Danil V. Perevozchikov
Research Subjects
Danil V. Perevozchikov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandr N. Makoveckii
PJSC “ChelPipe”, Mashinostroiteley Str. 21, Chelyabinsk 454129, Russia
2 shared publications - Alexander M. Akhmedyanov
South Ural State University (National Research University), Chelyabinsk, Russia
2 shared publications - Liudmila V. Radionova
Moscow Polytechnic University
2 shared publications - Sergey V. Rushchits
South Ural State University (National Research University), Chelyabinsk, Russia
2 shared publications - Victor N. Eremin
PJSC “ChelPipe”, Mashinostroiteley Str. 21, Chelyabinsk 454129, Russia
2 shared publications
Latest Publications
- Open Access
Grain Growth during Mechanical Processing of Austenitic Stainless Steel AISI 321
The kinetics of austenite grain growth during thermomechanical treatment of AISI 321 steel with a relatively high content of carbon (0.07 wt. %) and titanium (0.50 wt. %) were studied. Hot deformation was carried out by the uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. A dependence is obtained for calculating the kinetics of austenite grain growth for a temperature range of 1150–1250 °C. The proposed dependence makes it possible to evaluate grain growth under non-isothermal conditions. The verification of the adequacy of the proposed dependence and the method for calculating the grain size at cooling rates 0.2, 1 and 5 °C/s showed its high convergence. The difference between the calculated and experimental grain size did not exceed 8%. The suppression of grain growth is due to the precipitation of titanium carbides and carbonitrides. Using the developed grain growth model, an analysis was made of the reasons for the formation of large grains in the shell after the elongating in the production process.
Open AccessGrain Growth during Mechanical Processing of Austenitic Stainless Steel AISI 321
The kinetics of austenite grain growth during thermomechanical treatment of AISI 321 steel with a relatively high content of carbon (0.07 wt. %) and titanium (0.50 wt. %) were studied. Hot deformation was carried out by the uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. A dependence is obtained for calculating the kinetics of austenite grain growth for a temperature range of 1150–1250 °C. The proposed dependence makes it possible to evaluate grain growth under non-isothermal conditions. The verification of the adequacy of the proposed dependence and the method for calculating the grain size at cooling rates 0.2, 1 and 5 °C/s showed its high convergence. The difference between the calculated and experimental grain size did not exceed 8%. The suppression of grain growth is due to the precipitation of titanium carbides and carbonitrides. Using the developed grain growth model, an analysis was made of the reasons for the formation of large grains in the shell after the elongating in the production process.
- Open Access
Study on the Hot Deformation Behavior of Stainless Steel AISI 321
In this study, the hot deformation behavior of austenitic Ti-modified AISI 321 steel with a relatively high content of carbon (0.07 wt.%) and titanium (0.50 wt.%) was studied in the temperature range of 1000–1280 °C and strain rates in the range of 0.01–1 s−1. Hot deformation was carried out with uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. It is shown that the flow stress increased with a decrease in the deformation temperature and an increase in the strain rate. The shape of the stress-strain curves indicates that, at high temperatures and low strain rates, the hot deformation of AISI 321 steel was accompanied by dynamic recrystallization. The passage of dynamic recrystallization was confirmed by microstructural studies. Hyperbolic sine type of constitutive equation with deformation activation energy Q = 444.2 kJ·mol−1 was established by analyzing the experimental flow stresses. The power-law dependences of the critical strain necessary for the onset of dynamic recrystallization and the size of recrystallized grains on the Zener–Hollomon parameter were established. The value of the parameter Z = 5.6 × 1015 was determined, above which the dynamic recrystallization was abruptly suppressed in the steel under study. It is speculated that the suppression of dynamic recrystallization occurs due to dispersed precipitates of titanium carbonitrides.
Open AccessStudy on the Hot Deformation Behavior of Stainless Steel AISI 321
In this study, the hot deformation behavior of austenitic Ti-modified AISI 321 steel with a relatively high content of carbon (0.07 wt.%) and titanium (0.50 wt.%) was studied in the temperature range of 1000–1280 °C and strain rates in the range of 0.01–1 s−1. Hot deformation was carried out with uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. It is shown that the flow stress increased with a decrease in the deformation temperature and an increase in the strain rate. The shape of the stress-strain curves indicates that, at high temperatures and low strain rates, the hot deformation of AISI 321 steel was accompanied by dynamic recrystallization. The passage of dynamic recrystallization was confirmed by microstructural studies. Hyperbolic sine type of constitutive equation with deformation activation energy Q = 444.2 kJ·mol−1 was established by analyzing the experimental flow stresses. The power-law dependences of the critical strain necessary for the onset of dynamic recrystallization and the size of recrystallized grains on the Zener–Hollomon parameter were established. The value of the parameter Z = 5.6 × 1015 was determined, above which the dynamic recrystallization was abruptly suppressed in the steel under study. It is speculated that the suppression of dynamic recrystallization occurs due to dispersed precipitates of titanium carbonitrides.