Ashok Kumar Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ashok Kumar Singh has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
Premkumar Manda
DMLS
11 shared publicationsT. K. Nandy
Defence Metallurgical Research Laboratory, Kanchanbagh, Hyderabad, India
6 shared publicationsAshutosh Panchal
Defence Metallurgical Research Laboratory, Kanchanbagh, Hyderabad, India
5 shared publicationsR. K. Mandal
IIT (BHU)
5 shared publicationsK. Venugopal Reddy
Department of Physics, NIT Warangal, Warangal, India
4 shared publicationsA. Sambasiva Rao
Defence Metallurgical Research Laboratory, Hyderabad, India
3 shared publications
Latest Publications
- Open Access
- 6 March 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (3) , 651-658
Studies on the Structural, Optical, Photocatalytic and Luminescence Properties of Monodispersed CdS Nanoparticles Capped with Moringa oleifera L. Leaf Extract
This study reports the structural, optical, photocatalytic and luminescence properties of monodispersed cadmium sulphide nanoparticles (CdS NPs) synthesised via an eco-friendly green synthesis approach using Moringa oleifera leaf extract as a natural stabilizing and capping agent. Cadmium nitrate, cadmium sulphate and cadmium chloride are used as cadmium precursors, while sodium sulphide served as the sulphur source. X-ray diffraction (XRD) analysis confirmed the formation of cubic-phase CdS NPs with high crystalline nature. The optical properties are evaluated through UV-Vis absorption spectroscopy, revealing a band gap energy range of 3.08 to 4.92 eV. FTIR confirmed the presence of functional groups responsible for stabilisation of CdS NPs. The morphological characteristics, elemental composition and purity are assessed using FESEM and EDS. Small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) determined the nanoparticle size to be below 5 nm, confirming their nanoscale dimensions. Photoluminescence (PL) spectra indicate strong emission properties, enhancing their potential use in optoelectronic applications. The photocatalytic activity of CdS NPs is evaluated by degrading methylene blue (MB) and rhodamine B (RhB) dyes under visible light irradiation, demonstrating their efficiency in environmental remediation and wastewater treatment. The results highlight the superior optical, structural and catalytic performance of M. oleifera-capped CdS NPs, making them promising candidates for advanced nanomaterial applications in solar cells, photocatalysis and biomedical fields.
- 6 March 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (3) , 651-658
Open AccessStudies on the Structural, Optical, Photocatalytic and Luminescence Properties of Monodispersed CdS Nanoparticles Capped with Moringa oleifera L. Leaf Extract
This study reports the structural, optical, photocatalytic and luminescence properties of monodispersed cadmium sulphide nanoparticles (CdS NPs) synthesised via an eco-friendly green synthesis approach using Moringa oleifera leaf extract as a natural stabilizing and capping agent. Cadmium nitrate, cadmium sulphate and cadmium chloride are used as cadmium precursors, while sodium sulphide served as the sulphur source. X-ray diffraction (XRD) analysis confirmed the formation of cubic-phase CdS NPs with high crystalline nature. The optical properties are evaluated through UV-Vis absorption spectroscopy, revealing a band gap energy range of 3.08 to 4.92 eV. FTIR confirmed the presence of functional groups responsible for stabilisation of CdS NPs. The morphological characteristics, elemental composition and purity are assessed using FESEM and EDS. Small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) determined the nanoparticle size to be below 5 nm, confirming their nanoscale dimensions. Photoluminescence (PL) spectra indicate strong emission properties, enhancing their potential use in optoelectronic applications. The photocatalytic activity of CdS NPs is evaluated by degrading methylene blue (MB) and rhodamine B (RhB) dyes under visible light irradiation, demonstrating their efficiency in environmental remediation and wastewater treatment. The results highlight the superior optical, structural and catalytic performance of M. oleifera-capped CdS NPs, making them promising candidates for advanced nanomaterial applications in solar cells, photocatalysis and biomedical fields.
- 11 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (2) , 659-666
Structure, processing, property correlation of metastable β titanium Ti-5Al-5Mo-5V-3Cr alloy
This work reports the evolution of “Structure, Processing, Property Correlation of Metastable β Titanium Ti-5Al-5Mo-5V-3Cr alloy” as a function of different aging temperatures (625,725 and 775 °C) for 4 h subsequent to solution heat treatment. The hot-rolled sheet was heat treated in β phase field and then water quenched. The solution heat treated in β phase field and then water quenched samples were aged at 625, 725 and 775 °C for 4 h. The hot-rolled sample shows the presence of α and β phases. The β-solution heat treated in β phase field and then water quenched sample of the alloy exhibits single β phase. The intensities of X-ray peaks are varying and β (211) peak shows the maximum intensity. The maximum intensity can be ascribed to β (211) texture. The solution heat treated in β phase field and then water quenched sample aged at 625 °C for 4 h shows the very fine hexagonal α phase precipitates as compared to the samples aged at 725 and 775 °C for 4 h. The samples aged at 725 and 775 °C for 4 h has resulted in precipitate-free zones as a result of the rejection of Mo, V, and Cr (β stabilizing elements) during nucleation and growth of α precipitates along the β grain boundaries. The Vickers hardness values of the alloy increase from solution heat treated in β phase field and then water quenched to all aging temperatures. The sample aged at 625 °C for 4 h shows the maximum hardness which is due to the presence of fine α phase precipitates. This can be ascribed to typical precipitation hardening.
- 11 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (2) , 659-666
Structure, processing, property correlation of metastable β titanium Ti-5Al-5Mo-5V-3Cr alloy
This work reports the evolution of “Structure, Processing, Property Correlation of Metastable β Titanium Ti-5Al-5Mo-5V-3Cr alloy” as a function of different aging temperatures (625,725 and 775 °C) for 4 h subsequent to solution heat treatment. The hot-rolled sheet was heat treated in β phase field and then water quenched. The solution heat treated in β phase field and then water quenched samples were aged at 625, 725 and 775 °C for 4 h. The hot-rolled sample shows the presence of α and β phases. The β-solution heat treated in β phase field and then water quenched sample of the alloy exhibits single β phase. The intensities of X-ray peaks are varying and β (211) peak shows the maximum intensity. The maximum intensity can be ascribed to β (211) texture. The solution heat treated in β phase field and then water quenched sample aged at 625 °C for 4 h shows the very fine hexagonal α phase precipitates as compared to the samples aged at 725 and 775 °C for 4 h. The samples aged at 725 and 775 °C for 4 h has resulted in precipitate-free zones as a result of the rejection of Mo, V, and Cr (β stabilizing elements) during nucleation and growth of α precipitates along the β grain boundaries. The Vickers hardness values of the alloy increase from solution heat treated in β phase field and then water quenched to all aging temperatures. The sample aged at 625 °C for 4 h shows the maximum hardness which is due to the presence of fine α phase precipitates. This can be ascribed to typical precipitation hardening.
- 20 June 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (2) , 576-584
On the development of gelcasting process for tungsten and its alloys
Gelcasting technique has been successfully used for the preparation of porous tungsten. Gel forming monomer (methacrylamide (MAM)) and Cross-linker (NN’-Methylenebisacrylamide (MBAM)) dissolved in water were used for gelcasting of green compacts of tungsten with 39% solid loading. Appropriate quantity of dispersant, initiator, and catalyst were used in order to obtain a uniform dispersion of tungsten particles and also control the polymerization process. Several issues related to dispersant selection, de-airing, de-bindering, sintering, and selection of mold material have been addressed in order to obtain a defect-free product. Theoretical density of the porous sintered tungsten pellets produced by gelcasting process is ∼85%. The average pore diameter and mean pore area are 3 µm and 16 µm 2 , respectively, which are specifically required for the cathode application. Complex shape components of pure tungsten have been successfully made using gelcasting technique for the first time.
- 20 June 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (2) , 576-584
On the development of gelcasting process for tungsten and its alloys
Gelcasting technique has been successfully used for the preparation of porous tungsten. Gel forming monomer (methacrylamide (MAM)) and Cross-linker (NN’-Methylenebisacrylamide (MBAM)) dissolved in water were used for gelcasting of green compacts of tungsten with 39% solid loading. Appropriate quantity of dispersant, initiator, and catalyst were used in order to obtain a uniform dispersion of tungsten particles and also control the polymerization process. Several issues related to dispersant selection, de-airing, de-bindering, sintering, and selection of mold material have been addressed in order to obtain a defect-free product. Theoretical density of the porous sintered tungsten pellets produced by gelcasting process is ∼85%. The average pore diameter and mean pore area are 3 µm and 16 µm 2 , respectively, which are specifically required for the cathode application. Complex shape components of pure tungsten have been successfully made using gelcasting technique for the first time.
- 2 July 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup3) , 1924-1959
STRUCTURE - PROPERTY - PROCESSING CORRELATIONS IN METASTABLE BETA TITANIUM ALLOYS Ti-10V-2Fe-3Al AND Ti-5Al-5Mo-5V-3Cr
This paper describes the microstructure, texture and tensile properties of the two metastable β titanium alloys (Ti-10V-2Fe-3Al and Ti-5Al-5Mo-5V-3Cr). Both the alloys exhibit the single β (body centered cubic) phase in β solution treated and water quenched (β ST WQ) condition. The β ST WQ samples were aged at two different temperatures (550 and 750 °C) and different aging times (2, 4 and 6 hrs). The aging has resulted in different α phase morphologies of a phase precipitates. The sizes and volume fractions of the a phase increase and decrease with increase in aging temperature, respectively. The higher aging temperature (750 °C) results in precipitation free zones (PFZ) within the vicinity of prior β grain boundaries. The a phase texture is basal and it changes to non-basal with increase in aging time. The sharp a phase texture consists of {0001} || ND fibre with high intensity. The Vickers hardness values of both the alloys increase from β ST WQ to all aging temperatures due to precipitation hardening. The specimens aged at 550 °C have resulted in high strength in alloy Ti-1023. In contrast, 750 °C aged samples of both the alloys result in lower strength and moderate elongation values.
- 2 July 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup3) , 1924-1959
STRUCTURE - PROPERTY - PROCESSING CORRELATIONS IN METASTABLE BETA TITANIUM ALLOYS Ti-10V-2Fe-3Al AND Ti-5Al-5Mo-5V-3Cr
This paper describes the microstructure, texture and tensile properties of the two metastable β titanium alloys (Ti-10V-2Fe-3Al and Ti-5Al-5Mo-5V-3Cr). Both the alloys exhibit the single β (body centered cubic) phase in β solution treated and water quenched (β ST WQ) condition. The β ST WQ samples were aged at two different temperatures (550 and 750 °C) and different aging times (2, 4 and 6 hrs). The aging has resulted in different α phase morphologies of a phase precipitates. The sizes and volume fractions of the a phase increase and decrease with increase in aging temperature, respectively. The higher aging temperature (750 °C) results in precipitation free zones (PFZ) within the vicinity of prior β grain boundaries. The a phase texture is basal and it changes to non-basal with increase in aging time. The sharp a phase texture consists of {0001} || ND fibre with high intensity. The Vickers hardness values of both the alloys increase from β ST WQ to all aging temperatures due to precipitation hardening. The specimens aged at 550 °C have resulted in high strength in alloy Ti-1023. In contrast, 750 °C aged samples of both the alloys result in lower strength and moderate elongation values.
- 23 June 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup2) , 992-1006
On the development of porous nickel through gelcasting technique
In this study, a slurry-based technique has been developed for the manufacturing of porous nickel structures for capillary pumping systems. The application of porous Ni structures to capillary pumping systems requires porosity levels higher than 40% and pore size diameter lower than 20 μm. Irregular type open pores are observed in the sintered blanks. The porosity level and volume shrinkage decreases and increases with increase in sintering temperature, respectively. The compressive flow stress-strain curves exhibit three distinct regions namely, (i) linear region characterised by elastic modulus, (ii) corresponds to plastic yield and buckling of pore ligaments and (iii) densification region characterised by increasing slope. As the sintering temperature increases, porosity level decreases and resulting in increase in the plateau and densification stress.
- 23 June 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup2) , 992-1006
On the development of porous nickel through gelcasting technique
In this study, a slurry-based technique has been developed for the manufacturing of porous nickel structures for capillary pumping systems. The application of porous Ni structures to capillary pumping systems requires porosity levels higher than 40% and pore size diameter lower than 20 μm. Irregular type open pores are observed in the sintered blanks. The porosity level and volume shrinkage decreases and increases with increase in sintering temperature, respectively. The compressive flow stress-strain curves exhibit three distinct regions namely, (i) linear region characterised by elastic modulus, (ii) corresponds to plastic yield and buckling of pore ligaments and (iii) densification region characterised by increasing slope. As the sintering temperature increases, porosity level decreases and resulting in increase in the plateau and densification stress.
- 22 February 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (2) , 1916-1945
Microstructure, texture and mechanical properties of metastable beta titanium alloy Ti-5Al-5Mo-5V-3Cr
Present work describes the evolution of microstructure, texture and mechanical properties of the alloy Ti-5Al-5Mo-5 V-3Cr as a function of ageing temperatures and time intervals. The hot-rolled sheet of the pancake was solution treated in β phase field and water quenched (β ST WQ) and aged. The β ST WQ sample of the alloy exhibits single β phase. The β ST WQ samples were initially aged at 300°C for 30, 60 and 90 min and again aged at 550 and 750°C for different ageing times. The ageing has resulted in different morphologies of the α phase precipitates. These are grain boundary α, sub boundary α, islands α and uniform distribution of α within prior β grains. The sizes and volume fractions of the α phase increase and decrease with increase in ageing temperature, respectively. The higher ageing temperature (750°C) results in precipitation-free zone within the vicinity of prior β grain boundaries. . The basal texture observed in α phase of the aged samples exhibits moderate to high intensity along with {0001}||ND fibre. Non-basal textures in α phase have always weak/moderate intensity. The Vickers hardness values of the alloy increase from βSTWQ to all ageing temperatures due to precipitation hardening. The A2-550-4h sample exhibits no yielding due to fine α phase precipitates. On the other hand, A2-750-4h sample displays moderate elongation with high strength values. .
- 22 February 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (2) , 1916-1945
Microstructure, texture and mechanical properties of metastable beta titanium alloy Ti-5Al-5Mo-5V-3Cr
Present work describes the evolution of microstructure, texture and mechanical properties of the alloy Ti-5Al-5Mo-5 V-3Cr as a function of ageing temperatures and time intervals. The hot-rolled sheet of the pancake was solution treated in β phase field and water quenched (β ST WQ) and aged. The β ST WQ sample of the alloy exhibits single β phase. The β ST WQ samples were initially aged at 300°C for 30, 60 and 90 min and again aged at 550 and 750°C for different ageing times. The ageing has resulted in different morphologies of the α phase precipitates. These are grain boundary α, sub boundary α, islands α and uniform distribution of α within prior β grains. The sizes and volume fractions of the α phase increase and decrease with increase in ageing temperature, respectively. The higher ageing temperature (750°C) results in precipitation-free zone within the vicinity of prior β grain boundaries. . The basal texture observed in α phase of the aged samples exhibits moderate to high intensity along with {0001}||ND fibre. Non-basal textures in α phase have always weak/moderate intensity. The Vickers hardness values of the alloy increase from βSTWQ to all ageing temperatures due to precipitation hardening. The A2-550-4h sample exhibits no yielding due to fine α phase precipitates. On the other hand, A2-750-4h sample displays moderate elongation with high strength values. .
- 21 October 2020
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 9 (5) , 774-787
Microstructure, Tensile Flow and Work Hardening Behavior of W–Ni–Fe Alloys: Effect of Co and Co + Mo Additions
- 21 October 2020
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 9 (5) , 774-787
Microstructure, Tensile Flow and Work Hardening Behavior of W–Ni–Fe Alloys: Effect of Co and Co + Mo Additions
- 13 October 2020
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 101 (2) , 211-241
Effect of Ni/Fe ratio on microstructure, tensile flow and work hardening behaviour of tungsten heavy alloys in heat treated and swaged conditions
The present work describes the effect of Ni/Fe ratio on microstructure, tensile flow and work hardening behaviour of tungsten heavy alloys (WHAs) based on 92 wt. % W with varying Ni/Fe ratios in heat treated and swaged conditions. Evaluation of properties in the heat treated and swaged conditions reflect that the increasing Ni/Fe ratio has resulted in the enhancement of tensile as well as impact properties. Quantitative metallography and fractography have been conducted to identify the role of microstructural attributes on the failure behaviour in both the tensile and impact energy tests. The properties improvements at higher Ni/Fe ratios are due to the realisation of microstructure comprising relatively higher dissolved W in the matrix phase, higher volume fraction of matrix and reduced contiguity of W particles. True stress–true plastic strain curves of present alloys on log–log scale display two- and single-slopes in heat treated and swaged conditions, respectively. The instantaneous work hardening curves reveal the presence of three distinctive regimes (I, II and III) in heat treated and swaged conditions. The second derivatives of true stress–true plastic strain curves are parabola.
- 13 October 2020
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 101 (2) , 211-241
Effect of Ni/Fe ratio on microstructure, tensile flow and work hardening behaviour of tungsten heavy alloys in heat treated and swaged conditions
The present work describes the effect of Ni/Fe ratio on microstructure, tensile flow and work hardening behaviour of tungsten heavy alloys (WHAs) based on 92 wt. % W with varying Ni/Fe ratios in heat treated and swaged conditions. Evaluation of properties in the heat treated and swaged conditions reflect that the increasing Ni/Fe ratio has resulted in the enhancement of tensile as well as impact properties. Quantitative metallography and fractography have been conducted to identify the role of microstructural attributes on the failure behaviour in both the tensile and impact energy tests. The properties improvements at higher Ni/Fe ratios are due to the realisation of microstructure comprising relatively higher dissolved W in the matrix phase, higher volume fraction of matrix and reduced contiguity of W particles. True stress–true plastic strain curves of present alloys on log–log scale display two- and single-slopes in heat treated and swaged conditions, respectively. The instantaneous work hardening curves reveal the presence of three distinctive regimes (I, II and III) in heat treated and swaged conditions. The second derivatives of true stress–true plastic strain curves are parabola.
- 26 May 2020
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 9 (3) , 438-456
Microstructure, Texture, Tensile Flow and Work Hardening Behavior of Tungsten Heavy Alloys in Swaged and Swaged + Aged Conditions
- 26 May 2020
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 9 (3) , 438-456
Microstructure, Texture, Tensile Flow and Work Hardening Behavior of Tungsten Heavy Alloys in Swaged and Swaged + Aged Conditions
- 19 February 2020
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 100 (11) , 1519-1538
Instantaneous work hardening behaviour of two-phase tungsten heavy alloys: a phenomenological approach
The present work describes a phenomenological approach to explain the instantaneous behaviour of tungsten heavy alloys (WHAs) in heat-treated and swaged conditions. The strengths and elongation values of heat-treated materials are lower and higher than those of the swaged samples respectively. The heat-treated materials exhibit two slopes in true stress–true plastic strain curves and follow the Ludwigson constitutive equation. On the other hand, swaged materials display a single slope and adhere to typical Swift constitutive equation. The latter reflect the presence of pre-strain in the materials due to swaging deformation. The fracture surfaces in heat-treated materials consist of W-W decohesion along with matrix rupture and W-cleavage, while swaged samples consist of mainly W-cleavage. Both the materials display three typical stages (I, II and III) of work hardening. The second derivatives of true stress–true plastic strain curves of these alloys exhibit a perfect parabola although the nature of true stress–true strain as well as true stress–true plastic strain curves is quite different in heat-treated and swaged materials. This has been observed for the first time in WHAs consisting of matrix and W-grains. The shape of the parabola is simple and easy to fit. The fitting parameters of parabolas have been successfully employed to explain the flow behaviour of a large number of tungsten heavy alloys having two-phase microstructure in different processing conditions.
- 19 February 2020
- Published by Taylor & Francis in Philosophical Magazine
- Vol. 100 (11) , 1519-1538
Instantaneous work hardening behaviour of two-phase tungsten heavy alloys: a phenomenological approach
The present work describes a phenomenological approach to explain the instantaneous behaviour of tungsten heavy alloys (WHAs) in heat-treated and swaged conditions. The strengths and elongation values of heat-treated materials are lower and higher than those of the swaged samples respectively. The heat-treated materials exhibit two slopes in true stress–true plastic strain curves and follow the Ludwigson constitutive equation. On the other hand, swaged materials display a single slope and adhere to typical Swift constitutive equation. The latter reflect the presence of pre-strain in the materials due to swaging deformation. The fracture surfaces in heat-treated materials consist of W-W decohesion along with matrix rupture and W-cleavage, while swaged samples consist of mainly W-cleavage. Both the materials display three typical stages (I, II and III) of work hardening. The second derivatives of true stress–true plastic strain curves of these alloys exhibit a perfect parabola although the nature of true stress–true strain as well as true stress–true plastic strain curves is quite different in heat-treated and swaged materials. This has been observed for the first time in WHAs consisting of matrix and W-grains. The shape of the parabola is simple and easy to fit. The fitting parameters of parabolas have been successfully employed to explain the flow behaviour of a large number of tungsten heavy alloys having two-phase microstructure in different processing conditions.