Resti Marlina
Research Subjects
Resti Marlina has a total of 119 co-authors. Here are the top co-authors by number of shared publications:
- Eka Nurfani
Department of Materials Engineering, Faculty of Industrial Technology, Institut Teknologi Sumatera (ITERA), South Lampung, Indonesia
10 shared publications - Nur Istiqomah Khamidy
Department of Materials Engineering, Faculty of Industrial Technology, Institut Teknologi Sumatera (ITERA), Lampung, 35365, Indonesia
5 shared publications - Robi Kurniawan
Universitas Negeri Malang
5 shared publications Yudi Darma
5 shared publications- Jumaeda Jatmika
Research Center for Quantum Physics, National Research and Innovation Agency (BRIN) 1 , South Tangerang 15314
4 shared publications Yolanda Rati
4 shared publications
Latest Publications
- Open Access
- 11 October 2026
- Published by Green and Sustainable Materials Society in Greensusmater
- Vol. 3 (2)
Effect of Precursor-Solution pH on the Phase Composition and Microstructure of Precipitated NiO, and By-Product Retention in Hydrothermally Derived NiO–MnO2 Powders
Nickel oxide (NiO)/manganese dioxide (MnO2) composites are widely studied pseudocapacitive electrode materials, but the role of the precursor-solution pH in their synthesis is poorly established. NiO was precipitated at precursor pH 8, 9, 10, and 11, calcined, and subjected to a hydrothermal MnO2-growth step, and the products were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). Cubic NiO was the only Ni-bearing oxide, accompanied by a large halite (NaCl) by-product fraction (32–41 wt%). Scherrer, Williamson–Hall, and size–strain-plot analyses gave a NiO crystallite size of 20–30 nm and a microstrain near 1×10−3, and Nelson–Riley refinement gave a lattice parameter of 4.178 Å, equal to the bulk value; neither these quantities nor the NaCl content varied systematically with pH. The hydrothermal products were dominated by a phase indexed on a primitive cubic cell (a = 10.1175 Å) consistent with langbeinite-type K2Mn2(SO4)3; the reflections attributable to tetragonal MnO2 coincide with those of this phase, so MnO2 formation is not established. FE-SEM showed sheet- and flake-like features after the hydrothermal step, and EDS detected Ni, Mn, and O, but neither technique identifies the Mn-bearing phase. Over pH 8–11 the precursor pH is therefore not an effective processing variable: the retained by-products dominate the material, and purification, rather than pH, controls this route.
- 11 October 2026
- Published by Green and Sustainable Materials Society in Greensusmater
- Vol. 3 (2)
Open AccessEffect of Precursor-Solution pH on the Phase Composition and Microstructure of Precipitated NiO, and By-Product Retention in Hydrothermally Derived NiO–MnO2 Powders
Nickel oxide (NiO)/manganese dioxide (MnO2) composites are widely studied pseudocapacitive electrode materials, but the role of the precursor-solution pH in their synthesis is poorly established. NiO was precipitated at precursor pH 8, 9, 10, and 11, calcined, and subjected to a hydrothermal MnO2-growth step, and the products were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). Cubic NiO was the only Ni-bearing oxide, accompanied by a large halite (NaCl) by-product fraction (32–41 wt%). Scherrer, Williamson–Hall, and size–strain-plot analyses gave a NiO crystallite size of 20–30 nm and a microstrain near 1×10−3, and Nelson–Riley refinement gave a lattice parameter of 4.178 Å, equal to the bulk value; neither these quantities nor the NaCl content varied systematically with pH. The hydrothermal products were dominated by a phase indexed on a primitive cubic cell (a = 10.1175 Å) consistent with langbeinite-type K2Mn2(SO4)3; the reflections attributable to tetragonal MnO2 coincide with those of this phase, so MnO2 formation is not established. FE-SEM showed sheet- and flake-like features after the hydrothermal step, and EDS detected Ni, Mn, and O, but neither technique identifies the Mn-bearing phase. Over pH 8–11 the precursor pH is therefore not an effective processing variable: the retained by-products dominate the material, and purification, rather than pH, controls this route.
- 21 September 2026
- Published by Elsevier in Journal of Alloys and Compounds Communications
- Vol. 12
Influence of mineralizers on the phase evolution and surface defect chemistry of hydrothermal MnO2 nanomaterials
- 21 September 2026
- Published by Elsevier in Journal of Alloys and Compounds Communications
- Vol. 12
Influence of mineralizers on the phase evolution and surface defect chemistry of hydrothermal MnO2 nanomaterials
- Open Access
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Formamidinium and Methylammonium Iodide Surface Passivation on the Structure, Optical Properties, and Photo-stability of Open-Air MAPbI 3 Perovskite Films
The effect of post-deposition surface passivation with formamidinium iodide (FAI) and methylammonium iodide (MAI) on the structure, surface chemistry, optical properties, and photo-stability of methylammonium lead iodide (MAPbI3) perovskite films processed entirely in open air (60–70% relative humidity) was investigated. Films were spin-coated on C-TiO2/MP-TiO2/ITO substrates and analysed in the same configuration used for graphite-electrode devices. X-ray diffraction confirmed tetragonal MAPbI3 (a ≈ 8.88Å, c ≈ 12.57Å) with Scherrer (110) crystallite sizes of 25.2, 26.9, and 25.1nm for the control, MAI, and FAI films, essentially unchanged across the series (dislocation density ∼1.4–1.6×1015 m−2). Scanning electron microscopy revealed mean surface grain sizes of 125, 128, and 128nm (with a broader distribution after MAI treatment) and film thicknesses of 1050, 1329, and 1064nm. Fourier-transform infrared spectroscopy showed a new ν(C=N) band at 1712 cm−1 unique to FAI and a high-frequency C–H shift to 2823 cm−1 for MAI, evidencing distinct, cation-specific surface chemical interactions, while Raman confirmed a methylammonium-libration mode emerging only after MAI treatment. Diffuse-reflectance Tauc analysis (directallowed, baseline-corrected) gave optical band gaps of 1.58, 1.55, and 1.66 eV for MAPbI3, MAPbI3+MAI, and MAPbI3+FAI, all consistent with tetragonal MAPbI3 (∼1.55–1.61 eV); rather than a bulk-gap shift, the optical signature of passivation appears as a 13nm red-shift of the photoluminescence maximum from the control to the FAI-treated film, indicating modified surface/near-surface recombination. To link these film-level changes to functional behaviour, the films were tested in a graphite electrode stack under a white-LED bench (Pin ≈ 6.1mW, 17 330 lx, A = 0.9 cm2, ≈0.07 sun, not AM1.5G); the relative response improved by ∼2.1× (MAI) and ∼3.6× (FAI) over the control, and a 16.7-h continuous-illumination stress test (100 successive J–V sweeps) showed a positive light-soaking response for both passivated films (light-soaking factor LSF = 1.75 for MAI and 1.85 for FAI; sweep-to-sweep variability ≤ 2.4%) against a flat, noisier control (LSF = 0.99, 5.2% variability). Overall, a direct same-batch comparison shows that FAI and MAI surface passivation induce distinct surface chemistries that improve the structural quality, optical signature, and operational photo-stability of open-air MAPbI3 films, providing a materials-level basis for selecting passivation chemistry in low-cost, humid-ambient fabrication.
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Formamidinium and Methylammonium Iodide Surface Passivation on the Structure, Optical Properties, and Photo-stability of Open-Air MAPbI 3 Perovskite Films
The effect of post-deposition surface passivation with formamidinium iodide (FAI) and methylammonium iodide (MAI) on the structure, surface chemistry, optical properties, and photo-stability of methylammonium lead iodide (MAPbI3) perovskite films processed entirely in open air (60–70% relative humidity) was investigated. Films were spin-coated on C-TiO2/MP-TiO2/ITO substrates and analysed in the same configuration used for graphite-electrode devices. X-ray diffraction confirmed tetragonal MAPbI3 (a ≈ 8.88Å, c ≈ 12.57Å) with Scherrer (110) crystallite sizes of 25.2, 26.9, and 25.1nm for the control, MAI, and FAI films, essentially unchanged across the series (dislocation density ∼1.4–1.6×1015 m−2). Scanning electron microscopy revealed mean surface grain sizes of 125, 128, and 128nm (with a broader distribution after MAI treatment) and film thicknesses of 1050, 1329, and 1064nm. Fourier-transform infrared spectroscopy showed a new ν(C=N) band at 1712 cm−1 unique to FAI and a high-frequency C–H shift to 2823 cm−1 for MAI, evidencing distinct, cation-specific surface chemical interactions, while Raman confirmed a methylammonium-libration mode emerging only after MAI treatment. Diffuse-reflectance Tauc analysis (directallowed, baseline-corrected) gave optical band gaps of 1.58, 1.55, and 1.66 eV for MAPbI3, MAPbI3+MAI, and MAPbI3+FAI, all consistent with tetragonal MAPbI3 (∼1.55–1.61 eV); rather than a bulk-gap shift, the optical signature of passivation appears as a 13nm red-shift of the photoluminescence maximum from the control to the FAI-treated film, indicating modified surface/near-surface recombination. To link these film-level changes to functional behaviour, the films were tested in a graphite electrode stack under a white-LED bench (Pin ≈ 6.1mW, 17 330 lx, A = 0.9 cm2, ≈0.07 sun, not AM1.5G); the relative response improved by ∼2.1× (MAI) and ∼3.6× (FAI) over the control, and a 16.7-h continuous-illumination stress test (100 successive J–V sweeps) showed a positive light-soaking response for both passivated films (light-soaking factor LSF = 1.75 for MAI and 1.85 for FAI; sweep-to-sweep variability ≤ 2.4%) against a flat, noisier control (LSF = 0.99, 5.2% variability). Overall, a direct same-batch comparison shows that FAI and MAI surface passivation induce distinct surface chemistries that improve the structural quality, optical signature, and operational photo-stability of open-air MAPbI3 films, providing a materials-level basis for selecting passivation chemistry in low-cost, humid-ambient fabrication.
- Open Access
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Mineralizers on the Phase Evolution and Surface Defect Chemistry of Hydrothermal MnO2 Nanomaterials
This study investigates the role of mineralizer selection in modulating the crystal structure and surface chemical states of manganese dioxide (MnO2) synthesized via a hydrothermal approach. Three oxidants—K2S2O8, KMnO4, and KClO3—were employed as mineralizers, yielding distinct phase evolution and defect concentrations. X-ray Diffraction (XRD) revealed that K2S2O8 and KClO3 favor the β-MnO2 (pyrolusite) phase, while KMnO4 drives a complete phase transition to α-MnO2 (hollandite), with average crystallite sizes ranging from 30.98 to 91.31 nm. High-resolution X-ray Photoelectron Spectroscopy (XPS) deconvolution demonstrated that KClO3 promotes the highest surface defect concentration (Odef/OH ∼ 36.46%) and Mn3+ fraction (∼ 32.44%), which are essential for enhancing faradaic charge storage. Cyclic Voltammetry (CV) measurements in 1 M Na2SO4 revealed that the KClO3-derived MnO2 achieves a maximum specific capacitance of 79.86 ± 9.46 F/g at 10 mV/s, retaining 28.3% of this value at 100 mV/s, significantly outperforming K2S2O8 (40.03 ± 27.43 F/g, 21.6% retention) and KMnO4 (20.77 ± 18.87 F/g, 19.9% retention). These results establish a comprehensive mineralizer–structure–property framework for defect-engineered MnO2 in advanced electrochemical energy storage.
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Mineralizers on the Phase Evolution and Surface Defect Chemistry of Hydrothermal MnO2 Nanomaterials
This study investigates the role of mineralizer selection in modulating the crystal structure and surface chemical states of manganese dioxide (MnO2) synthesized via a hydrothermal approach. Three oxidants—K2S2O8, KMnO4, and KClO3—were employed as mineralizers, yielding distinct phase evolution and defect concentrations. X-ray Diffraction (XRD) revealed that K2S2O8 and KClO3 favor the β-MnO2 (pyrolusite) phase, while KMnO4 drives a complete phase transition to α-MnO2 (hollandite), with average crystallite sizes ranging from 30.98 to 91.31 nm. High-resolution X-ray Photoelectron Spectroscopy (XPS) deconvolution demonstrated that KClO3 promotes the highest surface defect concentration (Odef/OH ∼ 36.46%) and Mn3+ fraction (∼ 32.44%), which are essential for enhancing faradaic charge storage. Cyclic Voltammetry (CV) measurements in 1 M Na2SO4 revealed that the KClO3-derived MnO2 achieves a maximum specific capacitance of 79.86 ± 9.46 F/g at 10 mV/s, retaining 28.3% of this value at 100 mV/s, significantly outperforming K2S2O8 (40.03 ± 27.43 F/g, 21.6% retention) and KMnO4 (20.77 ± 18.87 F/g, 19.9% retention). These results establish a comprehensive mineralizer–structure–property framework for defect-engineered MnO2 in advanced electrochemical energy storage.
- Open Access
- 14 July 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Mineralizers on the Phase Evolution and Surface Defect Chemistry of Hydrothermal MnO2 Nanomaterials
This study investigates the role of mineralizer selection in modulating the crystal structure and surface chemical states of manganese dioxide (MnO2) synthesized via a hydrothermal approach. Three oxidants—K2S2O8, KMnO4, and KClO3—were employed as mineralizers, yielding distinct phase evolution and defect concentrations. X-ray Diffraction (XRD) revealed that K2S2O8 and KClO3 favor the β-MnO2 (pyrolusite) phase, while KMnO4 drives a complete phase transition to α-MnO2 (hollandite), with average crystallite sizes ranging from 30.98 to 91.31 nm. High-resolution X-ray Photoelectron Spectroscopy (XPS) deconvolution demonstrated that KClO3 promotes the highest surface defect concentration (Odef/OH ∼ 36.46%) and Mn3+ fraction (∼ 32.44%), which are essential for enhancing faradaic charge storage. Cyclic Voltammetry (CV) measurements in 1 M Na2SO4 revealed that the KClO3-derived MnO2 achieves a maximum specific capacitance of 79.86 ± 9.46 F/g at 10 mV/s, retaining 28.3% of this value at 100 mV/s, significantly outperforming K2S2O8 (40.03 ± 27.43 F/g, 21.6% retention) and KMnO4 (20.77 ± 18.87 F/g, 19.9% retention). These results establish a comprehensive mineralizer–structure–property framework for defect-engineered MnO2 in advanced electrochemical energy storage.
- 14 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Mineralizers on the Phase Evolution and Surface Defect Chemistry of Hydrothermal MnO2 Nanomaterials
This study investigates the role of mineralizer selection in modulating the crystal structure and surface chemical states of manganese dioxide (MnO2) synthesized via a hydrothermal approach. Three oxidants—K2S2O8, KMnO4, and KClO3—were employed as mineralizers, yielding distinct phase evolution and defect concentrations. X-ray Diffraction (XRD) revealed that K2S2O8 and KClO3 favor the β-MnO2 (pyrolusite) phase, while KMnO4 drives a complete phase transition to α-MnO2 (hollandite), with average crystallite sizes ranging from 30.98 to 91.31 nm. High-resolution X-ray Photoelectron Spectroscopy (XPS) deconvolution demonstrated that KClO3 promotes the highest surface defect concentration (Odef/OH ∼ 36.46%) and Mn3+ fraction (∼ 32.44%), which are essential for enhancing faradaic charge storage. Cyclic Voltammetry (CV) measurements in 1 M Na2SO4 revealed that the KClO3-derived MnO2 achieves a maximum specific capacitance of 79.86 ± 9.46 F/g at 10 mV/s, retaining 28.3% of this value at 100 mV/s, significantly outperforming K2S2O8 (40.03 ± 27.43 F/g, 21.6% retention) and KMnO4 (20.77 ± 18.87 F/g, 19.9% retention). These results establish a comprehensive mineralizer–structure–property framework for defect-engineered MnO2 in advanced electrochemical energy storage.
- Open Access
- 7 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
Structural, optical, and electrical properties of Cu-doped NiO films synthesized by spray pyrolysis for potential gas sensing applications
- 7 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessStructural, optical, and electrical properties of Cu-doped NiO films synthesized by spray pyrolysis for potential gas sensing applications
- Open Access
- 17 June 2026
- Published by Elsevier in SSRN Electronic Journal
MnO2 nanorod-decorated urchin-like Nb2O5 nanospheres for electrochemical charge storage applications
In this study, MnO2 nanorod-decorated urchin-like Nb2O5 nanospheres were synthesizedvia a facile hydrothermal method to investigate their electrochemical charge storagebehavior. Structural and morphological characterizations using X-ray diffraction (XRD),field-emission scanning electron microscopy (FESEM) coupled with energy-dispersive Xrayspectroscopy (EDX), and high-resolution transmission electron microscopy (HRTEM)confirmed the formation of crystalline Nb2O5 with MnO2 nanorod decoration. Electrochemical performance evaluated by cyclic voltammetry (CV) in 1 M Na2SO4 electrolyterevealed a significant improvement in specific capacitance (at a scan rate of 10 mV/s)from 11 F/g for pristine Nb2O5 and 19 F/g for MnO2 to 94 F/g for the Nb2O5/MnO2composite. The improved performance is attributed to the synergistic effect betweenthe high pseudo-capacitance of MnO2 and the stable structure of the urchin-like Nb2O5nanospheres, which facilitates efficient charge transfer and ion diffusion. These resultsdemonstrate that MnO2 decoration can effectively enhance the electrochemical chargestorage properties of Nb2O5-based electrodes.
- 17 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMnO2 nanorod-decorated urchin-like Nb2O5 nanospheres for electrochemical charge storage applications
In this study, MnO2 nanorod-decorated urchin-like Nb2O5 nanospheres were synthesizedvia a facile hydrothermal method to investigate their electrochemical charge storagebehavior. Structural and morphological characterizations using X-ray diffraction (XRD),field-emission scanning electron microscopy (FESEM) coupled with energy-dispersive Xrayspectroscopy (EDX), and high-resolution transmission electron microscopy (HRTEM)confirmed the formation of crystalline Nb2O5 with MnO2 nanorod decoration. Electrochemical performance evaluated by cyclic voltammetry (CV) in 1 M Na2SO4 electrolyterevealed a significant improvement in specific capacitance (at a scan rate of 10 mV/s)from 11 F/g for pristine Nb2O5 and 19 F/g for MnO2 to 94 F/g for the Nb2O5/MnO2composite. The improved performance is attributed to the synergistic effect betweenthe high pseudo-capacitance of MnO2 and the stable structure of the urchin-like Nb2O5nanospheres, which facilitates efficient charge transfer and ion diffusion. These resultsdemonstrate that MnO2 decoration can effectively enhance the electrochemical chargestorage properties of Nb2O5-based electrodes.
- Open Access
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Molarity-Controlled FAI Surface Passivation for Enhanced Photovoltaic Performance of MAPbI3 Perovskite Solar Cells
In this paper, we study the effect of Formamidinium Iodide (FAI) layer with various molarities on the structural, morphological, optical, and photovoltaic properties of MAPbI3-based perovskite solar cells. FAI is used as a passivation layer of MAPbI3 perovskite, which is less thermodynamically stable. FAI has a greater number of hydrogen bonds between hydrogen ammonium cations and iodine ions in the organic framework, making the FAI structure more stable. The spin-coating method is used to deposit the solution onto the substrate surface. The addition of the FAI passivation layer is performed at molarities of 0.016, 0.032, 0.048, 0.064, and 0.080 M. As a result, the thickness of TiO2/MAPbI3/FAI layers variants increased from 907 nm (FAI 0.016) to 1594 nm (FAI 0.080). XRD analysis showed that the dislocation density and lattice strain decreased at FAI 0.032 and FAI 0.048. FTIR analysis confirmed the successful incorporation of FAI on the MAPbI3 surface, as indicated by the characteristic N-H, C-H, and C-N vibrational bands whose intensities increased with increasing FAI molarity. The bandgap decreased slightly from 1.50 eV to ~1.40 eV with increasing FAI molarity, indicating improved optical absorption associated with effective surface passivation of the MAPbI3 layer, as observed in UV-Vis and photoluminescence spectroscopy analyses. J-V measurements show that the PSC performance strongly depends on the FAI passivation molarity, with the highest power conversion efficiency obtained at FAI concentrations of 0.032 M. These results demonstrate that optimizing the FAI passivation molarity effectively improves the optical properties, reduces defect density, and enhances the photovoltaic performance of MAPbI3based perovskite solar cells.
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMolarity-Controlled FAI Surface Passivation for Enhanced Photovoltaic Performance of MAPbI3 Perovskite Solar Cells
In this paper, we study the effect of Formamidinium Iodide (FAI) layer with various molarities on the structural, morphological, optical, and photovoltaic properties of MAPbI3-based perovskite solar cells. FAI is used as a passivation layer of MAPbI3 perovskite, which is less thermodynamically stable. FAI has a greater number of hydrogen bonds between hydrogen ammonium cations and iodine ions in the organic framework, making the FAI structure more stable. The spin-coating method is used to deposit the solution onto the substrate surface. The addition of the FAI passivation layer is performed at molarities of 0.016, 0.032, 0.048, 0.064, and 0.080 M. As a result, the thickness of TiO2/MAPbI3/FAI layers variants increased from 907 nm (FAI 0.016) to 1594 nm (FAI 0.080). XRD analysis showed that the dislocation density and lattice strain decreased at FAI 0.032 and FAI 0.048. FTIR analysis confirmed the successful incorporation of FAI on the MAPbI3 surface, as indicated by the characteristic N-H, C-H, and C-N vibrational bands whose intensities increased with increasing FAI molarity. The bandgap decreased slightly from 1.50 eV to ~1.40 eV with increasing FAI molarity, indicating improved optical absorption associated with effective surface passivation of the MAPbI3 layer, as observed in UV-Vis and photoluminescence spectroscopy analyses. J-V measurements show that the PSC performance strongly depends on the FAI passivation molarity, with the highest power conversion efficiency obtained at FAI concentrations of 0.032 M. These results demonstrate that optimizing the FAI passivation molarity effectively improves the optical properties, reduces defect density, and enhances the photovoltaic performance of MAPbI3based perovskite solar cells.
- 19 February 2026
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 46 (10)
Mechanical properties of ceramics electrodes and electrolytes for solid oxide fuel cell applications: A review
- 19 February 2026
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 46 (10)
Mechanical properties of ceramics electrodes and electrolytes for solid oxide fuel cell applications: A review