MSMikael Svensson

Mikael Svensson

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mikael Svensson has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fracture toughness and shear yield stress determination from quasi-linear cutting tests of Scots pine (Pinus sylvestris L.) with a normalisation process by local density aided by X-ray computed tomography

    by Daniel Chuchala, Yunbo Huang, Kazimierz A. Orlowski, Dietrich Buck, Dawid Stenka, Magnus Fredriksson, Mikael Svensson

    The Atkins model has been widely adopted for determining mechanical properties of wood, such as fracture toughness and shear yield stress, which are typically normalised by global density for cutting force and power predictions. This study explores the feasibility of determining these mechanical properties for knotty and clear Scots pine (Pinus sylvestris L.) using local densities revealed by X-ray computed tomography scanning. Six wood workpieces, three from Poland and three from Sweden, were scanned and subsequently cut on a custom single-tooth quasi-linear cutting machine. Cutting forces for both clear and knotty regions were recorded and normalised by local densities. Results indicate that clear Polish pine exhibits higher local-density-normalised fracture toughness and shear yield stress than Swedish pine, suggesting that wood origin influences mechanical properties beyond mere density differences. Knots display significantly lower local-density-normalised shear yield stress compared to clear wood, despite their higher density. The large variation in normalised fracture toughness observed in knots is attributed to differences in cutting direction relative to knot orientation. The study highlights the effectiveness of computed tomography scanning to provide detailed insights into wood density and structure, enabling more accurate normalization of cutting forces and enhancing the understanding of wood machinability across different origins and structural characteristics.


  • Open Access

    Analysis of the relationship between cutting forces and local structural properties of Scots pine wood aided by computed tomography

    by Yunbo Huang, Daniel Chuchala, Dietrich Buck, Kazimierz A. Orlowski, Magnus Fredriksson, Mikael Svensson

    X-ray computed tomography (CT) is utilised in some sawmills today, primarily for enhancing value yield and for process automation, which includes log sorting and sawing optimisation. Nevertheless, there is a scarcity of recent research utilising CT to assess the local cutting process. As a preliminary study, this paper addresses this gap by using CT to investigate the connections between local cutting force and local wood properties including density, knots, and annual ring width. Workpieces of Scots pine (Pinus sylvestris L.), from Sweden and Poland, were CT-scanned in laboratory conditions. Quasi-linear cutting tests were then performed on both clear and knotty regions of the workpieces using a custom-made laboratory stand with a Stellite-tipped tooth mounted on piezoelectric sensors. It was found that density influences cutting forces for both clear and knotty wood, and this effect increased noticeably with increasing uncut chip thickness. Changes in wood density, such as between sapwood and heartwood or between clear wood and knot, caused dynamic changes in cutting forces and temporary disturbances to the stability of the system. Normalisation of cutting forces by local density allowed the conclusion that density is not the only property affecting cutting forces. Other structural properties, e.g. annual ring width and latewood–earlywood proportion may affect the cutting process as well, which requires deeper analysis in the future research. This preliminary study demonstrates the feasibility and usefulness of coupling CT data with cutting force measurements and suggests further research on the relationship between cutting force and wood properties.


  • Open Access

    Minor cutting edge angles of sawing teeth: effect on cutting forces in wood

    by Vanessa Meulenberg, Mats Ekevad, Mikael Svensson

    Optimising the cutting tool geometries can reduce waste while increasing timber yield. The industry is moving towards thin-kerf bandsawing of timber, and therefore, the geometry of the minor cutting edge and minor first flanks of cutting teeth become more important. Six cutting teeth with varying minor cutting edge angles ( $$0^{\circ }$$ 0 ∘ , $$2^{\circ }$$ 2 ∘ , $$4^{\circ }$$ 4 ∘ , $$6^{\circ }$$ 6 ∘ ) and minor cutting edge clearance angles ( $$2^{\circ }$$ 2 ∘ , $$4^{\circ }$$ 4 ∘ , $$6^{\circ }$$ 6 ∘ ) were tested by cutting into the heartwood and sapwood of frozen and non-frozen Norway spruce (Picea abies (L.) Karst.) and Scots pine (Pinus sylvestris L.). Single cutting tooth tests were conducted, and the cutting and feeding forces were measured. The cutting forces were higher for Scots pine due to its higher density. Frozen sapwood resulted in higher cutting forces. The feeding force of frozen sapwood stood out as it was highly negative (i.e. self-feeding) compared to frozen heartwood, non-frozen heartwood and non-frozen sapwood. An increase in the minor cutting edge angle and minor cutting edge clearance angles, and therefore more room for elastic spring-back, can lead to up to less friction and 40% lower cutting forces. Higher minor cutting edge angles and minor cutting edge clearance angles resulted in less-negative feeding forces (i.e. less self-feeding) for frozen sapwood but remained relatively unchanged for the other wood conditions.