Dmitry S. Kiselev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Dmitry S. Kiselev has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Marina. G. Persova
Novosibirsk State Technical University, Novosibirsk, Russia
5 shared publications - Yulia I. Koshkina
Novosibirsk State Technical University
4 shared publications - Yuri G. Soloveichik
Novosibirsk State Technical University
4 shared publications - Anastasia P. Sivenkova
Novosibirsk State Technical University
3 shared publications - Denis V. Vagin
Novosibirsk State Technical University, Novosibirsk, Russia
3 shared publications - A. A. Mokrushin
Information and Methodological Center for Expertise, Accounting and Analysis of the Circulation of Medicinal Products, Branch of the city of Rostov-on-Don
1 shared publication
Latest Publications
- 4 October 2022
- Published by Elsevier in Computers & Geosciences
- Vol. 169
Iterative solver with folded preconditioner for finite element simulation of magnetotelluric fields
- 4 October 2022
- Published by Elsevier in Computers & Geosciences
- Vol. 169
Iterative solver with folded preconditioner for finite element simulation of magnetotelluric fields
- 1 January 2021
- Published by EAGE Publications bv
- Vol. 2021 (1) , 1-6
Analysis of the polymer flooding efficiency in one of the high-viscosity oil fields based on mathematical modeling
- 1 January 2021
- Published by EAGE Publications bv
- Vol. 2021 (1) , 1-6
Analysis of the polymer flooding efficiency in one of the high-viscosity oil fields based on mathematical modeling
- Open Access
- 1 December 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1683 (3) , 032042
Protective Coating of Irradiation Device for Fast-Neutron Reactor
The objective of this paper is to select a coating on the surface of zirconium hydride (ZH) in order to reduce hydrogen losses under the operating conditions of an irradiation device of FN-reactors. Tests were carried out on the samples of the moderator units made of zirconium hydride. Oxide, phosphide-oxide and oxide-enamel coatings were considered as a protective layer. Hydrogen yield out of the ZH was studied using a calorimeter and a mass spectrometer by thermal heating of the samples according to the test program (heating rate of 10 °C/min, maximum temperature of 1000 °C, isothermal exposure of 40 min, cooling with a furnace). The hydrogen content in the samples was determined by high temperature vacuum extraction. It is shown the oxide coating is the most technologically advanced and effective. A thermogravimetric analysis of the ZH sample with the protective oxide coating was carried out, and the temperature-time dependence of a stoichiometric coefficient (H / Zr) was determined. The amount of the hydrogen released was determined in a temperature range of 20–1100 °C. The temperature increase in up to 1100 °C leads to almost total loss of hydrogen (98–99 %). In this case, the sample retained its integrity, and the coating exfoliated and fragmented.
- 1 December 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1683 (3) , 032042
Open AccessProtective Coating of Irradiation Device for Fast-Neutron Reactor
The objective of this paper is to select a coating on the surface of zirconium hydride (ZH) in order to reduce hydrogen losses under the operating conditions of an irradiation device of FN-reactors. Tests were carried out on the samples of the moderator units made of zirconium hydride. Oxide, phosphide-oxide and oxide-enamel coatings were considered as a protective layer. Hydrogen yield out of the ZH was studied using a calorimeter and a mass spectrometer by thermal heating of the samples according to the test program (heating rate of 10 °C/min, maximum temperature of 1000 °C, isothermal exposure of 40 min, cooling with a furnace). The hydrogen content in the samples was determined by high temperature vacuum extraction. It is shown the oxide coating is the most technologically advanced and effective. A thermogravimetric analysis of the ZH sample with the protective oxide coating was carried out, and the temperature-time dependence of a stoichiometric coefficient (H / Zr) was determined. The amount of the hydrogen released was determined in a temperature range of 20–1100 °C. The temperature increase in up to 1100 °C leads to almost total loss of hydrogen (98–99 %). In this case, the sample retained its integrity, and the coating exfoliated and fragmented.
- 1 January 2020
- Published by EAGE Publications bv
- Vol. 2020 (1) , 1-8
An Approach to the Geometric 3D Inversion of Airborne EM Data for Detection and Geometrization of Local targets Overlapped by Laterally Inhomogeneous Layers
- 1 January 2020
- Published by EAGE Publications bv
- Vol. 2020 (1) , 1-8
An Approach to the Geometric 3D Inversion of Airborne EM Data for Detection and Geometrization of Local targets Overlapped by Laterally Inhomogeneous Layers
- 1 January 2020
- Published by EAGE Publications bv
- Vol. 2020 (1) , 1-6
The Approaches to Geometric EM 3-D Inversion with Consideration for IP Effect in Survey with Electric Lines
- 1 January 2020
- Published by EAGE Publications bv
- Vol. 2020 (1) , 1-6
The Approaches to Geometric EM 3-D Inversion with Consideration for IP Effect in Survey with Electric Lines