Chun-Wang Zhuang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chun-Wang Zhuang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhang
University of Electronic Science and Technology of China
3 shared publications - Xin Ming
Shenzhen Institute for Advanced Study, UESTC, Shenzhen, China
3 shared publications - Yao Qin
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
3 shared publications Lin-Min Chen
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
2 shared publications- Zhi-Yi Lin
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
2 shared publications - Mo Huang
University of Macau
1 shared publication
Latest Publications
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.