu matrix and had the best performance. At this time, the densification of 5 wt.% TiC/Cu composites reached 97.19%, and the conductivity, hardness, and compressive yield strength were 11.47 MS·m−1, 112.9 HV, and 162 MPa, respectively. The effect of TiC content on the overall properties of the composites was investigated at a sintering temperature of 900 °C. The TiC content of the composites was also found to have a significant influence on the overall properties of the composites. The best performance of the composites was obtained when the TiC mass fraction was 10%. The average values of density, hardness, yield strength and conductivity of the 10 wt.% TiC/Cu composites were 90.07%, 128.3 HV, 272 MPa and 9.98 MS·m−1, respectively. The yield strength was 272 MPa, and the compressive strain was 38.8%. With the increase in TiC content, although the yield strength increased, the brittleness increased due to more weak interfaces in the composites.
- 17 April 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (4) , 120
Open AccessEffect of TiC Particles on the Properties of Copper Matrix Composites
In this study, TiC particle-reinforced Cu-based composites were prepared by powder metallurgy and spark plasma sintering (SPS) techniques. The mechanical and electrical properties of TiC/Cu composites were analyzed in conjunction with micro-morphology. The results showed that: TiC was fully diffused in the Cu matrix at a sintering temperature of 900 °C. The micron-sized TiC particles were most uniformly distributed in the Cu matrix and had the best performance. At this time, the densification of 5 wt.% TiC/Cu composites reached 97.19%, and the conductivity, hardness, and compressive yield strength were 11.47 MS·m−1, 112.9 HV, and 162 MPa, respectively. The effect of TiC content on the overall properties of the composites was investigated at a sintering temperature of 900 °C. The TiC content of the composites was also found to have a significant influence on the overall properties of the composites. The best performance of the composites was obtained when the TiC mass fraction was 10%. The average values of density, hardness, yield strength and conductivity of the 10 wt.% TiC/Cu composites were 90.07%, 128.3 HV, 272 MPa and 9.98 MS·m−1, respectively. The yield strength was 272 MPa, and the compressive strain was 38.8%. With the increase in TiC content, although the yield strength increased, the brittleness increased due to more weak interfaces in the composites.
- Open Access
- 24 February 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (5) , 418
Mechanical Properties of Ti3AlC2/Cu Composites Reinforced by MAX Phase Chemical Copper Plating
Among the various reinforcement phases available in Cu-based composites, the unique layered structure and easy diffusion of A-layer atoms make MAX phases more suitable for reinforcing a copper matrix than others. In this study, Cu-coated Ti3AlC2 particles (Cu@Ti3AlC2) were prepared through electroless plating, and Cu@Ti3AlC2/Cu composites were fabricated via vacuum hot-press sintering. The phase composition and microstructure of both Cu@Ti3AlC2 powder and composites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results demonstrate the creation of successful electroless copper plating to obtain a Cu coating on Ti3AlC2 particles. At 850 °C, a small amount of Ti3AlC2 particles decompose to form TiCx, while Al atoms from the A layer of MAX phase diffuse into the Cu matrix to form a solid solution with Cu(Al). The test results reveal that the density of the Cu@Ti3AlC2/Cu composite reaches 98.5%, with a maximum compressive strength of 705 MPa, which is 8.29% higher than that of the Ti3AlC2/Cu composite. Additionally, the compressive strain reaches 37.6%, representing an increase of 12.24% compared to that exhibited by the Ti3AlC2/Cu composite.
- 24 February 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (5) , 418
Open AccessMechanical Properties of Ti3AlC2/Cu Composites Reinforced by MAX Phase Chemical Copper Plating
Among the various reinforcement phases available in Cu-based composites, the unique layered structure and easy diffusion of A-layer atoms make MAX phases more suitable for reinforcing a copper matrix than others. In this study, Cu-coated Ti3AlC2 particles (Cu@Ti3AlC2) were prepared through electroless plating, and Cu@Ti3AlC2/Cu composites were fabricated via vacuum hot-press sintering. The phase composition and microstructure of both Cu@Ti3AlC2 powder and composites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results demonstrate the creation of successful electroless copper plating to obtain a Cu coating on Ti3AlC2 particles. At 850 °C, a small amount of Ti3AlC2 particles decompose to form TiCx, while Al atoms from the A layer of MAX phase diffuse into the Cu matrix to form a solid solution with Cu(Al). The test results reveal that the density of the Cu@Ti3AlC2/Cu composite reaches 98.5%, with a maximum compressive strength of 705 MPa, which is 8.29% higher than that of the Ti3AlC2/Cu composite. Additionally, the compressive strain reaches 37.6%, representing an increase of 12.24% compared to that exhibited by the Ti3AlC2/Cu composite.