Qazi Mashaal Khan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Qazi Mashaal Khan has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Mohsen Koohestani
Ecole Suprieure dElectronique de lOuest, Angers, France
6 shared publications - Richard Perdriau
Cole Suprieure dlectronique de lOuest (ESEO), Angers, France
6 shared publications - Alastair R. Ruddle
Vehicle Resilience Technologies VRES, Horiba-MIRA,England, United Kingdom
4 shared publications - Lokesh Devaraj
Vehicle Resilience Department, HORIBA MIRA Ltd., Nuneaton, U.K.
4 shared publications - Mohamed Ramdani
Cole Suprieure dlectronique de lOuest (ESEO), Angers, France
4 shared publications - Alistair Duffy
School of Engineering and Sustainable Development, De Montfort University, Leicester, U.K.
2 shared publications
Latest Publications
- 16 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Multiscale and Multiphysics Computational Techniques
- Vol. 9, 75-83
Analysis of Q-Factor for AM-SLM Cavity Based Resonators Using Surface Roughness Models
This research delves into losses of X-band cavity resonators manufactured using additive manufacturing-selective laser melting (AM-SLM) compared to the standard subtractive manufacturing milling technology. Measured losses are benchmarked in terms of resonator (quality) $Q$ -factor. The measured data is further modelled using the Groiss and one-ball Huray models taking into account the implications of surface roughness and electrical conductivity. The unloaded $Q$ -factor is derived from frequency-dependent scattering ( $S$ ) parameters obtained from measurements and full-wave simulations. Surface roughness was found to impact the $Q$ -factor significantly and the resonant frequency marginally. Cavities based on AM-SLM technology exhibit higher roughness compared to milling and lowers the $Q$ -factor. A fusion of both manufacturing methods by milling AM-SLM cavity walls demonstrates an augmented $Q$ -factor compared to a directly printed cavity. In the study it was also found that the Groiss model tends to overestimate the $Q$ -factor owing to AM-SLM's rougher surface, while the one-ball Huray model furnishes precise projections by establishing a link between surface roughness and powder particles. Electrical conductivity's influence on $Q$ -factor was also investigated, showing negligible impact with increased surface roughness. Further, side walls of the AM-SLM cavity were more susceptible to surface roughness, compared to the cavity front walls due to higher surface current density. This study underscores the significance of analyzing surface roughness and electrical conductivity in AM-SLM cavity resonators and highlights the suitability of the one-ball Huray model for accurate $Q$ -factor prediction of microwave structures with rough surfaces.
- 16 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Multiscale and Multiphysics Computational Techniques
- Vol. 9, 75-83
Analysis of Q-Factor for AM-SLM Cavity Based Resonators Using Surface Roughness Models
This research delves into losses of X-band cavity resonators manufactured using additive manufacturing-selective laser melting (AM-SLM) compared to the standard subtractive manufacturing milling technology. Measured losses are benchmarked in terms of resonator (quality) $Q$ -factor. The measured data is further modelled using the Groiss and one-ball Huray models taking into account the implications of surface roughness and electrical conductivity. The unloaded $Q$ -factor is derived from frequency-dependent scattering ( $S$ ) parameters obtained from measurements and full-wave simulations. Surface roughness was found to impact the $Q$ -factor significantly and the resonant frequency marginally. Cavities based on AM-SLM technology exhibit higher roughness compared to milling and lowers the $Q$ -factor. A fusion of both manufacturing methods by milling AM-SLM cavity walls demonstrates an augmented $Q$ -factor compared to a directly printed cavity. In the study it was also found that the Groiss model tends to overestimate the $Q$ -factor owing to AM-SLM's rougher surface, while the one-ball Huray model furnishes precise projections by establishing a link between surface roughness and powder particles. Electrical conductivity's influence on $Q$ -factor was also investigated, showing negligible impact with increased surface roughness. Further, side walls of the AM-SLM cavity were more susceptible to surface roughness, compared to the cavity front walls due to higher surface current density. This study underscores the significance of analyzing surface roughness and electrical conductivity in AM-SLM cavity resonators and highlights the suitability of the one-ball Huray model for accurate $Q$ -factor prediction of microwave structures with rough surfaces.
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (3) , 780-793
Validation of IC Conducted Emission and Immunity Models Including Aging and Thermal Stress
Environmental factors, such as aging and thermal stress, can seriously impact the electromagnetic compatibility behavior of an integrated circuit (IC). The standardized IC emission model for conducted emission (ICEM-CE) and IC immunity model for conducted immunity (ICIM-CI) can be used in industry to predict electromagnetic behavior at the IC and the printed circuit board level. However, these do not take into account the effect of aging and extreme temperature variations. In this article, a custom IC designed in silicon-on-insulator technology, containing several independent analog blocks, is used to characterize the influence of aging and temperature on conducted emission and immunity through measurements and transistor-level simulations. The highly accelerated temperature and humidity stress test (HAST) was performed to evaluate aging and its influence on IC parameters. The results show that the passive distribution network is only influenced by thermal stress and not HAST aging. The latter mainly affects the active elements in the IC and reduces the conducted emission and immunity levels through intrinsic permanent degradation mechanisms. Furthermore, thermal stress mainly causes drifts in the transistor characteristics (such as threshold voltage and effective mobility), which affect the conducted emission and immunity levels and resulting in soft failures. All drifts/tolerances collected from measurements and simulations are characterized in a way that makes it possible to include them in potential future versions of the ICEM-CE and ICIM-CI standards.
- 16 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (3) , 780-793
Validation of IC Conducted Emission and Immunity Models Including Aging and Thermal Stress
Environmental factors, such as aging and thermal stress, can seriously impact the electromagnetic compatibility behavior of an integrated circuit (IC). The standardized IC emission model for conducted emission (ICEM-CE) and IC immunity model for conducted immunity (ICIM-CI) can be used in industry to predict electromagnetic behavior at the IC and the printed circuit board level. However, these do not take into account the effect of aging and extreme temperature variations. In this article, a custom IC designed in silicon-on-insulator technology, containing several independent analog blocks, is used to characterize the influence of aging and temperature on conducted emission and immunity through measurements and transistor-level simulations. The highly accelerated temperature and humidity stress test (HAST) was performed to evaluate aging and its influence on IC parameters. The results show that the passive distribution network is only influenced by thermal stress and not HAST aging. The latter mainly affects the active elements in the IC and reduces the conducted emission and immunity levels through intrinsic permanent degradation mechanisms. Furthermore, thermal stress mainly causes drifts in the transistor characteristics (such as threshold voltage and effective mobility), which affect the conducted emission and immunity levels and resulting in soft failures. All drifts/tolerances collected from measurements and simulations are characterized in a way that makes it possible to include them in potential future versions of the ICEM-CE and ICIM-CI standards.
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 138-148
Influence of Temperature on the EFT Immunity of Multistage Integrated Oscillators
The reliable operation of an integrated circuit (IC) can be affected by transient electromagnetic disturbances and temperature variations. In this paper, the performance of three oscillator circuits, namely 3- and 5-stage current-starved voltage controlled oscillators and a 3-stage ring oscillator, is compared with respect to electrical fast transients (EFT) under the influence of thermal stress. The main objective is to compare and assess, by means of measurements, the EFT immunities of integrated oscillators with the same electrostatic discharge (ESD) protections but different circuit topologies. The failure modes caused by EFT are proposed based on the considered failure criterion. Moreover, the importance of the IC package on the immunity levels of each oscillator is investigated. The output frequency response of each oscillator to the combined EFT and temperature stresses is analyzed without the external parasitics. The results show that the 5-stage CSVCO is most resilient towards temperature variations, whereas it is the least immune to the combined effect of EFT and temperature. Moreover, a distinct behavior in each tested oscillator’s frequency is observed for the in-phase EFT injections due to the topology of the circuit. Relevant MOSFET characteristics such as on-state drain-to-source resistance, power dissipation, effective mobility and threshold voltage are further analyzed under the influence of thermal stress and EFT. The root cause of higher EFT susceptibility of the 5-stage CSVCO is found to be the considerable variation of the on-state resistance due to the combined reduction of effective mobility and absolute threshold voltage levels of the MOSFETs.
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 138-148
Influence of Temperature on the EFT Immunity of Multistage Integrated Oscillators
The reliable operation of an integrated circuit (IC) can be affected by transient electromagnetic disturbances and temperature variations. In this paper, the performance of three oscillator circuits, namely 3- and 5-stage current-starved voltage controlled oscillators and a 3-stage ring oscillator, is compared with respect to electrical fast transients (EFT) under the influence of thermal stress. The main objective is to compare and assess, by means of measurements, the EFT immunities of integrated oscillators with the same electrostatic discharge (ESD) protections but different circuit topologies. The failure modes caused by EFT are proposed based on the considered failure criterion. Moreover, the importance of the IC package on the immunity levels of each oscillator is investigated. The output frequency response of each oscillator to the combined EFT and temperature stresses is analyzed without the external parasitics. The results show that the 5-stage CSVCO is most resilient towards temperature variations, whereas it is the least immune to the combined effect of EFT and temperature. Moreover, a distinct behavior in each tested oscillator’s frequency is observed for the in-phase EFT injections due to the topology of the circuit. Relevant MOSFET characteristics such as on-state drain-to-source resistance, power dissipation, effective mobility and threshold voltage are further analyzed under the influence of thermal stress and EFT. The root cause of higher EFT susceptibility of the 5-stage CSVCO is found to be the considerable variation of the on-state resistance due to the combined reduction of effective mobility and absolute threshold voltage levels of the MOSFETs.
- 12 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (6) , 2067-2079
Application of Probabilistic Models for Multitone Electromagnetic Immunity Analysis
The operational environment of modern electronic systems may include multiple frequency electromagnetic disturbances. However, immunity measurements usually employ single-frequency continuous waveforms (i.e., single-tones ). The performances of two oscillator circuits with different topologies (one simulated and one measured) were used as case studies to investigate immunity to simultaneous single-tone disturbances (i.e., multitones ) using probabilistic Bayesian network models. For the multitone analysis, the noisy-OR model was first used to identify the type of causal interactions between simultaneously occurring single-tones. Probabilistic theories derived from the recursive noisy-OR model, which inherits the independence assumptions of the noisy-OR and any known causal dependence between simultaneously occurring single-tones, were then used to predict the probability of higher order multitone failures. For the two case studies, the probability of three-tone failures was estimated using the single-tone and two-tone failure probability values. An improved adaptive recursive noisy-OR model was also proposed to overcome the practical difficulties of obtaining multitone failure probabilities, from either simulations or measurements.
- 12 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 64 (6) , 2067-2079
Application of Probabilistic Models for Multitone Electromagnetic Immunity Analysis
The operational environment of modern electronic systems may include multiple frequency electromagnetic disturbances. However, immunity measurements usually employ single-frequency continuous waveforms (i.e., single-tones ). The performances of two oscillator circuits with different topologies (one simulated and one measured) were used as case studies to investigate immunity to simultaneous single-tone disturbances (i.e., multitones ) using probabilistic Bayesian network models. For the multitone analysis, the noisy-OR model was first used to identify the type of causal interactions between simultaneously occurring single-tones. Probabilistic theories derived from the recursive noisy-OR model, which inherits the independence assumptions of the noisy-OR and any known causal dependence between simultaneously occurring single-tones, were then used to predict the probability of higher order multitone failures. For the two case studies, the probability of three-tone failures was estimated using the single-tone and two-tone failure probability values. An improved adaptive recursive noisy-OR model was also proposed to overcome the practical difficulties of obtaining multitone failure probabilities, from either simulations or measurements.
- Open Access
- 8 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 83898-83915
Experimental Characterization of Multitone EM Immunity of Integrated Oscillators Under Thermal Stress
The reliable operation of an integrated circuit can be affected by environmental changes, such as of multiple frequency electromagnetic (EM) disturbances and temperature variations. This paper compares the performance of two oscillator circuits, namely a current-starved voltage controlled oscillator and a ring oscillator integrated into a chip, in terms of their immunity to multitone direct power injection while under the influence of thermal stress. The objective is to demonstrate by the means of measurements the synergistic effect caused by multitone EM disturbances in a test chip, in contrast to the conventional single-tone EM disturbances. Moreover, the multitone immunity levels of integrated blocks with different architectures but similar functionality are analyzed at extreme temperature deviations. Bayesian networks (BN) are applied in order to visualize the probability of circuit failure due to multitone disturbances and temperature influence. Additionally, noisy-OR and improved-adaptive-recursive-noisy-OR (I-ARNOR) probabilistic models are implemented to identify the types of causal interactions (i.e. inhibition and positive causality) between multitone disturbances and to predict the probability of failure due to higher order multitone disturbances, respectively.
- 8 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 83898-83915
Open AccessExperimental Characterization of Multitone EM Immunity of Integrated Oscillators Under Thermal Stress
The reliable operation of an integrated circuit can be affected by environmental changes, such as of multiple frequency electromagnetic (EM) disturbances and temperature variations. This paper compares the performance of two oscillator circuits, namely a current-starved voltage controlled oscillator and a ring oscillator integrated into a chip, in terms of their immunity to multitone direct power injection while under the influence of thermal stress. The objective is to demonstrate by the means of measurements the synergistic effect caused by multitone EM disturbances in a test chip, in contrast to the conventional single-tone EM disturbances. Moreover, the multitone immunity levels of integrated blocks with different architectures but similar functionality are analyzed at extreme temperature deviations. Bayesian networks (BN) are applied in order to visualize the probability of circuit failure due to multitone disturbances and temperature influence. Additionally, noisy-OR and improved-adaptive-recursive-noisy-OR (I-ARNOR) probabilistic models are implemented to identify the types of causal interactions (i.e. inhibition and positive causality) between multitone disturbances and to predict the probability of failure due to higher order multitone disturbances, respectively.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 4 (3) , 77-82
Synergistic Effect of Multitone EMI on the Conducted Immunity of Integrated Oscillators
The performance of two oscillator circuits, namely a current-starved voltage controlled oscillator and a ring oscillator, is compared with respect to multi-tone direct power injection (DPI). The objective is to investigate the impact of causal dependence between multi-tones on the immunity levels of integrated blocks with different architectures but similar functionality. The multi-tone immunity analysis performed using the probabilistic noisy-OR model reveals an increase in the probability of failure due to electromagnetic interference relatively to single-tone EM disturbance. The proportions of inhibition and positive causality, as well as the mean degree of synergy ( DoS ) caused by multi-tone EM disturbances, are extensively compared for both oscillator circuits.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 4 (3) , 77-82
Synergistic Effect of Multitone EMI on the Conducted Immunity of Integrated Oscillators
The performance of two oscillator circuits, namely a current-starved voltage controlled oscillator and a ring oscillator, is compared with respect to multi-tone direct power injection (DPI). The objective is to investigate the impact of causal dependence between multi-tones on the immunity levels of integrated blocks with different architectures but similar functionality. The multi-tone immunity analysis performed using the probabilistic noisy-OR model reveals an increase in the probability of failure due to electromagnetic interference relatively to single-tone EM disturbance. The proportions of inhibition and positive causality, as well as the mean degree of synergy ( DoS ) caused by multi-tone EM disturbances, are extensively compared for both oscillator circuits.
- 1 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 4 (2) , 25-30
A Comparative Performance Analysis of 6T & 9T SRAM Integrated Circuits: SOI vs. Bulk
This letter evaluates the performance of 6T & 9T static random access memory (SRAM) cells, for data stability and power metrics, with the aim to compare silicon-on-insulator (SOI) and bulk CMOS technologies. Each SRAM topology was designed & simulated in 180 nm 5 V XFAB-SOI and AMS-bulk processes, using optimized parameters and compatible devices. The fundamental variables analyzed were read noise margins, write trip current & voltage as well as leakage current (LC) and static power dissipation (SPD) under process and temperature (PT) variations. The static noise margin (SNM) butterfly curve and N-curve methodologies were used to assess the mentioned parameters. Compared to bulk technology, the SRAM cells designed with SOI were found to have lower SPD & LC, higher data stability, lower write ability, larger sensitivity to process variations and higher resilience to temperature deviations.
- 1 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 4 (2) , 25-30
A Comparative Performance Analysis of 6T & 9T SRAM Integrated Circuits: SOI vs. Bulk
This letter evaluates the performance of 6T & 9T static random access memory (SRAM) cells, for data stability and power metrics, with the aim to compare silicon-on-insulator (SOI) and bulk CMOS technologies. Each SRAM topology was designed & simulated in 180 nm 5 V XFAB-SOI and AMS-bulk processes, using optimized parameters and compatible devices. The fundamental variables analyzed were read noise margins, write trip current & voltage as well as leakage current (LC) and static power dissipation (SPD) under process and temperature (PT) variations. The static noise margin (SNM) butterfly curve and N-curve methodologies were used to assess the mentioned parameters. Compared to bulk technology, the SRAM cells designed with SOI were found to have lower SPD & LC, higher data stability, lower write ability, larger sensitivity to process variations and higher resilience to temperature deviations.
- Open Access
- 1 January 2021
- Published by Research Publishing Services
- p. 1867-1874
Knowledge-Based Approach for System Level Electromagnetic Safety Analysis
- 1 January 2021
- Published by Research Publishing Services
- p. 1867-1874
Open AccessKnowledge-Based Approach for System Level Electromagnetic Safety Analysis