Hugo Laffolley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hugo Laffolley has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Bernd Grambow
2 shared publications- Christophe Journeau
CEA, DES, IRESNE, DTN, Severe Accident Experimental Laboratory
2 shared publications Christophe Suteau
2 shared publications- Jules Delacroix
CEA, DES, IRESNE, DTN, SMTA, Severe Accident Experimental Laboratory, Cadarache, Saint-Paul-Lez-Durance, France
2 shared publications Sarah Thilliez
2 shared publications- Youichi Tsubota
Japan Atomic Energy Agency 2-4 Shirakata Naka-Gun
2 shared publications
Latest Publications
- Open Access
- 19 July 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (30) , 45423-45438
Development of a 3D-Printed Two-Stage Virtual Impactor for Radioactive Aerosol Size Classification and Direct Analysis
Radioactive aerosol size classification is important for exposure assessment and decommissioning operations, particularly at the Fukushima Daiichi Nuclear Power Plant decommissioning site, where airborne particles may be generated or resuspended during remote inspection and debris retrieval. This study presents the development of a two-stage 3D-printed virtual impactor, called μSPLIT, designed to separate aerosols into three aerodynamic diameter classes (>10 μm, 1–10 μm, and <1 μm) while enabling direct postcollection analysis on integrated filters. The objective is to develop a virtual impactor that can be fabricated at a reduced cost and be disposed of easily after usage by incineration, without generating any hazardous human exposure during cleaning and decontamination activities, and free from metallic wastes that are not easily disposed of. The flow path was designed and optimized by computational fluid dynamics and Lagrangian particle tracking, and prototypes were fabricated by stereolithography. Numerical simulations predicted cutoff diameters of 9.0 and 1.3 μm for the first and second stages, respectively, with relatively sharp separation in both cases. The simulations also identified limitations of the current geometry, including small-particle contamination in the minor flow and large-particle contamination in the major flow of the second stage. Dimensional measurements of printed prototypes revealed contraction and corner rounding in the internal channels, confirming the need for fabrication compensation and quality control. Experimental tests with incense smoke provided a preliminary functional check, showing that submicrometric particles were mostly collected in the <1 μm particle class. Additional tests with Rn-progeny-bearing NaCl particles, characterized by a geometric mean aerodynamic diameter of 1.70 μm, produced the highest α activity on the middle filter (1–10 μm particle class), consistent with the expected classification. These results demonstrate the proof of concept of a lightweight and low-cost impactor for simultaneous aerosol size classification and direct radioactive particle analysis, while also identifying key areas requiring further optimization, particularly the second-stage geometry, quantitative wall loss assessment, and validation with standardized aerosols.
- 19 July 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (30) , 45423-45438
Open AccessDevelopment of a 3D-Printed Two-Stage Virtual Impactor for Radioactive Aerosol Size Classification and Direct Analysis
Radioactive aerosol size classification is important for exposure assessment and decommissioning operations, particularly at the Fukushima Daiichi Nuclear Power Plant decommissioning site, where airborne particles may be generated or resuspended during remote inspection and debris retrieval. This study presents the development of a two-stage 3D-printed virtual impactor, called μSPLIT, designed to separate aerosols into three aerodynamic diameter classes (>10 μm, 1–10 μm, and <1 μm) while enabling direct postcollection analysis on integrated filters. The objective is to develop a virtual impactor that can be fabricated at a reduced cost and be disposed of easily after usage by incineration, without generating any hazardous human exposure during cleaning and decontamination activities, and free from metallic wastes that are not easily disposed of. The flow path was designed and optimized by computational fluid dynamics and Lagrangian particle tracking, and prototypes were fabricated by stereolithography. Numerical simulations predicted cutoff diameters of 9.0 and 1.3 μm for the first and second stages, respectively, with relatively sharp separation in both cases. The simulations also identified limitations of the current geometry, including small-particle contamination in the minor flow and large-particle contamination in the major flow of the second stage. Dimensional measurements of printed prototypes revealed contraction and corner rounding in the internal channels, confirming the need for fabrication compensation and quality control. Experimental tests with incense smoke provided a preliminary functional check, showing that submicrometric particles were mostly collected in the <1 μm particle class. Additional tests with Rn-progeny-bearing NaCl particles, characterized by a geometric mean aerodynamic diameter of 1.70 μm, produced the highest α activity on the middle filter (1–10 μm particle class), consistent with the expected classification. These results demonstrate the proof of concept of a lightweight and low-cost impactor for simultaneous aerosol size classification and direct radioactive particle analysis, while also identifying key areas requiring further optimization, particularly the second-stage geometry, quantitative wall loss assessment, and validation with standardized aerosols.
- 24 February 2023
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 186
Thermodynamics of aerosols during a molten core-concrete interaction at Fukushima Daiichi Unit 2 estimated conditions
- 24 February 2023
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 186
Thermodynamics of aerosols during a molten core-concrete interaction at Fukushima Daiichi Unit 2 estimated conditions
- Open Access
- 16 September 2022
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 33
Synthesis of Fukushima Daiichi Cs-bearing microparticles through molten core-concrete interaction in nitrogen atmosphere
- 16 September 2022
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 33
Open AccessSynthesis of Fukushima Daiichi Cs-bearing microparticles through molten core-concrete interaction in nitrogen atmosphere
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D