Vasiliy V. Mishakin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vasiliy V. Mishakin has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Vyacheslav Alexandrovich Klyushnikov
Mechanical Engineering Research Institute, Branch of Federal Research Center Institute of Applied Physics of the Russian Academy of Sciences, Nizhny Novgorod, Russia
23 shared publications - Alexander Victorovich Gonchar
Gaponov-Grekhov Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod, Russia
17 shared publications - Konstantin Vladimirovich Kurashkin
Russian Academy of Sciences
9 shared publications A. V. Gonchar
Mechanical Engineering Research Institute of the Russian Academy of Sciences, Branch of the Federal Research Center Institute of Applied Physics of the Russian Academy of Sciences, Nizhny Novgorod, Russia
5 shared publicationsV. A. Klyushnikov
Mechanical Engineering Research Institute of RAS Branch of Federal State Budgetary Scientific Institution “Federal Research Center the Institute of Applied Physics of the RAS”, Nizhny Novgorod, Russia
4 shared publicationsS. V. Kirikov
Mechanical Engineering Research Institute of RAS Branch of Federal State Budgetary Scientific Institution “Federal Research Center the Institute of Applied Physics of the RAS”, Nizhny Novgorod, Russia
3 shared publications
Latest Publications
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 68 (S3) , S449-S456
Influence of Microcracks on Poisson’s Ratio during Plastic Deformation of Austenitic Steel
We researched the influence of damage accumulation on the Poisson’s ratio measured by echo-pulse acoustic method during plastic deformation of 12Kh18N10T steel. On the basis of the obtained experimental data we calculated the partial contributions to the change in the Poisson’s ratio of damage accumulation and formation of the strain induced martensite phase. The characteristics of stable cracks forming near strain-induced martensite particles at small degrees of plastic strain have been analyzed by computer simulation. The theoretical dependence of the change in the Poisson’s ratio due to crack formation during plastic deformation has been constructed. A good agreement between the experimental data and theoretical calculations has been obtained.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 68 (S3) , S449-S456
Influence of Microcracks on Poisson’s Ratio during Plastic Deformation of Austenitic Steel
We researched the influence of damage accumulation on the Poisson’s ratio measured by echo-pulse acoustic method during plastic deformation of 12Kh18N10T steel. On the basis of the obtained experimental data we calculated the partial contributions to the change in the Poisson’s ratio of damage accumulation and formation of the strain induced martensite phase. The characteristics of stable cracks forming near strain-induced martensite particles at small degrees of plastic strain have been analyzed by computer simulation. The theoretical dependence of the change in the Poisson’s ratio due to crack formation during plastic deformation has been constructed. A good agreement between the experimental data and theoretical calculations has been obtained.
- 1 January 2022
- Published by Pleiades Publishing Ltd in Physical Mesomechanics
- Vol. 25 (1) , 80-84
Change in Texture-Dependent Acoustic Birefringence in α-Fe and γ-Fe Polycrystalline Aggregates due to Plastic Deformation
This paper deals with the investigation of crystallographic texture evolution and the associated change in acoustic birefringence during plastic deformation under uniaxial tension of metal alloy. Results of computer simulation for orthotropic α-Fe and γ-Fe polycrystalline aggregates are compared with experimental data for different steels. The increment in acoustic birefringence of shear elastic waves caused by changes in the elastic properties due to plastic deformation is found to be positive for the α-Fe polycrystalline aggregate with a bcc lattice and negative for the γ-Fe one with a fcc lattice. This effect is concluded to be associated with the difference between bcc and fcc lattices, having different slip planes and slip directions. Scattering of initial orthotropic texture and critical shear stress are also found to affect the changes in the effective elastic properties and, accordingly, the quantitative increment in acoustic birefringence. The mentioned factors should be taken into account when assessing damage of metal alloy by the acoustic birefringence technique.
- 1 January 2022
- Published by Pleiades Publishing Ltd in Physical Mesomechanics
- Vol. 25 (1) , 80-84
Change in Texture-Dependent Acoustic Birefringence in α-Fe and γ-Fe Polycrystalline Aggregates due to Plastic Deformation
This paper deals with the investigation of crystallographic texture evolution and the associated change in acoustic birefringence during plastic deformation under uniaxial tension of metal alloy. Results of computer simulation for orthotropic α-Fe and γ-Fe polycrystalline aggregates are compared with experimental data for different steels. The increment in acoustic birefringence of shear elastic waves caused by changes in the elastic properties due to plastic deformation is found to be positive for the α-Fe polycrystalline aggregate with a bcc lattice and negative for the γ-Fe one with a fcc lattice. This effect is concluded to be associated with the difference between bcc and fcc lattices, having different slip planes and slip directions. Scattering of initial orthotropic texture and critical shear stress are also found to affect the changes in the effective elastic properties and, accordingly, the quantitative increment in acoustic birefringence. The mentioned factors should be taken into account when assessing damage of metal alloy by the acoustic birefringence technique.
- Open Access
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 92 (3) , 405
Влияние микротрещин на коэффициент Пуассона при пластическом деформировании аустенитной стали
Влияние микротрещин на коэффициент Пуассона при пластическом деформировании аустенитной стали
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 92 (3) , 405
Open AccessВлияние микротрещин на коэффициент Пуассона при пластическом деформировании аустенитной стали
Влияние микротрещин на коэффициент Пуассона при пластическом деформировании аустенитной стали
- Open Access
- 1 September 2021
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 57 (9) , 823
Erratum to: Ultrasonic and Eddy-Current Fatigue Monitoring of Austenitic Steel Welded Joints
An Erratum to this paper has been published: https://doi.org/10.1134/S1061830921090126
- 1 September 2021
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 57 (9) , 823
Open AccessErratum to: Ultrasonic and Eddy-Current Fatigue Monitoring of Austenitic Steel Welded Joints
An Erratum to this paper has been published: https://doi.org/10.1134/S1061830921090126
- Open Access
- 1 July 2021
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 57 (7) , 570-578
Ultrasonic and Eddy-Current Fatigue Monitoring of Austenitic Steel Welded Joints
We investigated the process of fatigue damage in welded joints made of austenitic steel by ultrasonic and eddy current types of testing. The development of an inhomogeneity in the distribution of the acoustic anisotropy parameter in the heat-affected zone and in the base material was studied. As a result of eddy current testing, the difference in the intensity of changes in the phase composition in the heat-affected zone and in the base material is shown. A linear relationship is obtained between the amplitude of the cycle deformation under regular loading in the low-cycle fatigue region and the critical value of the percentage of the magnetic phase in the base material. A method is proposed for assessing the fatigue damage to the material of welded joints in the heat-affected zone based on the results of eddy current testing.
- 1 July 2021
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 57 (7) , 570-578
Open AccessUltrasonic and Eddy-Current Fatigue Monitoring of Austenitic Steel Welded Joints
We investigated the process of fatigue damage in welded joints made of austenitic steel by ultrasonic and eddy current types of testing. The development of an inhomogeneity in the distribution of the acoustic anisotropy parameter in the heat-affected zone and in the base material was studied. As a result of eddy current testing, the difference in the intensity of changes in the phase composition in the heat-affected zone and in the base material is shown. A linear relationship is obtained between the amplitude of the cycle deformation under regular loading in the low-cycle fatigue region and the critical value of the percentage of the magnetic phase in the base material. A method is proposed for assessing the fatigue damage to the material of welded joints in the heat-affected zone based on the results of eddy current testing.
- 1 May 2021
- Published by Springer Nature in Measurement Techniques
- Vol. 64 (2) , 145-150
Monitoring the State of Stainless Steel under Cyclic Deformation by the Acoustic and Eddy Current Methods
- 1 May 2021
- Published by Springer Nature in Measurement Techniques
- Vol. 64 (2) , 145-150
Monitoring the State of Stainless Steel under Cyclic Deformation by the Acoustic and Eddy Current Methods
- 4 January 2021
- Published by Springer Nature in Power Technology and Engineering
- Vol. 54 (5) , 642-650
Improving the Reliability of Hydrogenerators after an Extended Period of Operation
- 4 January 2021
- Published by Springer Nature in Power Technology and Engineering
- Vol. 54 (5) , 642-650
Improving the Reliability of Hydrogenerators after an Extended Period of Operation
- 1 January 2021
- Published by Federal Budgetary Institution "Research Center for Applied Metrology - Rostest" in Izmeritel`naya Tekhnika
- No. 2
The control of the condition of the stainless steel under cyclic loading by acoustic and eddy current method
This paper presents the results of ultrasonic and eddy-current measurements of the characteristics of austenitic stainless steel AISI 321 under fatigue failure. The effect of the strain amplitude on the intensity of changes in elastic and magnetic properties is studied. The use of a combination of eddy current and ultrasonic measurements makes it possible to assess the state of steel AISI 321 under fatigue failure is shown. The technique for measuring ultrasonic parameters described in this paper allows us to register changes in the structural state of a material under fatigue failure long before the crack is formed. The eddy current method is used to determine the volume fraction of martensite with ferromagnetic properties. An algorithm is proposed for estimating the number of loading cycles and the operating time of metastable austenitic steel AISI 321 based on the data of ultrasonic and eddy current measurements.
- 1 January 2021
- Published by Federal Budgetary Institution "Research Center for Applied Metrology - Rostest" in Izmeritel`naya Tekhnika
- No. 2
The control of the condition of the stainless steel under cyclic loading by acoustic and eddy current method
This paper presents the results of ultrasonic and eddy-current measurements of the characteristics of austenitic stainless steel AISI 321 under fatigue failure. The effect of the strain amplitude on the intensity of changes in elastic and magnetic properties is studied. The use of a combination of eddy current and ultrasonic measurements makes it possible to assess the state of steel AISI 321 under fatigue failure is shown. The technique for measuring ultrasonic parameters described in this paper allows us to register changes in the structural state of a material under fatigue failure long before the crack is formed. The eddy current method is used to determine the volume fraction of martensite with ferromagnetic properties. An algorithm is proposed for estimating the number of loading cycles and the operating time of metastable austenitic steel AISI 321 based on the data of ultrasonic and eddy current measurements.
- 1 December 2020
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 56 (15) , 1453-1457
Effect of Plastic Deformation and Subsequent Heat Treatment on the Acoustic and Magnetic Properties of 12Kh18N10T Steel
This paper presents results from studies on the effect of plastic deformation and subsequent heat treatment on the acoustic and electromagnetic properties of 12Kh18N10T austenitic steel. Widely used in industry, 12Kh18N10T cryogenic corrosion-resistant austenitic steel is interesting because upon plastic deformation the martensitic phase within it occurs, which significantly changes the electromagnetic, elastic, and strength properties of the material. The formation of a new phase together with the process of plastic deformation affects the crystallographic texture of the alloy, which impacts such parameter as acoustic anisotropy. Changes in the magnetic properties connected with appearance of the ferromagnetic phase of martensite in the paramagnetic austenite matrix were detected with an eddy current ferrite meter. It is found that, at the initial stage of plastic deformation (uniaxial tension), the value of the acoustic anisotropy parameter decreases. Probably, this is connected with the fact that the change in the texture is more affected by the deformation of austenite than the formation of α′-martensite. Further deformation of the material causes more intense formation of the new phase and its impact on the crystallographic texture becomes predominant, which results in the increase in the parameter of acoustic anisotropy. It is also found that annealing of 12Kh18N10T pre-deformed stainless steel at temperatures of 350, 600, 700, and 1050°C decreases the parameter of acoustic anisotropy and the volume content of the magnetic phase. At the temperature of 600°C, the acoustic anisotropy of the material drops to zero, whereas at the temperature of 1050°C, the martensitic phase is completely disintegrated and the texture is determined only by the austenitic phase.
- 1 December 2020
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 56 (15) , 1453-1457
Effect of Plastic Deformation and Subsequent Heat Treatment on the Acoustic and Magnetic Properties of 12Kh18N10T Steel
This paper presents results from studies on the effect of plastic deformation and subsequent heat treatment on the acoustic and electromagnetic properties of 12Kh18N10T austenitic steel. Widely used in industry, 12Kh18N10T cryogenic corrosion-resistant austenitic steel is interesting because upon plastic deformation the martensitic phase within it occurs, which significantly changes the electromagnetic, elastic, and strength properties of the material. The formation of a new phase together with the process of plastic deformation affects the crystallographic texture of the alloy, which impacts such parameter as acoustic anisotropy. Changes in the magnetic properties connected with appearance of the ferromagnetic phase of martensite in the paramagnetic austenite matrix were detected with an eddy current ferrite meter. It is found that, at the initial stage of plastic deformation (uniaxial tension), the value of the acoustic anisotropy parameter decreases. Probably, this is connected with the fact that the change in the texture is more affected by the deformation of austenite than the formation of α′-martensite. Further deformation of the material causes more intense formation of the new phase and its impact on the crystallographic texture becomes predominant, which results in the increase in the parameter of acoustic anisotropy. It is also found that annealing of 12Kh18N10T pre-deformed stainless steel at temperatures of 350, 600, 700, and 1050°C decreases the parameter of acoustic anisotropy and the volume content of the magnetic phase. At the temperature of 600°C, the acoustic anisotropy of the material drops to zero, whereas at the temperature of 1050°C, the martensitic phase is completely disintegrated and the texture is determined only by the austenitic phase.
- 1 May 2020
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- No. 3,p. 19-28
Determination of hydrogen-induced damage by an acoustic method
The 13HFA corrosion- and cold-resistant steel is studied by an ultrasonic method after hydrogen absorption for 96, 192, and 288 hours. Within the framework of classical flaw detection, it was found that the formation of macrodefects occurs only at 288 hours of hydrogen absorption. In the study of the material by the spectral-acoustic method, it was found that, during hydrogen absorption for 96 and 192 hours, the signal spectrum changes. This indicates the formation of microdefects. It is shown that the determination of the damage by the conventional ultrasonic flaw detection method and the use of the spectral-acoustic method for the evaluation of fracture at the microlevel give more complete information on the state of the investigated alloys.
- 1 May 2020
- Published by Institute of Engineering Science, Ural Branch RAS in Diagnostics, Resource and Mechanics of materials and structures
- No. 3,p. 19-28
Determination of hydrogen-induced damage by an acoustic method
The 13HFA corrosion- and cold-resistant steel is studied by an ultrasonic method after hydrogen absorption for 96, 192, and 288 hours. Within the framework of classical flaw detection, it was found that the formation of macrodefects occurs only at 288 hours of hydrogen absorption. In the study of the material by the spectral-acoustic method, it was found that, during hydrogen absorption for 96 and 192 hours, the signal spectrum changes. This indicates the formation of microdefects. It is shown that the determination of the damage by the conventional ultrasonic flaw detection method and the use of the spectral-acoustic method for the evaluation of fracture at the microlevel give more complete information on the state of the investigated alloys.