Saul Daniel Santillan Gutierrez
Research Subjects
Saul Daniel Santillan Gutierrez has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Arturo Barba-Pingarrón
Centro de Ingeniería de Superficies y Acabados, Facultad de Ingeniería, Universidad Nacional Autónoma de México Ciudad Universitaria, Ciudad de México 04510, Mexico
2 shared publications - Benjamín Vargas-Arista
Tecnologico Nacional de Mexico, Instituto Tecnologico de Tlalnepantla
2 shared publications - Celso Eduardo Cruz-González
Centro de Ingenieria y Desarrollo Industrial
2 shared publications - Isidro Guzmán-Flores
Facultad de Sistemas, Universidad Autónoma de Coahuila, Saltillo, México
1 shared publication - Jaime Taha-Tijerina
Mechanical Engineering Department, The University of Texas Rio Grande Valley, Brownsville, TX 78520, USA
1 shared publication - Ruben Perez Mora
National Council for Science and Technology (CONACYT–CIDESI), National Center for Aeronautics Technologies (CENTA), Carretera Estatal 200, km 23, Querétaro 76265, Mexico
1 shared publication
Latest Publications
- 13 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4929-4940
Effect of curing post-treatment time on mechanical properties and stress distribution of adhesively bonded dissimilar steel-aluminum joints
- 13 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4929-4940
Effect of curing post-treatment time on mechanical properties and stress distribution of adhesively bonded dissimilar steel-aluminum joints
- Open Access
- 6 March 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (48) , 530-544
Fatigue strength evaluation and fracture behavior of joined dual phase steel/AA6061-T6 aluminum alloy
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to determine maximum shear loads, for the single lap shear testing for 5.0 mm overlap length were 2 to 3.5 times higher in comparison to the 12.7 mm overlap length specimens. The results for the strain measurement revealed that higher strain-stress were developed in the 6061-T6 aluminum alloy adherend and in all cases they were lower than the adherends yield strength. Fatigue testing was carried out at 30, 50 and 70 % of the maximum shear load, 0.1 of reversibility load ratio (R) and 30 Hz of frequency. After testing, Basquin and Wholer graphs were built for each adhesive at 12.7 and 50.0 mm of overlap length. The results suggested that at higher overlapping, the cyclic maximum load increased. Additionally, the maximum fatigue loading at 10^6 cycles for MP55420 adhesive was 1.3 kN for an overlapping of 12.7 mm and 2.9 kN for 50 mm. For DC80 adhesive was 1.75 kN for overlapping 12.7 mm and 4.8 kN for 50 mm. Finally, for the Betamate 120 adhesive was 1.8 kN for 12.7 mm of overlapping and 6 kN for 50 mm. The post-fracture visual inspection revealed that MP55420 and Betamate 120 adhesives had a cohesive failure, while the DC-80 showed cohesive-adhesive failure. Additionally, the scanning electron microscopy evaluation on the spew fillet revealed resolved striations and a network of small micro-dimples for the Betamate 120 and MP55420 adhesives. On the other hand, DC-80 adhesive exhibited notable facet fragile failure that was confirmed by the shape of stress-strain plot with straight line from the origin to the point of fracture.
- 6 March 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (48) , 530-544
Open AccessFatigue strength evaluation and fracture behavior of joined dual phase steel/AA6061-T6 aluminum alloy
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to determine maximum shear loads, for the single lap shear testing for 5.0 mm overlap length were 2 to 3.5 times higher in comparison to the 12.7 mm overlap length specimens. The results for the strain measurement revealed that higher strain-stress were developed in the 6061-T6 aluminum alloy adherend and in all cases they were lower than the adherends yield strength. Fatigue testing was carried out at 30, 50 and 70 % of the maximum shear load, 0.1 of reversibility load ratio (R) and 30 Hz of frequency. After testing, Basquin and Wholer graphs were built for each adhesive at 12.7 and 50.0 mm of overlap length. The results suggested that at higher overlapping, the cyclic maximum load increased. Additionally, the maximum fatigue loading at 10^6 cycles for MP55420 adhesive was 1.3 kN for an overlapping of 12.7 mm and 2.9 kN for 50 mm. For DC80 adhesive was 1.75 kN for overlapping 12.7 mm and 4.8 kN for 50 mm. Finally, for the Betamate 120 adhesive was 1.8 kN for 12.7 mm of overlapping and 6 kN for 50 mm. The post-fracture visual inspection revealed that MP55420 and Betamate 120 adhesives had a cohesive failure, while the DC-80 showed cohesive-adhesive failure. Additionally, the scanning electron microscopy evaluation on the spew fillet revealed resolved striations and a network of small micro-dimples for the Betamate 120 and MP55420 adhesives. On the other hand, DC-80 adhesive exhibited notable facet fragile failure that was confirmed by the shape of stress-strain plot with straight line from the origin to the point of fracture.