Gerard Aliana-Cervera
Gerard Aliana-Cervera has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Chiara Pasquino
4 shared publications- Alexander J. G. Lunt
Department of Mechanical Engineering, University of Bath, Bath BA2 7AY, UK
3 shared publications - Davide Mattia
Department of Chemical Engineering, University of Bath, Claverton Down, Bath BA2 7AY, United Kingdom
2 shared publications Raymond Veness
2 shared publications- Raymond Veness
Beam Instrumentation (BI), European Organization for Nuclear Research (CERN) 1 , Esplanade des Particules 1, 1217 Geneva
2 shared publications Yasemin Askar
2 shared publications
Latest Publications
- Open Access
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Radiation tolerance of carbon nanotube wires: role of chemical treatment and wire structure
Carbon nanotube (CNT) wires are increasingly used in environments that experience intense radiation, yet their behaviour under energetic proton exposure remains insufficiently understood. This work compares treated and untreated wires of diameters 11, 19 and 50 micrometres irradiated at the CERN High Radiation to Materials facility with fluences between 1.2 × 1016 and 4.0 × 1016 protons per square centimetre.Treatment through nitric acid purification followed by controlled twisting and low temperature annealing increased carbon purity to 94–97 atomic percent and reduced aluminium and silicon contamination. All wires showed increased lattice disorder after treatment, with rising AD/AG ratios and G band broadening consistent with reduced graphitic coherence length. Smaller wires accommodated irradiation through distributed bundle sliding, exhibiting moderate expansion of 10–20% and preserved geometry. Larger wires exceeded the threshold for collective bundle slip, developing swelling of up to 40% with pronounced filament relaxation. Treatment stabilised the thinnest wires but intensified deformation in the thickest by raising internal stored strain energy. Iron associated with catalyst residues concentrated locally by nearly 50% after irradiation, consistent with thermally activated diffusion toward defect trapping sites.Radiation tolerance emerges from the coupling between lattice-level defect generation, mesoscale bundle mechanics, and catalyst mobility, a framework not previously established for macroscopic CNT wire architectures at accelerator-representative fluences. These findings offer actionable design principles for wire diameter and treatment selection in beam diagnostic applications, including the High-Luminosity LHC and Future Circular Collider, with broader relevance to nuclear technologies and space systems.
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessRadiation tolerance of carbon nanotube wires: role of chemical treatment and wire structure
Carbon nanotube (CNT) wires are increasingly used in environments that experience intense radiation, yet their behaviour under energetic proton exposure remains insufficiently understood. This work compares treated and untreated wires of diameters 11, 19 and 50 micrometres irradiated at the CERN High Radiation to Materials facility with fluences between 1.2 × 1016 and 4.0 × 1016 protons per square centimetre.Treatment through nitric acid purification followed by controlled twisting and low temperature annealing increased carbon purity to 94–97 atomic percent and reduced aluminium and silicon contamination. All wires showed increased lattice disorder after treatment, with rising AD/AG ratios and G band broadening consistent with reduced graphitic coherence length. Smaller wires accommodated irradiation through distributed bundle sliding, exhibiting moderate expansion of 10–20% and preserved geometry. Larger wires exceeded the threshold for collective bundle slip, developing swelling of up to 40% with pronounced filament relaxation. Treatment stabilised the thinnest wires but intensified deformation in the thickest by raising internal stored strain energy. Iron associated with catalyst residues concentrated locally by nearly 50% after irradiation, consistent with thermally activated diffusion toward defect trapping sites.Radiation tolerance emerges from the coupling between lattice-level defect generation, mesoscale bundle mechanics, and catalyst mobility, a framework not previously established for macroscopic CNT wire architectures at accelerator-representative fluences. These findings offer actionable design principles for wire diameter and treatment selection in beam diagnostic applications, including the High-Luminosity LHC and Future Circular Collider, with broader relevance to nuclear technologies and space systems.
- Open Access
- 1 May 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (5)
A compact tensile tester for carbon nanotube wires
The exceptional stiffness and strength of carbon nanotube (CNT) wires have led to substantial progress in the synthesis of these materials for a broad range of high-performance applications. However, to date, there is a lack of suitable equipment to characterize the mechanical performance of these wires. In this study, a compact and low-cost tensile tester was developed to characterize CNT wires for use in accelerator beam wire scanners. The device combines a stepper-motor actuator, load cell, and a linear potentiometer under Arduino-based control, providing sub-micron displacement precision and milli-Newton digital force resolution. Compliance calibration was carried out using copper and nylon wires, demonstrating the reliability of the measurement system. Initial tensile tests on CNT yarns with diameters between 10 and 50 μm, from multiple commercial suppliers, revealed ultimate tensile strengths of 1–3 GPa and elastic moduli of 120–200 GPa, below manufacturer specifications, corresponding to reductions of ∼50% in strength and up to 60% in modulus depending on the sample. These results highlight challenges related to sample preparation, clamping, and the intrinsic variability of CNT assemblies. Despite these limitations, the instrument enables reproducible testing of fragile filaments and provides a foundation for systematic mechanical evaluation of CNT wires.
- 1 May 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (5)
Open AccessA compact tensile tester for carbon nanotube wires
The exceptional stiffness and strength of carbon nanotube (CNT) wires have led to substantial progress in the synthesis of these materials for a broad range of high-performance applications. However, to date, there is a lack of suitable equipment to characterize the mechanical performance of these wires. In this study, a compact and low-cost tensile tester was developed to characterize CNT wires for use in accelerator beam wire scanners. The device combines a stepper-motor actuator, load cell, and a linear potentiometer under Arduino-based control, providing sub-micron displacement precision and milli-Newton digital force resolution. Compliance calibration was carried out using copper and nylon wires, demonstrating the reliability of the measurement system. Initial tensile tests on CNT yarns with diameters between 10 and 50 μm, from multiple commercial suppliers, revealed ultimate tensile strengths of 1–3 GPa and elastic moduli of 120–200 GPa, below manufacturer specifications, corresponding to reductions of ∼50% in strength and up to 60% in modulus depending on the sample. These results highlight challenges related to sample preparation, clamping, and the intrinsic variability of CNT assemblies. Despite these limitations, the instrument enables reproducible testing of fragile filaments and provides a foundation for systematic mechanical evaluation of CNT wires.
- Open Access
- 22 August 2025
- Published by Elsevier in Materials & Design
- Vol. 258
Carbon nanotube wires for accelerator applications
- 22 August 2025
- Published by Elsevier in Materials & Design
- Vol. 258
Open AccessCarbon nanotube wires for accelerator applications
- Open Access
- 4 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (22) , 21540-21549
An Inertial Uni-Axial Interferometer-Based Accelerometer for Harsh Environments
For high-impact devices, subsequent vibrations have as much influence on the deterioration of the mechanical structure as the impact itself. To mitigate the consequences of both impacts and resulting vibrations, it is crucial to accurately understand the peak acceleration and vibration frequencies that originate in the structure. In this article, a radiation tolerant opto-mechanical sensor based on an absolute measurement inertial accelerometer is presented. This method of measurement is chosen due to the viability of placing the readout electronics far from the highly radioactive environment that the sensor may be installed in. The designed accelerometer consists of a fixed aluminum frame with a built-in membrane that acts as a leaf spring. In the same membrane, a retro-reflector is attached which acts as a seismic mass. The retro-reflector reflects the light beam coming from the collimator lens placed on the frame. To prove its viability, the device has been tested under different conditions. First, the device is calibrated and validated using a high-frequency exciter. Second, a high-acceleration testbench is used to compare its output signal with a commercial accelerometer and verify its proper operation as well as its expected lifetime. The experimental results showed an average sensitivity of ${9} \times {10}^{-{4}}$ g/pm with reading measurements of up to 5000 g and a working bandwidth located between 50 and 800 Hz.
- 4 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (22) , 21540-21549
Open AccessAn Inertial Uni-Axial Interferometer-Based Accelerometer for Harsh Environments
For high-impact devices, subsequent vibrations have as much influence on the deterioration of the mechanical structure as the impact itself. To mitigate the consequences of both impacts and resulting vibrations, it is crucial to accurately understand the peak acceleration and vibration frequencies that originate in the structure. In this article, a radiation tolerant opto-mechanical sensor based on an absolute measurement inertial accelerometer is presented. This method of measurement is chosen due to the viability of placing the readout electronics far from the highly radioactive environment that the sensor may be installed in. The designed accelerometer consists of a fixed aluminum frame with a built-in membrane that acts as a leaf spring. In the same membrane, a retro-reflector is attached which acts as a seismic mass. The retro-reflector reflects the light beam coming from the collimator lens placed on the frame. To prove its viability, the device has been tested under different conditions. First, the device is calibrated and validated using a high-frequency exciter. Second, a high-acceleration testbench is used to compare its output signal with a commercial accelerometer and verify its proper operation as well as its expected lifetime. The experimental results showed an average sensitivity of ${9} \times {10}^{-{4}}$ g/pm with reading measurements of up to 5000 g and a working bandwidth located between 50 and 800 Hz.