Victor Vega-Gonzalez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Victor Vega-Gonzalez has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chen Wu
Imec , Kapeldreef 75, 3001 Heverlee, Belgium
1 shared publication - Christophe Beral
Imec , Kapeldreef 75, 3001 Heverlee, Belgium
1 shared publication - Davide Tierno
IMEC, Leuven, Belgium
1 shared publication - Filip Schleicher
IMEC (Belgium)
1 shared publication - Frederic Lazzarino
IMEC (Belgium)
1 shared publication - Ivan Ciofi
Advanced Reliability, Robustness and Test (AR2T), imec., Leuven, Belgium
1 shared publication
Latest Publications
- 24 January 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SC) , SC1034
Resistance modeling of short-range connections: impact of current spreading
We investigated the impact of current spreading on the resistance of short-range connections by performing simulations in Synopsys Sentaurus, based on a calibrated resistivity model. As a main case study, we considered vertical-horizontal-vertical (VHV) connections, a novel cell-routing architecture based on a two-level middle-of-line scheme, that has been proposed to boost the routing of four-track standard cells beyond the 2 nm technology node. We analyzed the impact of vias and line geometry on VHV link resistance and we found that low aspect ratio (AR) lines are needed to minimize the average cell resistance. We performed extensive resistance simulations of various short-range connection schemes beyond VHV links. We concluded that large AR lines are detrimental in all cases in which the link resistance is dominated by the vias. Finally, we show that ignoring current spreading can lead to a significant miscalculation of the link resistance in such scenarios.
- 24 January 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SC) , SC1034
Resistance modeling of short-range connections: impact of current spreading
We investigated the impact of current spreading on the resistance of short-range connections by performing simulations in Synopsys Sentaurus, based on a calibrated resistivity model. As a main case study, we considered vertical-horizontal-vertical (VHV) connections, a novel cell-routing architecture based on a two-level middle-of-line scheme, that has been proposed to boost the routing of four-track standard cells beyond the 2 nm technology node. We analyzed the impact of vias and line geometry on VHV link resistance and we found that low aspect ratio (AR) lines are needed to minimize the average cell resistance. We performed extensive resistance simulations of various short-range connection schemes beyond VHV links. We concluded that large AR lines are detrimental in all cases in which the link resistance is dominated by the vias. Finally, we show that ignoring current spreading can lead to a significant miscalculation of the link resistance in such scenarios.
- 1 May 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 40 (3) , 032803
Extreme contact shrink for back end of line connectivity
For the past 50 years, Moore’s law has been well followed by the semiconductor industry. The scaling of transistors and interconnects has been enabled not only by various technological advancements but also by novel patterning approaches. However, in order to keep up with Moore’s law, further shrinking at all levels of the integrated circuit is needed. Among them is the back end of line (BEOL), where increasingly smaller metal pitches require tight specifications for vias connecting metal lines. In this paper, BEOL via shrink options is investigated, targeting the bottom critical dimension (CD) 10.5 nm in order to land on metal pitch 21 nm lines below, while maintaining low defectivity, as well as low global and local CD uniformity (CDU and LCDU, respectively). Approaches to this shrink consist of modifications to the etch chemistry at different levels of the mask etch and liner-assisted shrink, either organic or inorganic. Numerical analysis of CD-scanning electron microscopy (CDSEM) images quantitatively shows the efficiency of different approaches via shrink, together with associated CDU, LCDU, and defectivity values. CDSEM results are supplemented by large-area voltage contrast defectivity and transmission electron microscopy data sets.
- 1 May 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 40 (3) , 032803
Extreme contact shrink for back end of line connectivity
For the past 50 years, Moore’s law has been well followed by the semiconductor industry. The scaling of transistors and interconnects has been enabled not only by various technological advancements but also by novel patterning approaches. However, in order to keep up with Moore’s law, further shrinking at all levels of the integrated circuit is needed. Among them is the back end of line (BEOL), where increasingly smaller metal pitches require tight specifications for vias connecting metal lines. In this paper, BEOL via shrink options is investigated, targeting the bottom critical dimension (CD) 10.5 nm in order to land on metal pitch 21 nm lines below, while maintaining low defectivity, as well as low global and local CD uniformity (CDU and LCDU, respectively). Approaches to this shrink consist of modifications to the etch chemistry at different levels of the mask etch and liner-assisted shrink, either organic or inorganic. Numerical analysis of CD-scanning electron microscopy (CDSEM) images quantitatively shows the efficiency of different approaches via shrink, together with associated CDU, LCDU, and defectivity values. CDSEM results are supplemented by large-area voltage contrast defectivity and transmission electron microscopy data sets.