Oleg Sinchuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oleg Sinchuk has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Oleksii Mykhailenko
Kryvyi Rih National University, Department of Power Systems and Energy Management, 11 Vitalii Matusevysch Str., Kryvyi Rih, 50027, Ukraine
3 shared publications - Vladyslav Baranovskyi
Kryvyi Rih National University
3 shared publications - Danyil Kobeliatskyi2 shared publications
- Ihor Peresunko
Криворізький національний університет
2 shared publications - Ihor Sinchuk
Kryvyi Rih Natl Univ, UA-50027 Kryvyi Rih, Ukraine
2 shared publications - Mykhailo Rogoza
Dnipro Univ Technol, UA-49005 Dnipro, Ukraine
2 shared publications
Latest Publications
- 30 December 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (4) , 119-129
Adaptive control of power receivers supply voltage in underground mines
Purpose. This research aims to synthesize an automated system for stabilising the supply voltage of individual electrical consumers at iron ore mines when it deviates from standardised values due to unpredictable disturbances in the mine power systems. Methods. A dynamic voltage restorer was used to stabilize the supply voltage of mine electrical consumers. The basic control system for the dynamic voltage restorer was developed using control theory methods, such as linear-quadratic control. Heuristic optimization methods were used to adapt the linear-quadratic regulator to unpredictable disturbances. The control integral absolute error was taken as the criterion. Numerical analysis was used to check the quality of transients during voltage stabilization using the proposed system. Findings. The adaptive control system for a dynamic voltage restorer has been developed to stabilize the supply voltage of individual electrical consumers at iron ore mines. The optimal genetic algorithm parameters have been determined, including the population size and mutation rates of the linear-quadratic regulator weight matrices. It minimizes the integral absolute error and, as a result, eliminates overshoot (overshoot is no more than 0.058%) and reduces the transient time (up to 95%) compared to the unoptimized system. Originality. The method of adaptive automated linear-quadratic regulator tuning based on a genetic algorithm is proposed. For the first time, it is used to control a dynamic voltage restorer installed between the power grid and the mine electrical consumer. This method has enabled the compensation of fluctuations in the mine power grid voltage at the consumer end, without overshoot and with short settling times. Practical implications. The results can be used for the development of digital controllers embedded firmware for dynamic voltage restorers, providing real-time voltage fluctuation compensation and improving the power supply quality to mine electrical consumers.
- 30 December 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (4) , 119-129
Adaptive control of power receivers supply voltage in underground mines
Purpose. This research aims to synthesize an automated system for stabilising the supply voltage of individual electrical consumers at iron ore mines when it deviates from standardised values due to unpredictable disturbances in the mine power systems. Methods. A dynamic voltage restorer was used to stabilize the supply voltage of mine electrical consumers. The basic control system for the dynamic voltage restorer was developed using control theory methods, such as linear-quadratic control. Heuristic optimization methods were used to adapt the linear-quadratic regulator to unpredictable disturbances. The control integral absolute error was taken as the criterion. Numerical analysis was used to check the quality of transients during voltage stabilization using the proposed system. Findings. The adaptive control system for a dynamic voltage restorer has been developed to stabilize the supply voltage of individual electrical consumers at iron ore mines. The optimal genetic algorithm parameters have been determined, including the population size and mutation rates of the linear-quadratic regulator weight matrices. It minimizes the integral absolute error and, as a result, eliminates overshoot (overshoot is no more than 0.058%) and reduces the transient time (up to 95%) compared to the unoptimized system. Originality. The method of adaptive automated linear-quadratic regulator tuning based on a genetic algorithm is proposed. For the first time, it is used to control a dynamic voltage restorer installed between the power grid and the mine electrical consumer. This method has enabled the compensation of fluctuations in the mine power grid voltage at the consumer end, without overshoot and with short settling times. Practical implications. The results can be used for the development of digital controllers embedded firmware for dynamic voltage restorers, providing real-time voltage fluctuation compensation and improving the power supply quality to mine electrical consumers.
- 30 December 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 66-72
Improving the efficiency of street lighting electrical systems
Purpose. To derive mathematical expressions that, using the available information, will allow forecasting the levels of electricity consumption by the city’s outdoor lighting network in the main possible scenarios for several years ahead, as well as when developing an energy-efficient smart control system for the electrotechnical complex of lighting complex. Methodology. Creating an effective intelligent outdoor lighting control system involves the use of the following methods. First, using the empirical measurement method, information on illumination, electricity consumption, car and pedestrian traffic is obtained. Statistical methods are used to identify patterns and relationships between the measured values, as well as to make subsequent forecasts. For intelligent control of outdoor lighting, a decision-making method based on fuzzy inference is used, which allows one, based on information about the operating conditions of the outdoor lighting network, to determine the recommended value of the current or value of lighting devices and the required power source. This approach will ensure maximum system efficiency. Findings. The obtained analytical dependencies for forecasting the electricity consumption, which are based on data from different time intervals, have determination coefficients of 66.8 and 88.1 %, respectively. The simulation of the operation of a fuzzy control system for the electricity consumption of outdoor lighting on the example of an operated part of the road operated and illuminated by ten 100 W LED lamps for summer and winter nights with different discrete control steps confirms the possibility of achieving the efficiency of outdoor lighting when using the proposed controllability option. The combined-powered control system is more efficient, reducing electricity consumption in summer and winter by more than 70 % compared to traditional control schemes. Originality. A fuzzy control system for the electrical complex of outdoor lighting in cities is improved, which takes into account the electricity tariff in addition to the level of illumination and the car or pedestrian traffic when generating the control action for the LED driver and determining the rational power source (grid or grid/battery) for lighting devices. Practical value. The architecture of the system for controlling electricity consumption by electrical receivers of lighting networks based on the fuzzy inference algorithm is developed, which is recommended for use to ensure an increase in the energy efficiency of this class of municipal consumers.
- 30 December 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 66-72
Improving the efficiency of street lighting electrical systems
Purpose. To derive mathematical expressions that, using the available information, will allow forecasting the levels of electricity consumption by the city’s outdoor lighting network in the main possible scenarios for several years ahead, as well as when developing an energy-efficient smart control system for the electrotechnical complex of lighting complex. Methodology. Creating an effective intelligent outdoor lighting control system involves the use of the following methods. First, using the empirical measurement method, information on illumination, electricity consumption, car and pedestrian traffic is obtained. Statistical methods are used to identify patterns and relationships between the measured values, as well as to make subsequent forecasts. For intelligent control of outdoor lighting, a decision-making method based on fuzzy inference is used, which allows one, based on information about the operating conditions of the outdoor lighting network, to determine the recommended value of the current or value of lighting devices and the required power source. This approach will ensure maximum system efficiency. Findings. The obtained analytical dependencies for forecasting the electricity consumption, which are based on data from different time intervals, have determination coefficients of 66.8 and 88.1 %, respectively. The simulation of the operation of a fuzzy control system for the electricity consumption of outdoor lighting on the example of an operated part of the road operated and illuminated by ten 100 W LED lamps for summer and winter nights with different discrete control steps confirms the possibility of achieving the efficiency of outdoor lighting when using the proposed controllability option. The combined-powered control system is more efficient, reducing electricity consumption in summer and winter by more than 70 % compared to traditional control schemes. Originality. A fuzzy control system for the electrical complex of outdoor lighting in cities is improved, which takes into account the electricity tariff in addition to the level of illumination and the car or pedestrian traffic when generating the control action for the LED driver and determining the rational power source (grid or grid/battery) for lighting devices. Practical value. The architecture of the system for controlling electricity consumption by electrical receivers of lighting networks based on the fuzzy inference algorithm is developed, which is recommended for use to ensure an increase in the energy efficiency of this class of municipal consumers.
- 29 February 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 1,p. 84-91
Heuristic control of power consumption by up to 1000 V electrical loads at mining enterprises
Purpose. To develop a method for synthesizing the structure and algorithm of the system for automated control of power consumption by up to 1000 V electrical receivers at mining enterprises with iron ore underground mining methods. This enables direct control of the load connection to the industrial power grid to ensure minimum power costs depending on its cost per day ahead. Methodology. The problem of controlling power consumption of electrical receivers at iron ore underground mines is formalized as a binary form of mixed integer programming. To solve it, a binary implementation of the heuristic genetic algorithm is used. The mathematical modeling method analyzes the impact of genetic algorithm settings, such as the number of phenotypes in the population, the number of elite phenotypes that pass unchanged to the next generation, and the method of phenotype crossover on its quality. Findings. As a result of the research, it is found that the most effective way to control the process of power consumption based on an evolutionary genetic algorithm is to use the Laplace crossover function and keep the percentage of elite phenotypes in the population at 10 %. Moreover, at the smallest population size, the best accuracy is observed when using the Laplace function, while at one- and two-point crossover functions, it worsens, but not significantly (no more than 0.2 %). However, as the number of elite phenotypes increases, the duration of the evolutionary search in the control process is reduced by almost a factor of two in the case of one- and two-point crossovers. Originality. For the first time, the structure of a heuristic system for automated control of power consumption by underground electrical receivers with a supply voltage of up to 1000 V at iron ore underground mines has been developed on the basis of an evolutionary genetic algorithm. Depending on the designed volumes of ore production and the daily power cost per day, this allows determining the optimal power load schedule of underground distribution substations in advance, which, subject to the accepted limits on hourly and daily power, minimizes the cost of purchasing power, and thus reduces the cost of the final product. Practical value. The architecture of a heuristic system for controlling power consumption by electrical receivers with a voltage of up to 1000 V based on an evolutionary genetic algorithm is developed and recommended when optimizing the power load schedule of transformer substations of mining and metallurgical enterprises, in particular, of iron ore underground mines operating in this voltage class.
- 29 February 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 1,p. 84-91
Heuristic control of power consumption by up to 1000 V electrical loads at mining enterprises
Purpose. To develop a method for synthesizing the structure and algorithm of the system for automated control of power consumption by up to 1000 V electrical receivers at mining enterprises with iron ore underground mining methods. This enables direct control of the load connection to the industrial power grid to ensure minimum power costs depending on its cost per day ahead. Methodology. The problem of controlling power consumption of electrical receivers at iron ore underground mines is formalized as a binary form of mixed integer programming. To solve it, a binary implementation of the heuristic genetic algorithm is used. The mathematical modeling method analyzes the impact of genetic algorithm settings, such as the number of phenotypes in the population, the number of elite phenotypes that pass unchanged to the next generation, and the method of phenotype crossover on its quality. Findings. As a result of the research, it is found that the most effective way to control the process of power consumption based on an evolutionary genetic algorithm is to use the Laplace crossover function and keep the percentage of elite phenotypes in the population at 10 %. Moreover, at the smallest population size, the best accuracy is observed when using the Laplace function, while at one- and two-point crossover functions, it worsens, but not significantly (no more than 0.2 %). However, as the number of elite phenotypes increases, the duration of the evolutionary search in the control process is reduced by almost a factor of two in the case of one- and two-point crossovers. Originality. For the first time, the structure of a heuristic system for automated control of power consumption by underground electrical receivers with a supply voltage of up to 1000 V at iron ore underground mines has been developed on the basis of an evolutionary genetic algorithm. Depending on the designed volumes of ore production and the daily power cost per day, this allows determining the optimal power load schedule of underground distribution substations in advance, which, subject to the accepted limits on hourly and daily power, minimizes the cost of purchasing power, and thus reduces the cost of the final product. Practical value. The architecture of a heuristic system for controlling power consumption by electrical receivers with a voltage of up to 1000 V based on an evolutionary genetic algorithm is developed and recommended when optimizing the power load schedule of transformer substations of mining and metallurgical enterprises, in particular, of iron ore underground mines operating in this voltage class.
- 30 September 2023
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 17 (3) , 93-101
Model studies to identify input parameters of an algorithm controlling electric supply/consumption process by underground iron ore enterprises
Purpose is the development of the research format of a mathematical model to select and assess input parameters of an algorithm controlling distribution of electric energy flows in the monitoring structure of electricity supply/consumption by using equipment of mining enterprises engaged in underground iron ore raw materials extraction. Methods. The analytical research involved a theory of random processes adapted to the real conditions. For the purpose, results of experimental measurements have been applied obtained under the conditions of active iron ore enterprises using underground procedures of the raw materials mining. Methods of random functions (i.e. elements of correlation theory) have helped identify the basic input and output parameters characterizing rather completely electric supply consumption as a stochastic process to develop a control algorithm for the process. Findings. A mathematical model of an electric supply/consumption complex as a stochastic process has been developed to assess its features as well as its levels of influence on the economic operational indices of electric power system of under-ground mining enterprises. Formation of the algorithm to control distribution of electric power flows among consumers of the analyzed types of iron ore enterprises took into consideration stochastic nature of the mentioned complex activity. Originality. The procedure of electric supply/consumption by underground iron ore enterprises has been analyzed in the format of process of a stochastic process of their operation. For the first time, the synthesized mathematical model has been built; both average and disperse stochastic characteristics of electric consumption capacity have been identified; average period of electric energy consumption as a stationary random function during the specified time has been determined; and average number of electric consumption peaks for the interval has been defined as well as average duration of their surges. Analysis of the electric supply/consumption process as a stochastic process has helped solve a problem of the peak influence on the modes of electric energy consumption by receivers of the enterprises, i.e. the random function crossing the specified electric consumption level. Practical implications. According to the available computing formats, a calculation procedure of the operation parameters of electric supply/consumption is of insufficient accuracy since average values are applied and stochastic nature of the process is ignored, which is typical for the analyzed mining enterprises. The abovementioned restricts the possibility to develop adequate system to control the electric power process in terms of the types of mining enterprises and specificity of their operational technology. The developed methods of electric supply/consumption functioning dynamics as a stochastic process help expand its use while forming and making efficient managerial decisions in the context of the analyzed process.
- 30 September 2023
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 17 (3) , 93-101
Model studies to identify input parameters of an algorithm controlling electric supply/consumption process by underground iron ore enterprises
Purpose is the development of the research format of a mathematical model to select and assess input parameters of an algorithm controlling distribution of electric energy flows in the monitoring structure of electricity supply/consumption by using equipment of mining enterprises engaged in underground iron ore raw materials extraction. Methods. The analytical research involved a theory of random processes adapted to the real conditions. For the purpose, results of experimental measurements have been applied obtained under the conditions of active iron ore enterprises using underground procedures of the raw materials mining. Methods of random functions (i.e. elements of correlation theory) have helped identify the basic input and output parameters characterizing rather completely electric supply consumption as a stochastic process to develop a control algorithm for the process. Findings. A mathematical model of an electric supply/consumption complex as a stochastic process has been developed to assess its features as well as its levels of influence on the economic operational indices of electric power system of under-ground mining enterprises. Formation of the algorithm to control distribution of electric power flows among consumers of the analyzed types of iron ore enterprises took into consideration stochastic nature of the mentioned complex activity. Originality. The procedure of electric supply/consumption by underground iron ore enterprises has been analyzed in the format of process of a stochastic process of their operation. For the first time, the synthesized mathematical model has been built; both average and disperse stochastic characteristics of electric consumption capacity have been identified; average period of electric energy consumption as a stationary random function during the specified time has been determined; and average number of electric consumption peaks for the interval has been defined as well as average duration of their surges. Analysis of the electric supply/consumption process as a stochastic process has helped solve a problem of the peak influence on the modes of electric energy consumption by receivers of the enterprises, i.e. the random function crossing the specified electric consumption level. Practical implications. According to the available computing formats, a calculation procedure of the operation parameters of electric supply/consumption is of insufficient accuracy since average values are applied and stochastic nature of the process is ignored, which is typical for the analyzed mining enterprises. The abovementioned restricts the possibility to develop adequate system to control the electric power process in terms of the types of mining enterprises and specificity of their operational technology. The developed methods of electric supply/consumption functioning dynamics as a stochastic process help expand its use while forming and making efficient managerial decisions in the context of the analyzed process.
- Open Access
- 1 January 2022
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 2(28),p. 138-145
THE APPROACH TO STREET ELECTRIC LIGHTING COMPLEX MANAGEMENT WITH THE HELP OF A FUZZY REGULATOR
Street lighting networks are an integral part of the structure of communal economy of cities, towns and large settlements. Electrotechnical complexes of street lighting today are energy-intensive, therefore they need to be modernized in order to further their efficient operation and rational use of electrical energy. Today, it is possible to achieve such results only with the introduction of modern technologies and approaches to the construction of management systems.Modern elements of lighting systems areLED lighting devices, which are very economical and reliable. To date, the planned modernization of street lighting in the country's population centers is underway.Street lighting is an important component of the infrastructure of settlements. The quality of the functioning of the external lighting of populated areas is, on the one hand, a guarantee of people's comfort and the aesthetics of the surrounding space,and on the other hand, it affects the reduction of the number of traffic accidents and other criminal incidents.The purpose of this article is the theoretical justification of the approach to the management of the electrotechnical complex of street lighting, taking into account the multi-criterion of the input parameters to the control system.Taking into account the strategies for the development of control systems and the active implementation of distributed generation sources in various spheres of the world economy, including on the basis of renewable sources of electric energy, hybrid systems of artificial outdoor lighting controlled by intelligent control systems are being developed. The article proposes an approach to the management of the electrotechnical complex of street lighting. The proposed structure of the electrical complex of street lighting based on LED lighting devices and modern sources of electrical energy. Considering the multi-criterion of the input parameters to the control system of the electrotechnical complex of street lighting and the impossibility of precise preliminary determination of the parameters of these criteria, it was proposed to use the control law using the elements of fuzzy sets, which will improve the quality of regulation with the support of Fuzzy Logic commands.
- 1 January 2022
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 2(28),p. 138-145
Open AccessTHE APPROACH TO STREET ELECTRIC LIGHTING COMPLEX MANAGEMENT WITH THE HELP OF A FUZZY REGULATOR
Street lighting networks are an integral part of the structure of communal economy of cities, towns and large settlements. Electrotechnical complexes of street lighting today are energy-intensive, therefore they need to be modernized in order to further their efficient operation and rational use of electrical energy. Today, it is possible to achieve such results only with the introduction of modern technologies and approaches to the construction of management systems.Modern elements of lighting systems areLED lighting devices, which are very economical and reliable. To date, the planned modernization of street lighting in the country's population centers is underway.Street lighting is an important component of the infrastructure of settlements. The quality of the functioning of the external lighting of populated areas is, on the one hand, a guarantee of people's comfort and the aesthetics of the surrounding space,and on the other hand, it affects the reduction of the number of traffic accidents and other criminal incidents.The purpose of this article is the theoretical justification of the approach to the management of the electrotechnical complex of street lighting, taking into account the multi-criterion of the input parameters to the control system.Taking into account the strategies for the development of control systems and the active implementation of distributed generation sources in various spheres of the world economy, including on the basis of renewable sources of electric energy, hybrid systems of artificial outdoor lighting controlled by intelligent control systems are being developed. The article proposes an approach to the management of the electrotechnical complex of street lighting. The proposed structure of the electrical complex of street lighting based on LED lighting devices and modern sources of electrical energy. Considering the multi-criterion of the input parameters to the control system of the electrotechnical complex of street lighting and the impossibility of precise preliminary determination of the parameters of these criteria, it was proposed to use the control law using the elements of fuzzy sets, which will improve the quality of regulation with the support of Fuzzy Logic commands.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 190-193
Analysis of Direct Torque Control System of Five-Phase Induction Motor
In the work by mathematical modeling, an analysis of the functioning of the direct torque control system of a five-phase induction motor with a table of optimal switching, using only space voltage vectors with the maximum value, as well as with the use of the modified multi-level relay torque controller with the corresponding correction of the table of optimal switching, was performed. It has been proved that the use of multi-level relay torque controller can improve the accuracy of the torque control and reduce the level of torque ripples for five-phase induction motor drive.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 190-193
Analysis of Direct Torque Control System of Five-Phase Induction Motor
In the work by mathematical modeling, an analysis of the functioning of the direct torque control system of a five-phase induction motor with a table of optimal switching, using only space voltage vectors with the maximum value, as well as with the use of the modified multi-level relay torque controller with the corresponding correction of the table of optimal switching, was performed. It has been proved that the use of multi-level relay torque controller can improve the accuracy of the torque control and reduce the level of torque ripples for five-phase induction motor drive.