Yao Qin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yao Qin has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Xin Ming
Shenzhen Institute for Advanced Study, UESTC, Shenzhen, China
6 shared publications - Bo Zhang
University of Electronic Science and Technology of China
5 shared publications - Zhi-Yi Lin
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
4 shared publications - Chun-Wang Zhuang
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
3 shared publications Chunwang Zhuang
2 shared publicationsLin-Min Chen
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
2 shared publications
Latest Publications
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.
- 19 May 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 138
A level shifter for high-side GaN drivers with enhanced dV/dt immunity and speed
- 19 May 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 138
A level shifter for high-side GaN drivers with enhanced dV/dt immunity and speed
- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 2215-2227
A 50-V 50-MHz High-Noise-Immunity Capacitive-Coupled Level Shifter With Digital Noise Blanker for GaN Drivers
In this paper, a high-noise-immunity capacitive-coupled level shifter with digital noise blanker (DNB) is presented for GaN drivers. During and after d $V$ /dt transitions, the DNB blanks the common mode noise induced by d $V$ /dt and converts the differential mode noise due to mismatch effect to common mode noise. This enables high d $V$ /dt immunity of 200V/ns and high mismatch tolerance not less than 15%. Moreover, a dynamic discharge control (DDC) circuit prevents coupling capacitor from charging the floating power rail within a wide negative d $V$ /dt transition range and achieves fast reset for high frequency operation. High speed, low power consumption and down to $-$ 5V negative floating power rail tolerance are also achieved. The proposed level shifter is fabricated in a 0.5- $\mu$ m BCD process and occupies an active chip area of 0.051mm $^{2}$ . Experimental results confirm that the proposed level shifter works at 50V 50MHz, achieving power consumption of 27.3pJ/transition and 1.26ns average delay with a small figure of merit (5.5(pJ $\cdot$ ns)/( $\mu $ m $^{3}\cdot$ V)). The effect of the DDC is confirmed within negative d $V$ /dt transition range of $-$ 5V/ns $\sim$ $-$ 50V/ns.
- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 2215-2227
A 50-V 50-MHz High-Noise-Immunity Capacitive-Coupled Level Shifter With Digital Noise Blanker for GaN Drivers
In this paper, a high-noise-immunity capacitive-coupled level shifter with digital noise blanker (DNB) is presented for GaN drivers. During and after d $V$ /dt transitions, the DNB blanks the common mode noise induced by d $V$ /dt and converts the differential mode noise due to mismatch effect to common mode noise. This enables high d $V$ /dt immunity of 200V/ns and high mismatch tolerance not less than 15%. Moreover, a dynamic discharge control (DDC) circuit prevents coupling capacitor from charging the floating power rail within a wide negative d $V$ /dt transition range and achieves fast reset for high frequency operation. High speed, low power consumption and down to $-$ 5V negative floating power rail tolerance are also achieved. The proposed level shifter is fabricated in a 0.5- $\mu$ m BCD process and occupies an active chip area of 0.051mm $^{2}$ . Experimental results confirm that the proposed level shifter works at 50V 50MHz, achieving power consumption of 27.3pJ/transition and 1.26ns average delay with a small figure of merit (5.5(pJ $\cdot$ ns)/( $\mu $ m $^{3}\cdot$ V)). The effect of the DDC is confirmed within negative d $V$ /dt transition range of $-$ 5V/ns $\sim$ $-$ 50V/ns.
- Top Cited Papers
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10332-10347
A Fast-Transient Capacitorless LDO With Dual Paths Active-Frequency Compensation Scheme
This article presents an area-efficient and fast-transient capless low-dropout regulator (LDO) with satisfactory static and dynamic performance in the full load current range. Active-capacitor frequency compensation strategy with push–pull charging ability is employed to reduce on-chip compensation cap without degrading loop stability at light load and improve transient response speed simultaneously. Moreover, in order to drive this compensation capacitance, it makes use of an adaptively biased signal- and transient-current boosting error amplifier as well as transient enhancement circuit with nonlinear control to achieve high loop gain/bandwidth and slew rate. The proposed LDO is implemented in a 0.35-μm 5V-CMOS process and occupies an active chip area of 0.077 mm 2 . Experimental results demonstrate that it can deliver 100-mA load current at 200-mV dropout voltage ( V IN = 2.7–3.3 V, C load ≤100 pF). It consumes 66- μ A quiescent current at light load and can recover within 0.7 μ s for load transient. The voltage spikes at the output, undergoing a maximum load current change, are controlled well below 260 mV and good line/load regulation is achieved synchronously.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10332-10347
Top Cited PapersA Fast-Transient Capacitorless LDO With Dual Paths Active-Frequency Compensation Scheme
This article presents an area-efficient and fast-transient capless low-dropout regulator (LDO) with satisfactory static and dynamic performance in the full load current range. Active-capacitor frequency compensation strategy with push–pull charging ability is employed to reduce on-chip compensation cap without degrading loop stability at light load and improve transient response speed simultaneously. Moreover, in order to drive this compensation capacitance, it makes use of an adaptively biased signal- and transient-current boosting error amplifier as well as transient enhancement circuit with nonlinear control to achieve high loop gain/bandwidth and slew rate. The proposed LDO is implemented in a 0.35-μm 5V-CMOS process and occupies an active chip area of 0.077 mm 2 . Experimental results demonstrate that it can deliver 100-mA load current at 200-mV dropout voltage ( V IN = 2.7–3.3 V, C load ≤100 pF). It consumes 66- μ A quiescent current at light load and can recover within 0.7 μ s for load transient. The voltage spikes at the output, undergoing a maximum load current change, are controlled well below 260 mV and good line/load regulation is achieved synchronously.
- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (11) , 12401-12415
A High-Efficiency and Fast-Transient Low-Dropout Regulator With Adaptive Pole Tracking Frequency Compensation Technique
An advanced smooth pole tracking technique for low dropout regulator (LDO) with a ceramic capacitor is presented in this paper. Normally, the dominant pole is at the output of LDO and becomes load dependent, which may cause loop stability issue during the whole load-current application range. The proposed frequency compensation methodology with adaptive load resistor control of error amplifier (EA) alleviates the problem and reduces the dependence of equivalent series resistance (ESR) of output capacitor. Moreover, combined with this compensation strategy, an ultra-fast EA by utilizing transconductance enhancement technique is proposed to greatly reduce output voltage spikes as well as response time of the LDO during transient. This circuit has been implemented in a 0.18μm standard CMOS process and occupies an active chip area of 0.017mm $^{2}$ . Experimental results show that it can deliver 150mA load current at 200mV dropout voltage. Good loop stability and transient responses are easily achieved without degrading other important LDO parameters.- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (11) , 12401-12415
A High-Efficiency and Fast-Transient Low-Dropout Regulator With Adaptive Pole Tracking Frequency Compensation Technique
An advanced smooth pole tracking technique for low dropout regulator (LDO) with a ceramic capacitor is presented in this paper. Normally, the dominant pole is at the output of LDO and becomes load dependent, which may cause loop stability issue during the whole load-current application range. The proposed frequency compensation methodology with adaptive load resistor control of error amplifier (EA) alleviates the problem and reduces the dependence of equivalent series resistance (ESR) of output capacitor. Moreover, combined with this compensation strategy, an ultra-fast EA by utilizing transconductance enhancement technique is proposed to greatly reduce output voltage spikes as well as response time of the LDO during transient. This circuit has been implemented in a 0.18μm standard CMOS process and occupies an active chip area of 0.017mm $^{2}$ . Experimental results show that it can deliver 150mA load current at 200mV dropout voltage. Good loop stability and transient responses are easily achieved without degrading other important LDO parameters.- 19 November 2017
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 31 (32) , 1750302
A new interface weak-capacitance detection ASIC of capacitive liquid level sensor in the rocket
- 19 November 2017
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 31 (32) , 1750302
A new interface weak-capacitance detection ASIC of capacitive liquid level sensor in the rocket