Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yangfeng Wu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:

  • Jinsheng Jia

    State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China

    8 shared publications
  • Cuiying Zheng

    State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China

    5 shared publications
  • Baozhen Jia

    State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China

    4 shared publications
  • Lei Zhao

    Huadian Electric Power Research Institute Co., Ltd., XiYuan, Road 1-10, Xihu District, Hangzhou 310030, China

    3 shared publications
  • Wambley Adomako Baah

    State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China

    3 shared publications
  • Lei Zhao

    State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China

    2 shared publications

Latest Publications

  • Open Access

    Numerical and Fracture Mechanical Evaluation of Safety Monitoring Indexes and Crack Resistance in High RCC Gravity Dams Under Hydraulic Fracture Risk

    by Mohamed Ramadan, Jinsheng Jia, Lei Zhao, Xu Li, Yangfeng Wu

    High concrete gravity dams, particularly Roller-Compacted Concrete (RCC) types, face long-term safety challenges due to weak interlayer formation and crack propagation. This study presented a comprehensive evaluation of safety monitoring indexes for the Guxian high RCC dam (currently under construction) using both numerical and mathematical models. A finite element method (FEM) is employed with a strength reduction approach to assess dam stability considering weak layers. In parallel, a fracture mechanical model is used to investigate the safety of the Guxian dam based on failure assessment diagrams (FADs) for calculating the safety factor and the residual strength curve for calculating critical crack depth for two different crack locations, single-edge and center-through crack, to investigate the high possible risk associated with crack location on the dam safety. Additionally, the Guxian dam’s resistance to hydraulic fracture is assessed under two fracture mechanic failure modes, Mode I (open type) and Mode II (in-plane shear), by computing the ultimate overload coefficient using a proposed novel derived formula. The results show that weak layers reduce the dam’s safety index by approximately 20%, especially in lower sections with extensive interfaces. Single-edge cracks pose greater risk, decreasing the safety factor by 10% and reducing critical crack depth by 40% compared to center cracks. Mode II demonstrates higher resistance to hydraulic fracture due to greater shear strength and fracture energy, whereas Mode I represents the most critical failure scenario. The findings highlight the urgent need to incorporate weak layer behavior and hydraulic fracture mechanisms into dam safety monitoring, and to design regulations for high RCC gravity dams.


  • Open Access

    Enhancement of Air-Entrained Grout-Enriched Vibrated Cemented Sand, Gravel and Rock (GECSGR) for Improving Frost and Thawing Resistance in CSGR Dams

    by Wambley Adomako Baah, Jinsheng Jia, Cuiying Zheng, Baozhen Jia, Yue Wang, Yangfeng Wu

    Cemented Sand, Gravel, and Rock (CSGR) dams have traditionally used either Conventional Vibrated Concrete (CVC) or Grout-Enriched Roller Compacted Concrete (GERCC) for protective and seepage control layers in low- to medium-height dams. However, these methods are complex, prone to interference, and uneconomical due to significant differences in the expansion coefficient, elastic modulus, and hydration heat parameters among CSGR, CVC, and GERCC. This complexity complicates quality control during construction, leading to the development of Grout-Enriched Vibrated Cemented Sand, Gravel, and Rock (GECSGR) as an alternative. Despite its potential, GECSGR has limited use due to concerns about freeze–thaw resistance. This project addresses these concerns by developing an air-entrained GECSGR grout formulation and construction technique. The study follows a five-phase approach: mix proportioning of C1806 CSGR; optimization of the grout formulation; determination of grout addition rate; evaluation of small-scale lab samples of GECSGR; and field application. The results indicate that combining 8–12% of 223 kg/m3 cement grout with 2–2.23 kg/m3 of admixtures, mud content of 15%, a marsh time of 26–31 s. and a water/cement ratio of 0.5–0.6 with the C1806 parent CSGR mixture achieved a post-vibration in situ air content of 4–6%, excellent freeze–thaw resistance (F300: mass loss −10 m/s). The development of a 2-in-1 slurry addition and vibration equipment eliminated performance risks and enhanced efficiency in field applications, such as the conversion of the C1804 CSGR mixture into air-entrained GECSGR grade C9015W6F50 for the 2.76 km Qianwei protection dam. Economic analysis revealed that the unit cost of GECSGR production is 18.3% and 6.33% less than CVC and GERCC, respectively, marking a significant advancement in sustainable cement-based composite materials in the dam industry.


  • Open Access

    Optimizing Paste and Mortar Margins (α and β) to Enhance Compressive Strength in Cemented Sand, Gravel and Rock

    by Wambley Adomako Baah, Jinsheng Jia, Cuiying Zheng, Yue Wang, Baozhen Jia, Yangfeng Wu

    A suitable range of paste and mortar margins (α and β) to enhance compressive strength in Rich-Mix cemented sand gravel and rock (CSGR) material for application in CSGRD construction is critical. SL 678-2014 recommends margins > 1, which are specifically designed to fill the voids within the fine and coarse aggregates with paste and mortar, respectively, while allowing some excess for workability. However, the optimum ranges of values after 1 are inadequately determined, often leading to high efforts and time-consuming trial mixes that are not economical. This study evaluates two datasets to identify the optimal ranges of α and β margins for compressive strength development in Rich-Mix CSGR, aiming to achieve the compressive strength class C18020, intended for use as cushion, protective, and seepage control layers in CSGRD. Using Pearson correlations, t-statistics, and p-values, the first dataset (7, 28, 90, and 180 days) showed weak correlations between paste margins and compressive strengths (coefficients 0.172 to 0.418, p-values > 0.05) and negligible relationships for mortar margins (coefficients −0.269 to 0.204, p-values > 0.05), affirming the contribution of other factors in the compressive strength development in CSGR. The second dataset (14, 28, 90, and 180 days) revealed significant positive correlations between paste margins and strengths at 14, 90, and 180 days (coefficients up to 0.850, p-values < 0.05). Mortar margins, however, negatively impacted strength (coefficients −0.544 to −0.628, p-values < 0.05), revealing the need to control the sand ratio. The optimal range of values was 1.05 ≤ α ≤ 1.09 and 1.15 ≤ β ≤ 1.25, with a water–binder ratio of 0.7~1.3, vibrating–compacted value (VC) of 2~8 s, and sand ratio of 18~35%. These findings highlight the significance of precise paste and mortar margin ranges in the compressive strength development of Rich-Mix CSGR.


  • Open Access

    Comprehensive Safety Analysis of Ultimate Bearing Capacity Considering Hydraulic Fracture for Guxian High RCC Gravity Dam

    by Mohamed Ramadan, Jinsheng Jia, Lei Zhao, Xu Li, Yangfeng Wu

    The widespread adoption of high concrete gravity dams in China and globally underscores the necessity for enhancing design processes to address potential risks, notably hydraulic fracture. This study delves into this urgency by scrutinizing common design regulations and investigating the impact of hydraulic fracture on high concrete gravity dams. A comparative analysis of design specifications from China, the USA, and Switzerland, employing the gravity method, elucidates distinctions, focusing on the Guxian dam. In addition, evaluation of standards with higher resistance to hydraulic fracture was conducted using the Finite Element Method (FEM) with XFEM (eXtended Finite Element Method), employing initial cracks with different depths at the dam heel ranging from 0.2 to 2 m. The vulnerability of the Guxian dam’s cross-section to safety risks prompts further inquiry into the dam’s resistance to hydraulic fracture. Therefore, high-pressure water splitting risks to the ultimate bearing capacity were examined through FEM simulation and theoretical calculations. FEM simulations assessed the dam’s ultimate bearing capacity with and without automatic crack propagation combining the XFEM and overloading methods, particularly considering weak layers in the RCC (Roller-Compacted Concrete) dams. Theoretical calculations utilized a fracture mechanical evaluation model. This model derived mechanism formulas to assess the dam’s resistance to hydraulic fracture. Additionally, the investigation explored the effect of the uplift pressure on the ultimate overload coefficient. Findings indicated that the Guxian dam’s current cross-sectional area was insufficiently safe against hydraulic fracture, necessitating an increase to its cross-sectional area to 18,888.1 m2. Notably, the USA’s and Switzerland’s criteria exhibited greater resistance to hydraulic fracture than the Chinese criteria, especially without considering uplift pressure. Also, the Chinese regulations tended to calculate a lower dam cross-sectional area compared with the other regulations. Numerical calculations revealed a substantial decrease in overall dam safety (up to 48%) when considering automatic crack propagation and the dam’s weak layers. The fracture mechanical evaluation model showed that the Guxian dam had the lowest resistance, with an overloading coefficient of 1.05 considering the uplift pressure. In the case of not considering the uplift pressure, the dam resistance to hydraulic fracture increased and the overloading coefficient rose to 1.27. The results highlighted the risk of hydraulic fracture in concrete dams. Hence, it is recommended that design specifications of high concrete gravity dams incorporate safety analyses of hydraulic fracture in the design process. Reducing uplift pressure plays a crucial role in enhancing the dam’s resistance to hydraulic fractures, emphasizing the need for this consideration in safety evaluations. The differences between the three design specifications were particularly pronounced for dams higher than 200 m. In contrast, dams of 50 m yielded similar results across these regulations.


  • Open Access

    A New Method for Constructing the Protection and Seepage Control Layer for CSGR Dam and Its Application

    by Yangfeng Wu, Jinsheng Jia, Cuiying Zheng, Baozhen Jia, Yang Wang, Wambley Adomako Baah

    Effective seepage control is crucial for maintaining the structural integrity of Cemented Sand, Gravel and Rock (CSGR) dams. Traditional methods using conventional concrete (CVC) or grout-enriched roller-compacted concrete (GERCC) are costly and disruptive. This paper presents a novel technique for constructing the protection and seepage control layer in Cemented Sand, Gravel and Rock (CSGR) dams. The method involves grouting and vibrating the loosened Cemented Sand, Gravel and Rock (CSGR) material to create vibrated grout-enriched Cemented Sand, Gravel and Rock, which performs similarly to concrete. A new surface water stop structure has also been developed for the structural joints. Laboratory tests revealed that Cemented Sand, Gravel and Rock (CSGR) with a vibrating–compacted (VC) value of 2–6 s and a compressive strength of 4 MPa meets design requirements for medium and low dams when the slurry addition rate is 8–12%. The T-shaped surface water stop demonstrated a bonding strength of over 1.8 MPa, withstanding a water pressure of 1.6 MPa. This method, integrated with dam body construction, reduces material costs by about 50% and eliminates construction interference. Specialized equipment for this technique has been developed, with a capacity of 12 m2/h. Implemented in the Minjiang Navigation and Hydropower Qianwei Project and Shaping I Hydropower Station, it has shown significant economic, environmental and safety benefits, promoting sustainable dam construction.


  • Open Access

    Investigation on Hydraulic Fracturing and Flexible Anti-Hydrofracturing Solution for Xiaowan Arch Dam

    by Yangfeng Wu, Jinsheng Jia, Yang Wang, Cuiying Zheng, Lei Zhao, Baozhen Jia

    Understanding hydraulic fracturing in concrete super-high arch dams is vital for the implementation of safety measures on the bearing surface. In this study, we conducted tests on hydraulic fracturing for the Xiaowan arch dam (294.5 m) to analyze concrete behavior at cracks under various stress conditions. The risk of hydraulic fracturing near the dam heel was identified without compressive stress. Addressing this, we propose a flexible anti-hydrofracturing system using GB sealing material and a spray polyurea coating. Simulation tests on three schemes: ‘3 mm GB plate + 4 mm polyurea’, ‘1 mm GB glue + 5 mm polyurea’, and ‘7 mm polyurea’ showed effective prevention of hydrofracturing at concrete crack openings of 5 mm, 8 mm, or 10 mm under 300 m water pressure. Field tests supported ‘3 mm GB plate + 4 mm polyurea’ and ‘7 mm polyurea’ as optimal solutions for dam sections. Implementation involves a protective block layout with ‘3 mm GB plate + 4 mm polyurea’ on blocks and ‘7 mm polyurea’ in interval zones and corners. Since 2008, maximum leakage, including rock foundation, has remained minimal at 2.78 L/s under regular water levels. These insights aid similar concrete dams in optimizing safety systems.


  • Open Access

    Research and Application of Key Technologies for the Construction of Cemented Material Dam with Soft Rock

    by Jinsheng Jia, Lianying Ding, Yangfeng Wu, Chun Zhao, Lei Zhao

    In order to safely and efficiently use soft rock aggregate cemented dams in red bed regions and promote the development of widely sourced cemented sand and gravel dam materials, the Jinjigou project in China applied soft rock for the first time in the construction of cemented material dams. This article further explores the concept of cemented material dams from conducting on-site direct shear tests and research on soft rock material ratios and explores and invents a new structure and construction method by combining soft rock cemented sand and gravel with cemented rockfill. This article also proposes a digital mixing and intelligent dynamic control method for cemented material dams with soft rock. The research results show that soft rock aggregate content not exceeding 60% can produce soft rock cemented gravel with a compressive strength of no less than 6 MPa. The stress on the dam body is small and does not produce tensile stress. The dam body with added soft rock has certain shear-bearing capacity, with a shear friction coefficient of 0.99~1.10 MPa, cohesion of 0.26~0.53 MPa, and high residual strength, accounting for 60~80% of the peak strength. At the same time, the problems of large fluctuations in moisture content and the uneven grading of the soft rock and riverbed gravel mix during the mixing and production process, and the significant influence on safety caused by the large strength dispersion of the cemented sand and gravel, are resolved, ensuring the quality of soft rock cemented sand and gravel preparation. The successful application of soft rock cemented material dams in Jinjigou has achieved a breakthrough in key technologies for soft rock cemented dam construction in red bed regions, proving the feasibility of soft rock cemented material dam construction and having broad prospects for application and promotion.


  • Open Access

    The Bearing Capacity of Dam Body Structure with Cemented and Weathered Materials: A Constitutive Model

    by Lei Zhao, Jinsheng Jia, Cuiying Zheng, Yangfeng Wu

    The Cemented Sand, Gravel, and Rock (CSGR) dam of Xijiang is the world’s first dam to use weathered material. As mechanical tests have shown significant low-strength and nonlinear characteristics in the constitutive curve of CSGR with weathered materials, a more rigorous approach is required in calculation and analysis. Based on the project, a constitutive model of CSGR with weathered material is constructed in the research. Then, the bearing capacity of the dam is studied by using the strength-reduction method and the overload method on the basis of the constitutive model. In order to further obtain the real bearing capacity of the dam, this paper also considers the hydraulic fracturing factor and analyzes its influence at the same time. Conclusions drawn are then applied to the Xijiang project, where the effect is promising.