SRSandra Rodini

Sandra Rodini

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sandra Rodini has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • High-Sensitivity Displacement Detection Employing Stepped-Impedance Microstrip Line Coupled Dielectric Resonator Interrogated by a Single-Frequency Reflectometer

    by Premsai Regalla, Sandra Rodini, A. V. Praveen Kumar, Abhishek Kumar Jha, Filippo Costa

    This paper presents the design, optimization, fabrication, and experimental validation of a highly sensitive linear displacement sensor based on a cylindrical dielectric resonator (CDR) loaded on an open-ended stepped-impedance microstrip transmission line. The proposed sensor demonstrates a novel approach for achieving a sensitivity of 100 dB/mm over the 0–0.5 mm displacement range by employing a compact, fixed-frequency, reflection-mode architecture, representing the highest reported sensitivity among existing single-frequency sensors in the literature. The operational flexibility of the proposed sensor lies in its fixed-frequency (narrow-band), variable |S11| magnitude operation, which permits the use of a low-cost measurement system in place of a costly vector network analyzer (VNA). This advantage is demonstrated in this paper through validation with a low-cost reflectometer setup.

  • Wireless Detection of Pressure by using PDMS Metamaterial Absorber

    by Sandra Rodini, Arnaud Vena, Georges Chehade, Simone Genovesi, Giuliano Manara, Filippo Costa

    Pressure sensors are essential across a wide range of application domains, each requiring tailored performance characteristics. In this work, we propose a novel passive and wireless pressure sensor featuring a compact sandwich structure composed of a metasurface (MTS) layer, a compressible Polydimethylsiloxane (PDMS) substrate, and a metallic ground plane. When pressure is applied, the PDMS layer undergoes mechanical deformation, leading to both a reduction in thickness and an increase in relative permittivity, which in turn causes a measurable shift in the resonance frequency. A detailed theoretical model based on a pressure-dependent Debye formulation is presented to describe the influence of mechanical compression on the electromagnetic response. The model is validated through full-wave simulations and experimental results. The sensor operates around 22 GHz and can be interrogated wirelessly from a distance of up to 25 cm. It is capable of measuring pressures up to 55 kPa, maintaining stable performance across multiple loading cycles. Thanks to its battery-free operation, compact size, and ease of fabrication, the proposed sensor is well-suited for remote pressure monitoring in environments where conventional wired or active sensors may not be viable.


  • Microwave Capacitive Pressure Sensor Based on an Additively Manufactured Elastic Layer

    by Amirhossein Karami-Horestani, Sandra Rodini, Simone Genovesi, Ferran Paredes, Filippo Costa, Ferran Martín

    This paper presents a capacitive sensor useful for measuring pressure in the range 0 Pa − 2460 Pa. The transduction mechanism is capacitance variation caused by changes in the force exerted on the sensing element. Such sensing element is a one-port coplanar waveguide (CPW) terminated with a conductive patch wider than the CPW central strip and a step impedance resonator (SIR), etched in an independent substrate and capacitively coupled to the patch. By sandwiching an additively manufactured malleable (elastic) material between the CPW and the SIR substrate, pressure changes modify the capacitance of the SIR due to the variation of (i) the dielectric constant of such material and (ii) the separation between the SIR and CPW metal layers. The output variable is the phase of the reflection coefficient at the operating frequency, set to a value (within the microwave range) where the phase response exhibits a high phase slope (since this boosts the sensitivity). Thus, the device is a single-frequency sensor that simply necessitates a microwave oscillator, or a voltage-controlled oscillator (VCO), for signal generation in operative environment. The maximum achieved sensitivity is 65°/kPa.


  • Open Access

    Wireless mm-Wave Chipless Pressure Sensor

    by Sandra Rodini, Simone Genovesi, Giuliano Manara, Filippo Costa

    An innovative passive wireless pressure sensor is proposed. The sensor is based on a millimeter-wave chipless tag operating in the $Ka$ -band that works in combination with a dielectric superstrate. The tag consists of a frequency-selective surface (FSS) printed on an ultrathin support dielectric substrate that separates it from a ground plane. The superstrate is placed on top of the tag and encapsulated to obtain the pressure sensor. Applying pressure on the ground plane causes a shift of the resonance peak due to the change in effective permittivity. The proposed sensor can work with copolar and cross-polar interrogation and it is probed without background subtraction using only amplitude measurements. The interrogation system consists of two commercial horn antennas placed up to a distance of 64 cm from the tag and a vector network analyzer (VNA). The proposed sensor is modeled through an equivalent circuit model (ECM) to explain the working principle, it is analyzed with full-wave simulations, and finally fabricated and carefully characterized. This is, as far as we know, the first chipless pressure sensor with a reading range larger than 5 cm which is not equipped with external antennas.


  • Open Access

    Chipless Wireless Strain Sensor Based on Stretchable Piezoresistive Materials

    by Sandra Rodini, Simone Genovesi, Giuliano Manara, Filippo Costa

    Piezoresistive materials are frequently employed for the fabrication of wired strain sensors by exploiting the variation of the surface resistance observed when a mechanical stimulus is applied. However, this variation is measured by electrodes connected to the sheet. In this work we propose to extract the strain information from the piezoresistive material by using a completely wireless approach. The sensor is based on a resonant absorbing structure working at 7.39 GHz that exploits the interaction between an unstretchable metasurface and the piezoresistive material used as ground plane. When the piezoresistive sheet is stretched a variation of the reflection coefficient at the resonance frequency is observed because of the sheet resistance variation. Differently from other chipless strain sensors based on stretchable substrates which are based on a deformation of the metallic pattern under applied strain, here the strain is only applied to the piezoresistive material. The proposed passive wireless sensor has been thoroughly modelled through a transmission line approach to clarify the physical mechanism that induces the scattering modulation. Finally, experimental results that verify the proposed strain sensing approach are presented. The experiments have been carried out several times to evaluate the measurement uncertainty. A sensor sensitivity of 0.5 dB/% has been estimated. The proposed approach considerably simplifies the realization of passive wireless strain sensors as it is not required to print resonators on stretchable substrates with ad-hoc manufacturing processes, but it is sufficient to employ commercially available stretchable shielding materials.


  • A Wireless Strain Sensor based on Piezoresistive Fabrics

    by Sandra Rodini, Simone Genovesi, Giuliano Manara, Filippo Costa

    Stretchable materials are frequently studied for the realization of strain sensors. The variation of the sheet impedance when an external mechanical stimulus is applied is employed to develop strain sensors. Several strain sensors have been proposed that use these materials but most of these require a hardwired system for sensor reading. Here a simple fully wireless strain sensor is proposed. The structure comprises a periodic surface whose elementary cell provides variable absorption as a function of the stretchable material sheet impedance.

  • Electromagnetic Characterization of Thin Films by Using Non-Contacting Waveguides

    by Sandra Rodini, Simone Genovesi, Giuliano Manara, Filippo Costa

    Surface impedance represents a crucial parameter for the characterization of thin films. Indeed, materials with a sheet impedance varying as a function of their elongation could be used in radio frequency piezoresistive sensors. To estimate this quantity while having the possibility of stretching the sample under test, a waveguide-based non-contact approach is proposed. The absence of contact between the sample under test and the waveguides determines an electromagnetic field leakage, which is prevented by adopting an electromagnetic band gap (EBG) structure. The surface impedance of the sample is retrieved through an inversion procedure exploiting the scattering parameters measured using the proposed setup. The inversion procedure is based on a circuit representation of the waveguide-air-waveguide Section as a $\pi $ -junction. The reliability of the proposed measurement method has been experimentally assessed using a WR137 waveguide. The proposed method allows to accurately determine the real part of surface impedance (the sheet resistance), while higher uncertainty is achieved in the estimation of the imaginary part.


  • Surface Impedance Estimation of a Stretchable Material

    by S. Rodini, S. Genovesi, G. Manara, F. Costa

    Stretchable materials are widely used for the realization of various sensors but their radio-frequency behavior is still little explored today. Here an innovative method is proposed that allows to derive the surface impedance of such materials. This parameter is fundamental for obtaining a calibration curve of these materials for their employment as a sensitive element. The proposed method allows to obtain the surface impedance of the material while it is being stretched and is based on a contact-less measurement of the scattering parameters. By exploiting these parameters and thanks to an inversion procedure, it is possible to obtain the value of the surface impedance as the frequency and strain vary.

  • Open Access

    Contactless Waveguide Characterization of Piezoresistive Materials for Wireless Strain Sensors

    by Sandra Rodini, Simone Genovesi, Giuliano Manara, Filippo Costa

    Stretchable materials are widely used for the realization of various sensors, but their radio frequency behavior has not been fully characterized so far. Here, an innovative method is proposed for deriving the surface impedance of this kind of materials. The material characterization represents a fundamental step for exploiting the material as a sensing element within a radio frequency device. Indeed, the proposed method is capable of retrieving the surface impedance of the material while it is being stretched, thus deriving a correspondent calibration curve. The characterization approach is based on a contactless measurement of the scattering parameters using waveguides. By exploiting the measured scattering parameters, the variation in the surface impedance as a function of both frequency and strain is recovered through an analytical inversion procedure. Numerical simulations were initially performed trough a numerical electromagnetic simulator, and subsequently, experimental validation was carried out using a dedicated test bench designed to ensure a contactless measurement of the stretchable material.