Pedro Henrique Alves Corrêa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pedro Henrique Alves Corrêa has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Auteliano Antunes Santos
DSI/FEM, Universidade Estadual de Campinas (UNICAMP), Rua Mendeleyev, 200, Campinas, São Paulo, Brazil
4 shared publications - Matteo Magelli
Politecnico di Torino
2 shared publications - Paola Gonzalez Ramos
Railway Laboratory (Lafer), University of Campinas (UNICAMP), Cidade Universitária, Campinas, Brazil
2 shared publications - Guilherme Fabiano Mendonça dos Santos
Universidade Federal do Espírito Santo - Departamento de Engenharia Mecânica
1 shared publication - Luis Henrique DA Silva Teixeira
Railway Laboratory (Lafer), University of Campinas (UNICAMP), Cidade Universitária, Campinas, Brazil
1 shared publication - Matheus Valente Lopes
University of Campinas (Unicamp
1 shared publication
Latest Publications
- 17 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-Body Dynamics
Assessing the effect of modelling approaches for longitudinal train dynamics simulations with a multibody code
Different methods can be used to incorporate longitudinal train dynamics into multibody models, which is crucial for understanding the dynamic behaviour of railway vehicles. The main contribution of the article is to test and compare different strategies under the same simulation scenario, involving a group of four wagons with three-piece bogies. Some strategies are based on data exchange between multibody and longitudinal train dynamics frameworks, while others are purely standalone multibody models, including longitudinal train dynamics states. The study confirms that all strategies can yield similar results, but they differ significantly in computational efficiency. Modelling vehicles as masses with a single degree of freedom within the multibody environment is 6.5 times slower than running a multibody simulation with in-train forces from a preliminary longitudinal train dynamics simulation. On the other hand, co-simulation performs poorly, mainly due to the chosen communication rate between longitudinal train dynamics and multibody codes. When an optimal data exchange rate is selected, computational speeds can decrease by about three orders of magnitude in the reference scenario. A balanced solution can be achieved by modelling wagon sets with large masses inside the multibody framework, reducing the number of degrees of freedom and thus achieving computational speeds comparable to those of the straightforward methods.
- 17 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-Body Dynamics
Assessing the effect of modelling approaches for longitudinal train dynamics simulations with a multibody code
Different methods can be used to incorporate longitudinal train dynamics into multibody models, which is crucial for understanding the dynamic behaviour of railway vehicles. The main contribution of the article is to test and compare different strategies under the same simulation scenario, involving a group of four wagons with three-piece bogies. Some strategies are based on data exchange between multibody and longitudinal train dynamics frameworks, while others are purely standalone multibody models, including longitudinal train dynamics states. The study confirms that all strategies can yield similar results, but they differ significantly in computational efficiency. Modelling vehicles as masses with a single degree of freedom within the multibody environment is 6.5 times slower than running a multibody simulation with in-train forces from a preliminary longitudinal train dynamics simulation. On the other hand, co-simulation performs poorly, mainly due to the chosen communication rate between longitudinal train dynamics and multibody codes. When an optimal data exchange rate is selected, computational speeds can decrease by about three orders of magnitude in the reference scenario. A balanced solution can be achieved by modelling wagon sets with large masses inside the multibody framework, reducing the number of degrees of freedom and thus achieving computational speeds comparable to those of the straightforward methods.
- 14 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 431-442
Algorithm-based strategy to define an equivalent railway track for wear simulations
Multibody simulations of train dynamics commonly employ generic short tracks to validate and observe the behaviour of wagons in certain conditions. However, for proper wheel wear analysis, the entire railway track should be modelled, increasing computational cost and time to obtain worn profiles and wear parameters. The major novelty of this work is the description of a reproducible algorithm-based methodology to obtain a statistically representative shorter equivalent railway track for wear simulations. The proposed methodology includes combining a real measured track with multibody dynamic simulation. To verify the approach, a case study was conducted on a 505 km-long railway in Brazil. Additionally, two distinct vehicles were employed: a European wagon with a standard gauge and a Brazilian wagon with a meter gauge. The shorter equivalent tracks were compared in terms of worn area and wear depth to the initial track, and the generated tracks were cross-compared between vehicles to verify the robustness of the method. It is observed that wear simulations can be performed more efficiently and effectively, reducing the computational time by at least 94%, while still obtaining accurate results, given that the final equivalent tracks were 18.59 times shorter for the Brazilian model and 22.45 times shorter for the European model comparing to the real track, with the maximum deviation being 6.55% in flange depth and with a maximum root mean-square error (RMSE) of 871 nm.
- 14 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 431-442
Algorithm-based strategy to define an equivalent railway track for wear simulations
Multibody simulations of train dynamics commonly employ generic short tracks to validate and observe the behaviour of wagons in certain conditions. However, for proper wheel wear analysis, the entire railway track should be modelled, increasing computational cost and time to obtain worn profiles and wear parameters. The major novelty of this work is the description of a reproducible algorithm-based methodology to obtain a statistically representative shorter equivalent railway track for wear simulations. The proposed methodology includes combining a real measured track with multibody dynamic simulation. To verify the approach, a case study was conducted on a 505 km-long railway in Brazil. Additionally, two distinct vehicles were employed: a European wagon with a standard gauge and a Brazilian wagon with a meter gauge. The shorter equivalent tracks were compared in terms of worn area and wear depth to the initial track, and the generated tracks were cross-compared between vehicles to verify the robustness of the method. It is observed that wear simulations can be performed more efficiently and effectively, reducing the computational time by at least 94%, while still obtaining accurate results, given that the final equivalent tracks were 18.59 times shorter for the Brazilian model and 22.45 times shorter for the European model comparing to the real track, with the maximum deviation being 6.55% in flange depth and with a maximum root mean-square error (RMSE) of 871 nm.
- 29 August 2022
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 61 (9) , 2456-2471
Dynamic simulation of a heavy-haul freight car under abnormal braking application on tangent and curve
Couples of heavy-haul freight cars are simulated, using a 62-degree-of-freedom multi-body model developed on Simpack®, running on both tangent track and circular curve under different conditions. A benchmark simulation running at a speed of 70 km/h is set up, and then, different breaking scenarios with 2.5 kN, 5 kN, 7.5 kN and 10 kN of abnormal braking force application are simulated. In this paper, the effect of forces acting on the wheel–rail interface is compared using the derailment coefficient (L/V) and the material wear, defined by energy dissipation (Tγ). For the double-wagon setup placed in various positions along the train, the simulations run under no braking and abnormal braking conditions, where the braking force acts in only one of the wheels of the wheelset. This condition leads to an increase of up to 18% in L/V in one curve and up to 17% of reduction on the curve in the other direction. The wear increases 68% and decreases 71%, depending on the direction of the curve. These effects haven't been associated with longitudinal dynamic effects in previous studies, including in-car shocks and traction forces.
- 29 August 2022
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 61 (9) , 2456-2471
Dynamic simulation of a heavy-haul freight car under abnormal braking application on tangent and curve
Couples of heavy-haul freight cars are simulated, using a 62-degree-of-freedom multi-body model developed on Simpack®, running on both tangent track and circular curve under different conditions. A benchmark simulation running at a speed of 70 km/h is set up, and then, different breaking scenarios with 2.5 kN, 5 kN, 7.5 kN and 10 kN of abnormal braking force application are simulated. In this paper, the effect of forces acting on the wheel–rail interface is compared using the derailment coefficient (L/V) and the material wear, defined by energy dissipation (Tγ). For the double-wagon setup placed in various positions along the train, the simulations run under no braking and abnormal braking conditions, where the braking force acts in only one of the wheels of the wheelset. This condition leads to an increase of up to 18% in L/V in one curve and up to 17% of reduction on the curve in the other direction. The wear increases 68% and decreases 71%, depending on the direction of the curve. These effects haven't been associated with longitudinal dynamic effects in previous studies, including in-car shocks and traction forces.