BABahaa Abbas

Bahaa Abbas

*This is an algorithmically generated author record based on publicly available information.

Bahaa Abbas has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synthesis of LiCo1-XNiXO2 nanomaterial by hydrothermal method as cathode for lithium ion battery

    by Hudaa Homad, Noor Ali, Omar Al-Jubouri, Muhammad Al-Timimi, Bahaa Abbas

    The compounds of LiCoO2 (LCO) and LiCo1-xNixO2 (LCNO), with (x=0,0.25,0.5,0.75,1) were synthesized as cathode active material for lithium–ion batteries using hydrothermal technique in this study. Structure and morphology characterization were conducted for all prepared samples. The crystalline results indicate that both LCO and LCNO possess a rhombohedral structure, while the morphology results show irregular shapes. Electrochemical tests were carried out for LiCoO2 and LiCo0.25 Ni0.75O2 samples only. From the electrochemical measurements, the LiCo0.25 Ni0.75O2 demonstrate higher charge and discharge capacities compared to the LiCoO2 electrode, findings which are consistent with the electrochemical impedance spectroscopy (EIS) results. The X-ray diffraction (XRD) results of both the prepared Lithium Cobalt Oxide (LCO) and Lithium Cobalt Nickel Oxide (LCNO) samples reveal characteristic peaks at specific angles (2θ) indicating crystallographic planes. For LCO, peaks were observed at 18.96°, 37.40°, 38.35°, 39.07°, 45.29°, 49.45°, and 59.62° corresponding to crystallographic planes (003), (101), (006), (012), (104), (015), and (107) respectively. These peaks confirm the formation of a rhombohedral LiCoO2 nanostructure with space group (R-3m no.166), consistent with standard data (JCPDS 00-016-0427). The EDX spectra of the synthesized Lithium Cobalt Oxide (LCO) and Lithium Cobalt Nickel Oxide (LCNO) were analyzed. The results showed the presence of oxygen (O), cobalt (Co), and nickel (Ni) elements. However, the peak corresponding to lithium (Li) was not visible due to its low activation energy. Finally, the synthesis and characterization of LiCoO2 (LCO) and LiCo1-xNixO2 (LCNO) compounds were conducted, with electrochemical tests indicating superior performance of LiCo0.25 Ni0.75O2 over LiCoO2


  • Open Access

    Blended Copper and Nano-Silver Screen-Printed Circuits on FTO-Coated Glass

    by Bahaa Abbas, Eifion Jewell, Justin Searle

    Using a mixture of micro-copper and nano-silver in the production of screen-printed circuits has the potential to reduce material costs and cost variability. The fundamental premise of this study involved dispersing silver nanoparticles among the larger copper microparticles at selected ratios and subsequently sintering in order to establish their resultant electrical and physical performance. Commercial materials were mixed, printed, and sintered at two thermal regimes on fluorine-doped tin oxide (FTO)-coated glass substrate. The inclusion of 25% silver provided an appreciable reduction in electrical resistance from 4.21 Ω to 0.93 Ω, with further silver additions having less impact. The thermal regime used for sintering had a secondary impact on the final electrical performance. The addition of silver reduced the adhesion to the FTO substrate, with reduced film integrity. The results show that blending inks offers the advantage of enhancing material conductivity while simultaneously reducing costs, making it a compelling area for exploration and advancement in the field of electronics manufacturing.


  • Open Access

    Photonic sintering of copper for rapid processing of thick film conducting circuits on FTO coated glass

    by Bahaa Abbas, Eifion Jewell, Yin Cheung Lau, Justin Searle, Tim Claypole

    Copper potentially provides a cost-effective replacement for silver in printed electronic circuitry with diverse applications in healthcare, solar energy, IOT devices and automotive applications. The primary challenge facing copper is that it readily oxidizes to its non-conductive state during the sintering process. Photonic sintering offers a means of overcoming the oxidation by which rapid conversion from discrete nano-micro particles to fully or partially sintered products occurs. An experimental study of flash lamp sintering of mixed nano copper and mixed nano/ micro copper thick film screen printed structures on FTO coated glass was carried out. It shows that there may be multiple energy windows which can successfully sinter the thick film copper print preventing detrimental copper oxidation. Under optimum conditions, the conductivities achieved in under 1 s was (3.11–4.3 × 10–7 Ω m) matched those achieved in 90 min at 250 °C under reducing gas conditions, offering a significant improvement in productivity and reduced energy demand. Also present a good film stability of a 14% increase in line resistance of 100 N material, around 10% for the 50N50M ink and only around 2% for the 20N80M.


  • Open Access

    Developing capacity sharing strategy for vehicular networks with integrated use of licensed and unlicensed spectrum

    by Haider Albonda, Kadhum Al-Majdi, Bahaa Abbas

    A widely deployed cellular network, supported by direct connections, can offer a promising solution that supports new services with strict requirements on access availability, reliability, and end-to-end (E2E) latency. The communications between vehicles can be made using different radio interfaces: One for cellular communication (i.e., cellular communication over the cellular network based on uplink (UL)/downlink (DL) connections) and the other for direct communication (i.e., D2D-based direct communications between vehicles which allows vehicular users (V-UEs) to communicate directly with others). Common cellular systems with licensed spectrum backed by direct communication using unlicensed spectrum can ensure high quality of service requirements for new intelligent transportation systems (ITS) services, increase network capacity and reduce overall delays. However, selecting a convenient radio interface and allocating radio resources to users according to the quality of service (QoS) requirements becomes a challenge. In this regard, let’s introduce a new radio resource allocation strategy to determine when it’s appropriate to establish the communication between the vehicles over a cellular network using licensed spectrum resources or D2D-based direct connections over unlicensed spectrum sharing with Wi-Fi. The proposed strategy aims at meeting the quality of service requirements of users, including reducing the possibility of exceeding the maximum delay restrictions and enhancing network capacity utilization in order to avoid service interruption. The proposed solution is evaluated by highlighting different conditions for the considered scenario, and it is demonstrated that the proposed strategy improves network performance in terms of transmitted data rate, packet success rate, latency, and resource usage


  • Open Access

    Assessing the Dynamic Performance of Thermochemical Storage Materials

    by Sara Walsh, Jack Reynolds, Bahaa Abbas, Rachel Woods, Justin Searle, Eifion Jewell, Jonathon Elvins

    Thermochemical storage provides a volumetric and cost-efficient means of collecting energy from solar/waste heat in order to utilize it for space heating in another location. Equally important to the storage density, the dynamic thermal response dictates the power available which is critical to meet the varied demands of a practical space heating application. Using a laboratory scale reactor (127 cm3), an experimental study with salt in matrix (SIM) materials found that the reactor power response is primarily governed by the flow rate of moist air through the reactor and that creating salt with a higher salt fraction had minimal impact on the thermal response. The flowrate dictates the power profile of the reactor with an optimum value which balances moisture reactant delivery and reaction rate on the SIM. A mixed particle size produced the highest power (22 W) and peak thermal uplift (32 °C). A narrow particle range reduced the peak power and peak temperature as a result of lower packing densities of the SIM in the reactor. The scaled maximum power density which could be achieved is >150 kW/m3, but achieving this would require optimization of the solid–moist air interactions.