Xuan Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xuan Li has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hu Huang
Jilin University
9 shared publications - Zhi Xu
Key Laboratory of CNC Equipment Reliability, Ministry of Education, School of Mechanical and Aerospace Engineering, Jilin University, Changchun, Jilin, China
8 shared publications - Haoxiang Wu
Key Laboratory of CNC Equipment Reliability, Ministry of Education, School of Mechanical and Aerospace Engineering, Jilin University, Changchun, China
3 shared publications Wuxiang Sun
2 shared publications- Dayu Wei
Key Laboratory of CNC Equipment Reliability, Ministry of Education, School of Mechanical and Aerospace Engineering, Jilin University, Changchun, Jilin, China
1 shared publication - Hongwei Zhao
Jilin University
1 shared publication
Latest Publications
- 19 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (4) , 4030-4040
Achieving Highly Smooth and Linear Displacement Output of Stick-Slip Piezoelectric Actuators by an Active–Passive Collaborative Driving Method
Nonlinear one-step displacement and nonsmooth interstep transitions are commonly observed in nonresonant stepping piezoelectric actuators, which deviate from the desired smooth and linear displacement output and pose challenges for subsequent control strategies. At present, the generation of highly smooth and linear displacement output remains arduous, especially under various horizontal loads and preload deformations. To solve this problem, a method of active–passive collaborative driving (APCD) was proposed. Based on this method, a stick-slip piezoelectric actuator was developed, and the corresponding dynamic model was established. Then, a series of experimental tests were performed. Results demonstrated the feasibility of the APCD method in achieving highly smooth and linear displacement output. Notably, the actuator employing the APCD method demonstrated smooth and linear motion across horizontal loads from 0 g to 30 g, preload deformations from 0 mm to 0.5 mm and phase differences from 140 to 200 degrees. Furthermore, the actuator showed superior motion characteristics including high smoothness, linearity, stability, and consistency under various vertical loads and preload deformations, as well as excellent performances in terms of smoothness, linearity, and stability across a range of voltages and frequencies.
- 19 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (4) , 4030-4040
Achieving Highly Smooth and Linear Displacement Output of Stick-Slip Piezoelectric Actuators by an Active–Passive Collaborative Driving Method
Nonlinear one-step displacement and nonsmooth interstep transitions are commonly observed in nonresonant stepping piezoelectric actuators, which deviate from the desired smooth and linear displacement output and pose challenges for subsequent control strategies. At present, the generation of highly smooth and linear displacement output remains arduous, especially under various horizontal loads and preload deformations. To solve this problem, a method of active–passive collaborative driving (APCD) was proposed. Based on this method, a stick-slip piezoelectric actuator was developed, and the corresponding dynamic model was established. Then, a series of experimental tests were performed. Results demonstrated the feasibility of the APCD method in achieving highly smooth and linear displacement output. Notably, the actuator employing the APCD method demonstrated smooth and linear motion across horizontal loads from 0 g to 30 g, preload deformations from 0 mm to 0.5 mm and phase differences from 140 to 200 degrees. Furthermore, the actuator showed superior motion characteristics including high smoothness, linearity, stability, and consistency under various vertical loads and preload deformations, as well as excellent performances in terms of smoothness, linearity, and stability across a range of voltages and frequencies.
- 29 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 16275-16285
An Impact Inertial Piezoelectric Actuator With High Thrust-Weight Ratio Driven by Coupling the Inertial Force and Friction Force
Impact inertial piezoelectric actuators are favored with their simple control and structure, high resolution, etc. However, achieving a high thrust–weight ratio remains a challenge due to the positive correlation between the thrust force and inertial mass. To address this issue, an impact inertial piezoelectric actuator driven by coupling the inertial force and friction force is proposed in this article. Then, the corresponding structural design, operating principle, force analysis of the motion process, and parameter determination of the actuator were discussed in detail. An actuator prototype with the size of 32 × 29.4 × 6 mm 3 and mass of 8.2 g was manufactured, and a series of tests were performed under various preload deformations, voltages, frequencies, and loads. The experimental results showed that the actuator driven by coupling the inertial force and friction force could effectively enhance the thrust–weight ratio, and it achieved a maximum thrust–weight ratio of 54.42, far surpassing other actuators of the same type. Meanwhile, the actuator exhibited a maximum thrust force of 4.46 N, comparable to actuators with larger inertial masses. Furthermore, the actuator possessed excellent frequency stability and good adaptability in the motion angle and preload deformation.
- 29 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 16275-16285
An Impact Inertial Piezoelectric Actuator With High Thrust-Weight Ratio Driven by Coupling the Inertial Force and Friction Force
Impact inertial piezoelectric actuators are favored with their simple control and structure, high resolution, etc. However, achieving a high thrust–weight ratio remains a challenge due to the positive correlation between the thrust force and inertial mass. To address this issue, an impact inertial piezoelectric actuator driven by coupling the inertial force and friction force is proposed in this article. Then, the corresponding structural design, operating principle, force analysis of the motion process, and parameter determination of the actuator were discussed in detail. An actuator prototype with the size of 32 × 29.4 × 6 mm 3 and mass of 8.2 g was manufactured, and a series of tests were performed under various preload deformations, voltages, frequencies, and loads. The experimental results showed that the actuator driven by coupling the inertial force and friction force could effectively enhance the thrust–weight ratio, and it achieved a maximum thrust–weight ratio of 54.42, far surpassing other actuators of the same type. Meanwhile, the actuator exhibited a maximum thrust force of 4.46 N, comparable to actuators with larger inertial masses. Furthermore, the actuator possessed excellent frequency stability and good adaptability in the motion angle and preload deformation.
- 8 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (11) , 15190-15199
Development of a Vibration-Assisted Micro/Nano Scratch Tester for Evaluating the Scratch Behaviors of Materials Under Vibration Environment
Micro/nano scratch testing is an effective technique for characterizing the mechanical properties and wear resistance of materials. In practical applications, most of the materials in equipment serve in a vibration environment. However, the scratching characteristics of materials under vibration environment have not been well investigated due to the lack of suitable testing instruments. To address this issue, in this article, we develop a vibration-assisted micro/nano scratch tester. Its working principle is introduced, followed by designing and analyzing the vibration platform. Then, the prototype is fabricated and a control system is established. After that, the key performance parameters of the tester are characterized. The results showed that the load noise is lower than 0.1 mN, and the vibration platform can generate a unidirectional vibration with the amplitude range of 0.2–11 μm and frequency range of 1–2000 Hz. To verify the feasibility of the proposed scratch tester, vibration-assisted scratch tests are performed on AL1050. It is shown that vibration during scratch testing leads to an increase in the residual scratch width and a decrease in the coefficient of friction and scratch hardness. These findings verify the effectiveness of the vibration-assisted micro/nano scratch tester and highlight the significance of considering vibration effects on the characterization of materials.
- 8 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (11) , 15190-15199
Development of a Vibration-Assisted Micro/Nano Scratch Tester for Evaluating the Scratch Behaviors of Materials Under Vibration Environment
Micro/nano scratch testing is an effective technique for characterizing the mechanical properties and wear resistance of materials. In practical applications, most of the materials in equipment serve in a vibration environment. However, the scratching characteristics of materials under vibration environment have not been well investigated due to the lack of suitable testing instruments. To address this issue, in this article, we develop a vibration-assisted micro/nano scratch tester. Its working principle is introduced, followed by designing and analyzing the vibration platform. Then, the prototype is fabricated and a control system is established. After that, the key performance parameters of the tester are characterized. The results showed that the load noise is lower than 0.1 mN, and the vibration platform can generate a unidirectional vibration with the amplitude range of 0.2–11 μm and frequency range of 1–2000 Hz. To verify the feasibility of the proposed scratch tester, vibration-assisted scratch tests are performed on AL1050. It is shown that vibration during scratch testing leads to an increase in the residual scratch width and a decrease in the coefficient of friction and scratch hardness. These findings verify the effectiveness of the vibration-assisted micro/nano scratch tester and highlight the significance of considering vibration effects on the characterization of materials.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (10) , 12835-12845
Achieving Stable and Effective Stick-Slip Motions of Piezoelectric Actuators With a Small Mass Rotor by Means of the Auxiliary Friction
Stick-slip piezoelectric actuators are favored by precision instruments owing to their high resolution, fast response, etc. However, they face challenges when it comes to achieving effective output of the actuators with small mass rotor due to the offset of the forward angle by the backward angle. Aiming to achieve stable and effective stick-slip motion, a method that employs auxiliary friction was proposed, and accordingly, a stick-slip actuator was designed. Then, the feasibility of the auxiliary friction method was proved by comparing the theoretical analysis results of the output performances for the actuator with and without auxiliary friction. An experimental prototype with the rotor mass of 2 g was developed to test its output performances. Under 10 Hz and 100 V, the actuator with auxiliary friction exhibited a top torque of 3.85 N·mm, which was 55 times that of the actuator without auxiliary friction. Moreover, the actuator demonstrated a resolution of 1.2 μrad and a speed of 367.5 mrad/s. Experimental results showed that the auxiliary friction method could assist the actuator in achieving stable and effective stick-slip motion, thereby broadening its practical applications.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (10) , 12835-12845
Achieving Stable and Effective Stick-Slip Motions of Piezoelectric Actuators With a Small Mass Rotor by Means of the Auxiliary Friction
Stick-slip piezoelectric actuators are favored by precision instruments owing to their high resolution, fast response, etc. However, they face challenges when it comes to achieving effective output of the actuators with small mass rotor due to the offset of the forward angle by the backward angle. Aiming to achieve stable and effective stick-slip motion, a method that employs auxiliary friction was proposed, and accordingly, a stick-slip actuator was designed. Then, the feasibility of the auxiliary friction method was proved by comparing the theoretical analysis results of the output performances for the actuator with and without auxiliary friction. An experimental prototype with the rotor mass of 2 g was developed to test its output performances. Under 10 Hz and 100 V, the actuator with auxiliary friction exhibited a top torque of 3.85 N·mm, which was 55 times that of the actuator without auxiliary friction. Moreover, the actuator demonstrated a resolution of 1.2 μrad and a speed of 367.5 mrad/s. Experimental results showed that the auxiliary friction method could assist the actuator in achieving stable and effective stick-slip motion, thereby broadening its practical applications.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11185-11194
On the Performance Improvement of a Miniature Impact Inertial Piezoelectric Actuator for Vertical Positioning
Miniature actuators enable precision positioning and micro-manipulation in space-constrained environments, which is essential in diverse industrial and scientific fields. The piezoelectric actuators represent one of the most advanced solutions for high precision motion output with miniaturized dimension and weight. However, high performance vertical positioning poses a challenge for the miniature piezoelectric actuators. In this article, a novel miniature impact inertial piezoelectric actuator (IIPA) capable of operating with multiple motion directions was proposed. The auxiliary friction method was applied to reduce the inertial mass, improve output performances, and enhance the self-locking force. The finite-element method was utilized to optimize the structure of the IIPA, and its dimensions and weight were determined as 15.6 mm × 16.2 mm × 2 mm and 2.7 g. Experimental results demonstrated that the IIPA not only achieved stable horizontal and vertical motions but also maintained a high degree of motion consistency across various motion directions. The design based on the auxiliary friction method is anticipated to be an advanced and alternative solution for miniature IIPAs with high performance vertical positioning capability.
- 28 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 11185-11194
On the Performance Improvement of a Miniature Impact Inertial Piezoelectric Actuator for Vertical Positioning
Miniature actuators enable precision positioning and micro-manipulation in space-constrained environments, which is essential in diverse industrial and scientific fields. The piezoelectric actuators represent one of the most advanced solutions for high precision motion output with miniaturized dimension and weight. However, high performance vertical positioning poses a challenge for the miniature piezoelectric actuators. In this article, a novel miniature impact inertial piezoelectric actuator (IIPA) capable of operating with multiple motion directions was proposed. The auxiliary friction method was applied to reduce the inertial mass, improve output performances, and enhance the self-locking force. The finite-element method was utilized to optimize the structure of the IIPA, and its dimensions and weight were determined as 15.6 mm × 16.2 mm × 2 mm and 2.7 g. Experimental results demonstrated that the IIPA not only achieved stable horizontal and vertical motions but also maintained a high degree of motion consistency across various motion directions. The design based on the auxiliary friction method is anticipated to be an advanced and alternative solution for miniature IIPAs with high performance vertical positioning capability.
- 13 November 2022
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 240, 107933
A miniature impact drive mechanism with spatial interdigital structure
- 13 November 2022
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 240, 107933
A miniature impact drive mechanism with spatial interdigital structure
- 22 August 2022
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 233
A stick-slip piezoelectric actuator with high assembly interchangeability
- 22 August 2022
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 233
A stick-slip piezoelectric actuator with high assembly interchangeability
- Open Access
An Inertial Impact Piezoelectric Actuator Designed by the Asymmetric Friction Principle and Achieved by Laser Texturing of the Driving Feet
An asymmetric friction principle is newly proposed for the design of inertial impact piezoelectric actuators. There are two ways to achieve asymmetric frictions: either by tuning the positive pressure or by tuning the friction coefficient. Compared with tuning the positive pressure by an asymmetric structure, the structural parameters can be reduced by employing a symmetric structure and tuning the friction coefficient. In this study, an asymmetric friction inertial impact actuator was developed using a symmetric compliant mechanism (SCM), and the asymmetric frictions were realized by laser texturing of the driving feet at one end of the SCM. Four kinds of microstructures were initially fabricated on the driving feet, and their friction properties were experimentally tested. Accordingly, two kinds of microstructures, namely Ta and Tb microstructures, were selected. Output characteristics of the actuator with these two microstructures were measured and comparatively analyzed. The experimental results indicate that the actuator could achieve stable step motion, and the output characteristics were affected by the fabricated microstructure, as it determined the friction coefficient. The actuator with the Tb microstructure achieved a maximum speed of 2.523 mm/s, a resolution of 188 nm, a vertical loading capacity of 2 N and a horizontal loading capacity of 0.6 N, whereas the actuator with the Ta microstructure had a higher resolution of 74 nm. This study provides a novel idea for the design of asymmetric friction inertial impact actuators by tuning the friction coefficient.
Open AccessAn Inertial Impact Piezoelectric Actuator Designed by the Asymmetric Friction Principle and Achieved by Laser Texturing of the Driving Feet
An asymmetric friction principle is newly proposed for the design of inertial impact piezoelectric actuators. There are two ways to achieve asymmetric frictions: either by tuning the positive pressure or by tuning the friction coefficient. Compared with tuning the positive pressure by an asymmetric structure, the structural parameters can be reduced by employing a symmetric structure and tuning the friction coefficient. In this study, an asymmetric friction inertial impact actuator was developed using a symmetric compliant mechanism (SCM), and the asymmetric frictions were realized by laser texturing of the driving feet at one end of the SCM. Four kinds of microstructures were initially fabricated on the driving feet, and their friction properties were experimentally tested. Accordingly, two kinds of microstructures, namely Ta and Tb microstructures, were selected. Output characteristics of the actuator with these two microstructures were measured and comparatively analyzed. The experimental results indicate that the actuator could achieve stable step motion, and the output characteristics were affected by the fabricated microstructure, as it determined the friction coefficient. The actuator with the Tb microstructure achieved a maximum speed of 2.523 mm/s, a resolution of 188 nm, a vertical loading capacity of 2 N and a horizontal loading capacity of 0.6 N, whereas the actuator with the Ta microstructure had a higher resolution of 74 nm. This study provides a novel idea for the design of asymmetric friction inertial impact actuators by tuning the friction coefficient.