Cong Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cong Chen has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Changfei Sun
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
10 shared publications - Denghui Li
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
8 shared publications - Zhenjie Zhai
School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
6 shared publications Haitao Dong
4 shared publications- Qian Lei
State Key Laboratory for Powder Metallurgy Central South University Changsha China
4 shared publications Wen Chen
4 shared publications
Latest Publications
- 25 October 2026
- Published by Wiley in Advanced Engineering Materials
Effect of Chromium Initial State on Microstructure and Properties of Graphene‐Reinforced Copper Matrix Composites
Graphene is widely used to reinforce copper composites, yet weak interfaces, inefficient stress transfer, and graphene aggregation limit practical performance. Matrix alloying serves as an effective strategy to enhance interfacial bonding; however, the impact of the initial phase state of alloying elements (prealloyed solid solution vs. mechanical mixed powder) on the microstructure and macroscopic properties of composites remains poorly understood. This study employed ball milling and hot pressing/sintering processes to prepare composites with varying graphene contents (0–1 wt.%) using either prealloyed Cu‐2%Cr powder (GA group) or mechanically mixed pure Cu/Cr powder (GM group). Results demonstrated that in the GA group, chromium was uniformly dissolved at the atomic level, enabling superior graphene dispersion with dense interfacial bonding; conversely, in the GM group, chromium existed as micron‐sized discrete particles, leading to poor graphene dispersion. The GA group exhibited significantly better mechanical and electrical properties than the GM group, showing average increases in microhardness and compressive strength by approximately 12.6% and 12.4%, respectively, alongside an 11.1% reduction in resistivity. Compressive strength peaks at 723 MPa (0.5 wt.% graphene) and drops to 207 MPa at 1.0 wt.%. Excessive graphene induces stress concentration and brittle fracture under tight interfaces, revealing strong bonding’s double‐edged sword effect.
- 25 October 2026
- Published by Wiley in Advanced Engineering Materials
Effect of Chromium Initial State on Microstructure and Properties of Graphene‐Reinforced Copper Matrix Composites
Graphene is widely used to reinforce copper composites, yet weak interfaces, inefficient stress transfer, and graphene aggregation limit practical performance. Matrix alloying serves as an effective strategy to enhance interfacial bonding; however, the impact of the initial phase state of alloying elements (prealloyed solid solution vs. mechanical mixed powder) on the microstructure and macroscopic properties of composites remains poorly understood. This study employed ball milling and hot pressing/sintering processes to prepare composites with varying graphene contents (0–1 wt.%) using either prealloyed Cu‐2%Cr powder (GA group) or mechanically mixed pure Cu/Cr powder (GM group). Results demonstrated that in the GA group, chromium was uniformly dissolved at the atomic level, enabling superior graphene dispersion with dense interfacial bonding; conversely, in the GM group, chromium existed as micron‐sized discrete particles, leading to poor graphene dispersion. The GA group exhibited significantly better mechanical and electrical properties than the GM group, showing average increases in microhardness and compressive strength by approximately 12.6% and 12.4%, respectively, alongside an 11.1% reduction in resistivity. Compressive strength peaks at 723 MPa (0.5 wt.% graphene) and drops to 207 MPa at 1.0 wt.%. Excessive graphene induces stress concentration and brittle fracture under tight interfaces, revealing strong bonding’s double‐edged sword effect.
- Open Access
- 25 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (89) , e78723
Phase‐Engineered Electronic Structure of ZrO 2 Regulates the Kinetic Thermodynamic Balance of Polyiodide Chemistry in Aqueous Zn–I 2 Batteries
Aqueous Zn–I 2 batteries are fundamentally limited by the challenge of simultaneously suppressing polyiodide shuttling and maintaining rapid interfacial conversion kinetics. Herein, we demonstrate that crystal‐phase‐dependent electronic reconstruction of ZrO 2 enables regulation of this adsorption–conversion balance. A tetragonal ZrO 2 /carbon‐sphere composite (CS/t‐ZrO 2 ) is constructed through a polydopamine‐assisted confined‐growth strategy, while monoclinic ZrO 2 (m‐ZrO 2 ) serves as the phase‐controlled counterpart. Comprehensive structural, spectroscopic, and electrochemical analyses reveal that the tetragonal phase possesses a higher concentration of oxygen‐vacancy‐associated defect states and a lower work function, resulting in enhanced intrinsic interfacial charge‐transfer capability. Operando UV–vis and in situ Raman spectroscopy demonstrate that the carbon framework effectively suppresses polyiodide diffusion, whereas the tetragonal ZrO 2 interface accelerates reversible iodine conversion, together establishing a favorable adsorption‐conversion balance. Density functional theory calculations further show that the tetragonal phase moderates iodine‐intermediate adsorption and reduces the thermodynamic barriers of the I 2 /I − conversion pathway, accounting for the experimentally observed fast reaction kinetics and reduced polarization. Consequently, the CS/t‐ZrO 2 /I 2 cathode delivers a reversible capacity of 215 mAh g −1 with 97% capacity retention after 2000 cycles at an iodine loading of 4.7 mg cm −2 . This work establishes crystal‐phase engineering as a viable strategy to modulate interfacial electronic structure for conversion‐type aqueous energy‐storage systems.
- 25 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (89) , e78723
Open AccessPhase‐Engineered Electronic Structure of ZrO 2 Regulates the Kinetic Thermodynamic Balance of Polyiodide Chemistry in Aqueous Zn–I 2 Batteries
Aqueous Zn–I 2 batteries are fundamentally limited by the challenge of simultaneously suppressing polyiodide shuttling and maintaining rapid interfacial conversion kinetics. Herein, we demonstrate that crystal‐phase‐dependent electronic reconstruction of ZrO 2 enables regulation of this adsorption–conversion balance. A tetragonal ZrO 2 /carbon‐sphere composite (CS/t‐ZrO 2 ) is constructed through a polydopamine‐assisted confined‐growth strategy, while monoclinic ZrO 2 (m‐ZrO 2 ) serves as the phase‐controlled counterpart. Comprehensive structural, spectroscopic, and electrochemical analyses reveal that the tetragonal phase possesses a higher concentration of oxygen‐vacancy‐associated defect states and a lower work function, resulting in enhanced intrinsic interfacial charge‐transfer capability. Operando UV–vis and in situ Raman spectroscopy demonstrate that the carbon framework effectively suppresses polyiodide diffusion, whereas the tetragonal ZrO 2 interface accelerates reversible iodine conversion, together establishing a favorable adsorption‐conversion balance. Density functional theory calculations further show that the tetragonal phase moderates iodine‐intermediate adsorption and reduces the thermodynamic barriers of the I 2 /I − conversion pathway, accounting for the experimentally observed fast reaction kinetics and reduced polarization. Consequently, the CS/t‐ZrO 2 /I 2 cathode delivers a reversible capacity of 215 mAh g −1 with 97% capacity retention after 2000 cycles at an iodine loading of 4.7 mg cm −2 . This work establishes crystal‐phase engineering as a viable strategy to modulate interfacial electronic structure for conversion‐type aqueous energy‐storage systems.
- 25 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (42) , 28447-28454
Dual-function electrolyte design enabling sulfur redox-mediated charging and anode stabilization in Zn-air batteries
Alkaline hydrolysis of thiourea electrolyte additive modulates cathode redox behavior and stabilizes Zn anodes, lowering the charge/discharge voltage gap of assembled Zn–air cells to 0.47 V and affording 330 h stable cycling at 10 mA cm −2 .
- 25 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (42) , 28447-28454
Dual-function electrolyte design enabling sulfur redox-mediated charging and anode stabilization in Zn-air batteries
Alkaline hydrolysis of thiourea electrolyte additive modulates cathode redox behavior and stabilizes Zn anodes, lowering the charge/discharge voltage gap of assembled Zn–air cells to 0.47 V and affording 330 h stable cycling at 10 mA cm −2 .
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Effect of Cu-Fe bimetallic synergy on the activity of partial oxidation of methane to methanol
This study investigates the application of β-zeolite-supported bimetallic catalysts in the methanol production from methane reaction. β-zeolite with a Si/Al ratio of 25 was synthesized via the hydrothermal method, and Cu-β, Fe-β, and Cu-Fe-β catalysts were prepared using the wet impregnation technique. Structural characterization of the catalysts was performed using SEM, EDS, XRD, FTIR, BET, NH3-TPD and XPS to characterize the catalysts. The results indicated that the metal components were successfully and uniformly loaded onto the β-zeolite surface. The synergistic effect of the Cu-Fe bimetallic loading reduced pore blockage, introduced new effective acidic sites, and optimized the pore structure to enhance mass transfer efficiency. It effectively regulates the electronic structure and valence state distribution of the metal active sites, optimizing the distribution and electronic structure of these active sites on the catalyst surface. The catalytic performance of the three catalysts was evaluated in a miniature fixed-bed reactor under varying temperatures and reaction times. Activity tests revealed that copper-active metals exhibited superior activity compared to iron-active metals during methanol production via methane partial oxidation within shorter reaction times. Performance of all catalysts improved with increasing temperature. Among the three metal-zeolite catalysts, Cu-Fe-β yielded the highest methanol yield, reaching 17.78 μmol/gcat/h at 340 °C. This study demonstrates the promising application potential of β-zeolite-supported Cu-Fe bimetallic catalysts in methane-to-methanol conversion, providing theoretical guidance for the design and development of highly efficient catalysts.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessEffect of Cu-Fe bimetallic synergy on the activity of partial oxidation of methane to methanol
This study investigates the application of β-zeolite-supported bimetallic catalysts in the methanol production from methane reaction. β-zeolite with a Si/Al ratio of 25 was synthesized via the hydrothermal method, and Cu-β, Fe-β, and Cu-Fe-β catalysts were prepared using the wet impregnation technique. Structural characterization of the catalysts was performed using SEM, EDS, XRD, FTIR, BET, NH3-TPD and XPS to characterize the catalysts. The results indicated that the metal components were successfully and uniformly loaded onto the β-zeolite surface. The synergistic effect of the Cu-Fe bimetallic loading reduced pore blockage, introduced new effective acidic sites, and optimized the pore structure to enhance mass transfer efficiency. It effectively regulates the electronic structure and valence state distribution of the metal active sites, optimizing the distribution and electronic structure of these active sites on the catalyst surface. The catalytic performance of the three catalysts was evaluated in a miniature fixed-bed reactor under varying temperatures and reaction times. Activity tests revealed that copper-active metals exhibited superior activity compared to iron-active metals during methanol production via methane partial oxidation within shorter reaction times. Performance of all catalysts improved with increasing temperature. Among the three metal-zeolite catalysts, Cu-Fe-β yielded the highest methanol yield, reaching 17.78 μmol/gcat/h at 340 °C. This study demonstrates the promising application potential of β-zeolite-supported Cu-Fe bimetallic catalysts in methane-to-methanol conversion, providing theoretical guidance for the design and development of highly efficient catalysts.
- Open Access
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Correction: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- 10 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1698
Open AccessCorrection: Li et al. Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements. Nanomaterials 2025, 15, 96
Prior to the publication of the original work
- Open Access
The Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
Open AccessThe Effect of In-Situ-Grown Graphene from Highland Barley Powder on the Properties of Copper Matrix Materials
In situ graphene was grown on the surface of copper particles using highland barley powder, which is rich in sucrose and β-glucan, as a carbon source. The graphene content in the graphene-coated copper (Gr@Cu) composite powder was 4.98 wt.%. A characteristic angle of approximately 14° was observed between the graphene and copper crystal planes, indicating strong interfacial bonding. Raman spectroscopy revealed an ID/IG ratio of 0.96 for the graphene. Owing to the in situ growth of graphene, the mechanical properties of the copper matrix are effectively strengthened. At a graphene content of 0.7 wt.%, the graphene was uniformly dispersed within the copper matrix, resulting in optimized mechanical properties of the composite. This composite exhibited a conductivity of 70% IACS and a compressive yield strength of 175 MPa.
- 22 September 2025
- Published by Springer Nature in JOM
- Vol. 77 (11) , 8814-8824
Preparation and Properties of WC Particle-Reinforced Copper Matrix Composites Under Rare-Earth Element Modulation
- 22 September 2025
- Published by Springer Nature in JOM
- Vol. 77 (11) , 8814-8824
Preparation and Properties of WC Particle-Reinforced Copper Matrix Composites Under Rare-Earth Element Modulation
- Open Access
- 27 January 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (2) , 1-15
Enhanced degradation performance of Ag-loaded BiOI composite photocatalysts for water pollutant removal
- 27 January 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (2) , 1-15
Open AccessEnhanced degradation performance of Ag-loaded BiOI composite photocatalysts for water pollutant removal
- Open Access
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Study on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- 9 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (2) , 96
Open AccessStudy on the Electrical and Mechanical Properties of TiC Particle-Reinforced Copper Matrix Composites Regulated by Different Rare Earth Elements
Copper matrix composites (CMCs) synergistically reinforced with rare earth oxides (Re2O3) and TiC were prepared using a powder metallurgy process with vacuum hot-pressing and sintering technology, aiming to explore new ways to optimize the properties of composites. Through this innovative approach, we propose a new solution strategy and idea for the difficult problem of mutual constraints between electrical and mechanical properties faced by traditional dual-phase reinforced Cu-matrix composites. Meanwhile, the modulation mechanism of Re2O3 in CMCs and the electrical and mechanical properties of the composites were investigated. The compressive yield strength was improved from pure Cu (50 MPa) to TiC/Cu (159 MPa). The yield strength of Eu2O3-TiC/Cu obtained after biphasic strengthening is 213 MPa, which is 326% higher than that of pure Cu, and the ultimate compressive strength reaches 790 MPa. The conductivity was enhanced from TiC/Cu (81.4% IACS) to La2O3-TiC/Cu (87.3% IACS).
- 27 August 2024
- Published by Springer Nature in JOM
- Vol. 76 (11) , 6751-6763
Effects of Different Rare Earth Oxides on the Physical, Friction and Wear Properties of ZrC-Cu Composites
- 27 August 2024
- Published by Springer Nature in JOM
- Vol. 76 (11) , 6751-6763
Effects of Different Rare Earth Oxides on the Physical, Friction and Wear Properties of ZrC-Cu Composites