Kenichi Higuchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Kenichi Higuchi has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Junji Nagata
Process Research Laboratories, Nippon Steel Corporation
4 shared publications- Masaru Matsumura
Process Research Laboratories, Nippon Steel Corporation
4 shared publications Ryota Kosugi
Kitanihon Steel Works, Nippon Steel Corporation
2 shared publicationsYuichiro Yamamoto
Kitanihon Steel Works, Nippon Steel Corporation
2 shared publications- Benchao Su
Center for Advanced Research of Energy and Materials, Faculty of Engineering, Hokkaido University, Kita 13 Nishi 5, Kita-ku, Sapporo 060-8628, Japan
1 shared publication - Dairoku Muramatsu
The University of Electro-Communications , 1-5-1 Chofugaoka, Chofu, Tokyo 182-8585
1 shared publication
Latest Publications
- Open Access
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 771-780
Effect of Decreasing Gas Flow Rate between Two Ignition Furnaces on Sinter Yield at REMO-tec (Re-ignition sintering) Process
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer. As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility.This paper focuses on gas flow rate control between first ignition and re-ignition for the purpose of further improving product yield.It has been clear that certain decrease of gas flow rate between these two ignitions, has an effect on increasing heat storage amount in coke combustion zone at re-ignition caused by controlling vertical position of coke combustion zone.This method has been applied in Kimitsu No.3sinter plant. Product yield improves by 0.3% with increasing high temperature holding time.
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 771-780
Open AccessEffect of Decreasing Gas Flow Rate between Two Ignition Furnaces on Sinter Yield at REMO-tec (Re-ignition sintering) Process
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer. As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility.This paper focuses on gas flow rate control between first ignition and re-ignition for the purpose of further improving product yield.It has been clear that certain decrease of gas flow rate between these two ignitions, has an effect on increasing heat storage amount in coke combustion zone at re-ignition caused by controlling vertical position of coke combustion zone.This method has been applied in Kimitsu No.3sinter plant. Product yield improves by 0.3% with increasing high temperature holding time.
- Open Access
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 793-802
Effect of Re-ignition Method on Sinter Yield Through Improving Carbon Combustion Ratio at Upper Layer of Sinter Packed Bed
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer.As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility. This effect leads to improving sinter reducibility without decreasing sinter yield by decreasing control of coke breeze content in sinter mixture.This paper focuses on coke combustion efficiency as combustion ratio of carbon in coke breeze for considering improvement of sinter yield through sinter pot test. Here, carbon combustion ratio is defined as proportion of actual heat generation at combustion to ideal heat generation as complete combustion (C+O2→CO2) of all carbon in coke. And it can be calculated based on component analyses of exhaust gas.As the result, it was confirmed as shown bellows.1) By re- ignition, the unburned coke remaining in the upper layer of the sinter packed bed was burned, which has a role of extending keeping time over 1200℃ especially in the upper layer of sinter packed bed.2) Due to the effect of 1), the increasing amount of heat supply at “REMO-tec” case was equivalent to the same as the experimental case of increasing coke breeze content, at which increasing heat amount at blending coke breeze content was four times larger of the heat amount at re-ignition. (For a 430 mm layer pot test)3) In addition, since the re-ignition heat is donated to the upper layer (surface layer), the amount of heat consumption in the upper layer of the sinter packed bed increases and the amount of heat consumption in the lower layer decreases compared to the case of increasing coke breeze content, which results in decrease of the difference between heat consumption in upper layer and that in lower layer.In addition, these effects have been also confirmed at the commercial sinter plant.
- 15 August 2025
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 111 (12) , 793-802
Open AccessEffect of Re-ignition Method on Sinter Yield Through Improving Carbon Combustion Ratio at Upper Layer of Sinter Packed Bed
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer.As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility. This effect leads to improving sinter reducibility without decreasing sinter yield by decreasing control of coke breeze content in sinter mixture.This paper focuses on coke combustion efficiency as combustion ratio of carbon in coke breeze for considering improvement of sinter yield through sinter pot test. Here, carbon combustion ratio is defined as proportion of actual heat generation at combustion to ideal heat generation as complete combustion (C+O2→CO2) of all carbon in coke. And it can be calculated based on component analyses of exhaust gas.As the result, it was confirmed as shown bellows.1) By re- ignition, the unburned coke remaining in the upper layer of the sinter packed bed was burned, which has a role of extending keeping time over 1200℃ especially in the upper layer of sinter packed bed.2) Due to the effect of 1), the increasing amount of heat supply at “REMO-tec” case was equivalent to the same as the experimental case of increasing coke breeze content, at which increasing heat amount at blending coke breeze content was four times larger of the heat amount at re-ignition. (For a 430 mm layer pot test)3) In addition, since the re-ignition heat is donated to the upper layer (surface layer), the amount of heat consumption in the upper layer of the sinter packed bed increases and the amount of heat consumption in the lower layer decreases compared to the case of increasing coke breeze content, which results in decrease of the difference between heat consumption in upper layer and that in lower layer.In addition, these effects have been also confirmed at the commercial sinter plant.
- Open Access
- 30 May 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (6) , 817-824
Structural Analysis of Sinter Packed-bed during Softening and Melting Processes Using X-ray CT
In this study, changes in structure of sinter packed-bed during softening and melting processes were analyzed, and gas permeability of the cohesive layer was evaluated using X-ray CT images. First, the void structure of sinter packed-bed during softening and melting processes was visualized by X-ray CT images. In the softening process, the reducing gas flowed through the void between the sinter particles. In contrast, the reducing gas flowed through the generated melt phase in the melting process. Next, the changes in porosity and apparent particle diameter due to shrinkage of sinter layer were analyzed using CT images to evaluate the structural changes of sinter packed-bed during softening process. The porosity decreased with increasing the shrinkage of the sinter layer. In addition, the porosity tended to be smaller in the upper layer. The apparent particle diameter increased with increasing the shrinkage of the sinter layer. This is attributed to the deformation and the fusion of the sinter particles. Finally, the pressure drop of the sinter layer was calculated based on the Ergun equation using the porosity and the apparent particle diameter obtained from the CT images. As a result, the change in pressure drop was able to be well expressed up to a shrinkage degree of 0.5. The pressure drop was higher in the upper part of the sinter layer, suggesting that the pressure drop could be reduced by suppressing local blockage of the packed-bed.
- 30 May 2025
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 65 (6) , 817-824
Open AccessStructural Analysis of Sinter Packed-bed during Softening and Melting Processes Using X-ray CT
In this study, changes in structure of sinter packed-bed during softening and melting processes were analyzed, and gas permeability of the cohesive layer was evaluated using X-ray CT images. First, the void structure of sinter packed-bed during softening and melting processes was visualized by X-ray CT images. In the softening process, the reducing gas flowed through the void between the sinter particles. In contrast, the reducing gas flowed through the generated melt phase in the melting process. Next, the changes in porosity and apparent particle diameter due to shrinkage of sinter layer were analyzed using CT images to evaluate the structural changes of sinter packed-bed during softening process. The porosity decreased with increasing the shrinkage of the sinter layer. In addition, the porosity tended to be smaller in the upper layer. The apparent particle diameter increased with increasing the shrinkage of the sinter layer. This is attributed to the deformation and the fusion of the sinter particles. Finally, the pressure drop of the sinter layer was calculated based on the Ergun equation using the porosity and the apparent particle diameter obtained from the CT images. As a result, the change in pressure drop was able to be well expressed up to a shrinkage degree of 0.5. The pressure drop was higher in the upper part of the sinter layer, suggesting that the pressure drop could be reduced by suppressing local blockage of the packed-bed.
- Open Access
- 15 October 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (10) , 1647-1657
Reduction of Nitrogen Oxides by Calcium Ferrites in an Iron Ore Sintering Plant
In iron ore sintering plants, the emissions of nitrogen oxides (NOx) must be reduced. Previous studies have shown that calcium ferrites could significantly reduce NOx emissions. However, the reaction paths between calcium ferrites and NOx have not been clarified yet. In this study, NOx reduction tests were conducted at 1073 K–1373 K with a CO/CO2 ratio of 0.03–0.10. Accordingly, the phase compositions of calcium ferrites before and after NOx reduction were investigated. CaO·FeO·Fe2O3 (CWF), which had a significant effect on NOx reduction, was formed with a CO/CO2 ratio of 0.03–0.10. Based on the phase compositions of the calcium ferrites before and after NOx reduction, we determined that the CWF reduced the amounts of NOx, and CaO·Fe2O3 (CF), 2CaO·Fe2O3 (C2F), and Fe3O4 are produced from the CWF. The NOx reduction behavior during coke combustion tests was also investigated. By coating a mixture of iron ore and quicklime around the coke, NOx formation was decreased during coke combustion. This phenomenon may have been caused by the formation of reduced calcium ferrites from a mixture of iron ore and quicklime on the coke surface.
- 15 October 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (10) , 1647-1657
Open AccessReduction of Nitrogen Oxides by Calcium Ferrites in an Iron Ore Sintering Plant
In iron ore sintering plants, the emissions of nitrogen oxides (NOx) must be reduced. Previous studies have shown that calcium ferrites could significantly reduce NOx emissions. However, the reaction paths between calcium ferrites and NOx have not been clarified yet. In this study, NOx reduction tests were conducted at 1073 K–1373 K with a CO/CO2 ratio of 0.03–0.10. Accordingly, the phase compositions of calcium ferrites before and after NOx reduction were investigated. CaO·FeO·Fe2O3 (CWF), which had a significant effect on NOx reduction, was formed with a CO/CO2 ratio of 0.03–0.10. Based on the phase compositions of the calcium ferrites before and after NOx reduction, we determined that the CWF reduced the amounts of NOx, and CaO·Fe2O3 (CF), 2CaO·Fe2O3 (C2F), and Fe3O4 are produced from the CWF. The NOx reduction behavior during coke combustion tests was also investigated. By coating a mixture of iron ore and quicklime around the coke, NOx formation was decreased during coke combustion. This phenomenon may have been caused by the formation of reduced calcium ferrites from a mixture of iron ore and quicklime on the coke surface.
- 22 August 2023
- Published by Elsevier in Minerals Engineering
- Vol. 203
Effects of various factors on gangue removal in alkaline hydrothermal treatment of iron ores
- 22 August 2023
- Published by Elsevier in Minerals Engineering
- Vol. 203
Effects of various factors on gangue removal in alkaline hydrothermal treatment of iron ores
- Open Access
- 15 June 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (6) , 1002-1010
Effect of Re-ignition Method on Sinter Yield Through Improving Carbon Combustion Ratio at Upper Layer of Sinter Packed Bed
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer.As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility. This effect leads to improving sinter reducibility without decreasing sinter yield by decreasing control of coke breeze content in sinter mixture.This paper focuses on coke combustion efficiency as combustion ratio of carbon in coke breeze for considering improvement of sinter yield through sinter pot test. Here, carbon combustion ratio is defined as proportion of actual heat generation at combustion to ideal heat generation as complete combustion (C+O2→CO2) of all carbon in coke. And it can be calculated based on component analyses of exhaust gas.As the result, it was confirmed as shown bellows.1) By re- ignition, the unburned coke remaining in the upper layer of the sinter packed bed was burned, which has a role of extending keeping time over 1200°C especially in the upper layer of sinter packed bed.2) Due to the effect of 1), the increasing amount of heat supply at “REMO-tec” case was equivalent to the same as the experimental case of increasing coke breeze content, at which increasing heat amount at blending coke breeze content was four times larger of the heat amount at re-ignition. (For a 430 mm layer pot test)3) In addition, since the re-ignition heat is donated to the upper layer (surface layer), the amount of heat consumption in the upper layer of the sinter packed bed increases and the amount of heat consumption in the lower layer decreases compared to the case of increasing coke breeze content, which results in decrease of the difference between heat consumption in upper layer and that in lower layer.In addition, these effects have been also confirmed at the commercial sinter plant.
- 15 June 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (6) , 1002-1010
Open AccessEffect of Re-ignition Method on Sinter Yield Through Improving Carbon Combustion Ratio at Upper Layer of Sinter Packed Bed
Conventionally, it has been known that the product yield of the upper part of the sintering layer is extremely low, because of the heat loss caused by transferring heat toward the space above sintering layer, and of the large amount of unburned carbon in upper sintering layer.As a countermeasure, REMO-tec (Re-ignition Method for Optimization of Total Energy Consumption) has been developed. Here, REMO-tec, is the sintering technique of re-igniting sintering packed bed at certain intervals after first ignition. This method has an effect on improving sinter yield with maintaining high sinter reducibility. This effect leads to improving sinter reducibility without decreasing sinter yield by decreasing control of coke breeze content in sinter mixture.This paper focuses on coke combustion efficiency as combustion ratio of carbon in coke breeze for considering improvement of sinter yield through sinter pot test. Here, carbon combustion ratio is defined as proportion of actual heat generation at combustion to ideal heat generation as complete combustion (C+O2→CO2) of all carbon in coke. And it can be calculated based on component analyses of exhaust gas.As the result, it was confirmed as shown bellows.1) By re- ignition, the unburned coke remaining in the upper layer of the sinter packed bed was burned, which has a role of extending keeping time over 1200°C especially in the upper layer of sinter packed bed.2) Due to the effect of 1), the increasing amount of heat supply at “REMO-tec” case was equivalent to the same as the experimental case of increasing coke breeze content, at which increasing heat amount at blending coke breeze content was four times larger of the heat amount at re-ignition. (For a 430 mm layer pot test)3) In addition, since the re-ignition heat is donated to the upper layer (surface layer), the amount of heat consumption in the upper layer of the sinter packed bed increases and the amount of heat consumption in the lower layer decreases compared to the case of increasing coke breeze content, which results in decrease of the difference between heat consumption in upper layer and that in lower layer.In addition, these effects have been also confirmed at the commercial sinter plant.
- Open Access
- 15 November 2022
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 62 (11) , 2244-2254
Improvement of Sinter Productivity and Qualities by Placing Low Slag Green Pellet at Lower Layer of Sinter Packed Bed
In order to blend PF (pellet feed) or concentrates for 20 mass% in sinter mixture and to displace coke fines or anthracite to biomass for 25 mass% in BAR (Bonding Agent Rate), sinter packed bed has been designed in ISIJ Research workshop. Outline of the design is shown as below.As designing, most important factor is permeability, and it has to be maintained even though fine materials as PF or concentrates is highly blended (20 mass%). For high permeability, GP [Green Pellet] granulated from fine materials, is placed in lower layer of raw materials packed bed. In the lower layer, mill scale and biomass char, which has characteristic of different oxidation or combustion temperature and rate compared to coke fine, are placed with coke fines for keeping high temperature (>1200°C), because GP needs longer sintering time due to large diameter. In addition, chemical composition of GP is low bacisity (1.5) and low CaO content for keeping its shape through restricting melt formation at sintering. Restricting melt formation has possibility of improving sinter quality (RI,RDI).In this study, Effect of the packed bed mentioned above on sinter performance and quality has been confirmed by sintering simulator which has performance of continuous charging and igniting with moving pallet car.The main results are shown as below.1) Sintering speed and product yield are maintained at blending 20 mass% of PF. So, sinter productivity are also maintained.2) Sinter reducibility (RI) has been improved in addition to maintaining sinter reduction disintegration index(RDI) because of low FeO and low SiO2 content and restricting secondary hematite formation as mineral of sinter.3) Remaining object is recovering sinter strength (TI) at the condition of low CaO content in sinter.
- 15 November 2022
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 62 (11) , 2244-2254
Open AccessImprovement of Sinter Productivity and Qualities by Placing Low Slag Green Pellet at Lower Layer of Sinter Packed Bed
In order to blend PF (pellet feed) or concentrates for 20 mass% in sinter mixture and to displace coke fines or anthracite to biomass for 25 mass% in BAR (Bonding Agent Rate), sinter packed bed has been designed in ISIJ Research workshop. Outline of the design is shown as below.As designing, most important factor is permeability, and it has to be maintained even though fine materials as PF or concentrates is highly blended (20 mass%). For high permeability, GP [Green Pellet] granulated from fine materials, is placed in lower layer of raw materials packed bed. In the lower layer, mill scale and biomass char, which has characteristic of different oxidation or combustion temperature and rate compared to coke fine, are placed with coke fines for keeping high temperature (>1200°C), because GP needs longer sintering time due to large diameter. In addition, chemical composition of GP is low bacisity (1.5) and low CaO content for keeping its shape through restricting melt formation at sintering. Restricting melt formation has possibility of improving sinter quality (RI,RDI).In this study, Effect of the packed bed mentioned above on sinter performance and quality has been confirmed by sintering simulator which has performance of continuous charging and igniting with moving pallet car.The main results are shown as below.1) Sintering speed and product yield are maintained at blending 20 mass% of PF. So, sinter productivity are also maintained.2) Sinter reducibility (RI) has been improved in addition to maintaining sinter reduction disintegration index(RDI) because of low FeO and low SiO2 content and restricting secondary hematite formation as mineral of sinter.3) Remaining object is recovering sinter strength (TI) at the condition of low CaO content in sinter.
- 9 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 309-310
Measurement Frequency Evaluation for Bioimpedance-Based Blood-Glucose Estimation
Daily and continuous measurement of glycemia is vital for managing diabetes. To improve a patient's quality of life, we propose non-invasive glycemia monitoring based on bioimpedance. This study aims to investigate the optimal frequency band for bioimpedance-measurement to estimate the blood-glucose level. We clarify the frequency characteristics of the correlation coefficient between blood-glucose level and bioimpedance from the subject experiment. It is found that the frequency band below 40 kHz is a candidate for stable estimation.
- 9 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 309-310
Measurement Frequency Evaluation for Bioimpedance-Based Blood-Glucose Estimation
Daily and continuous measurement of glycemia is vital for managing diabetes. To improve a patient's quality of life, we propose non-invasive glycemia monitoring based on bioimpedance. This study aims to investigate the optimal frequency band for bioimpedance-measurement to estimate the blood-glucose level. We clarify the frequency characteristics of the correlation coefficient between blood-glucose level and bioimpedance from the subject experiment. It is found that the frequency band below 40 kHz is a candidate for stable estimation.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 2007 IEEE 66th Vehicular Technology Conference
- No. 10903038,p. 1390-1395
Investigations on Synchronization Channel Sequences in OFDM Based Evolved UTRA Downlink
This paper presents the optimum primary- synchronization channel (P-SCH) and secondary-SCH (S-SCH) sequences for the SCH based on criteria to achieve fast initial and neighboring cell search time performance in the Evolved UTRA (E-UTRA) downlink. Simulation results show that the P-SCH sequence has a slight influence on the achievable cell search time, and that the application of multiple sequences, i.e., three P-SCH sequences, is beneficial in achieving fast cell search time performance particularly for the neighboring cell search. The results also show that the Walsh-Hadamard sequence or cyclic-shifted orthogonal sequence is suitable for the S-SCH sequence to indicate the cell ID group. Furthermore, it is shown that the combination of a permutation of the orthogonal S-SCH and P-SCH-specific scrambling sequences is advantageous in suppressing the cross-correlation between S-SCHs that collide and in achieving a fast cell search time particularly for the neighboring cell search in inter-node B synchronous operation.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in 2007 IEEE 66th Vehicular Technology Conference
- No. 10903038,p. 1390-1395
Investigations on Synchronization Channel Sequences in OFDM Based Evolved UTRA Downlink
This paper presents the optimum primary- synchronization channel (P-SCH) and secondary-SCH (S-SCH) sequences for the SCH based on criteria to achieve fast initial and neighboring cell search time performance in the Evolved UTRA (E-UTRA) downlink. Simulation results show that the P-SCH sequence has a slight influence on the achievable cell search time, and that the application of multiple sequences, i.e., three P-SCH sequences, is beneficial in achieving fast cell search time performance particularly for the neighboring cell search. The results also show that the Walsh-Hadamard sequence or cyclic-shifted orthogonal sequence is suitable for the S-SCH sequence to indicate the cell ID group. Furthermore, it is shown that the combination of a permutation of the orthogonal S-SCH and P-SCH-specific scrambling sequences is advantageous in suppressing the cross-correlation between S-SCHs that collide and in achieving a fast cell search time particularly for the neighboring cell search in inter-node B synchronous operation.
- 1 January 2000
- Published by Elsevier in Computers & Structures
- Vol. 74 (1) , 11-19
r- and hr-adaptive boundary element method for two-dimensional potential problem
- 1 January 2000
- Published by Elsevier in Computers & Structures
- Vol. 74 (1) , 11-19
r- and hr-adaptive boundary element method for two-dimensional potential problem