Muhammed Emin Erdin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammed Emin Erdin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Cengiz Baykasoglu
Hitit Üniversitesi
3 shared publications - Adil Baykasoğlu
Dokuz Eylül Üniversitesi
2 shared publications - Erhan Cetin
Hitit University
2 shared publications Adil Baykasoğlu
1 shared publication- Ali Özgedik1 shared publication
- Ali Özgedi̇k
Gazi Üniversitesi
1 shared publication
Latest Publications
- Open Access
- 30 July 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (17) , 15776-15792
Compression behavior and design optimization of triggered glass fiber reinforced polymer square tubes
Glass fiber reinforced polymer (GFRP) composite tubes have become increasingly popular in crashworthiness applications. On the other hand, square section GFRP tubes are prone to damage in a catastrophic failure mode in the early stages of the crushing process. At this point, triggering mechanisms have great potential to ensure deformation in progressive mode and improve the compression performance of GFRP tubes. Motivated by these facts, this paper aims to optimize the compression performance of square GFRP tubes by implementing notch‐type triggering mechanisms. The effects of notch width, number and length on the axial compression response of tubes were investigated to determine the optimal trigger configurations that would maximize specific energy absorption (SEA) and minimize peak crushing force (PCF). Experiments were conducted based on Taguchi L9 orthogonal array design, and Taguchi coupled Weighted Aggregated Sum Product Assessment (WASPAS) method was employed for optimizing multiple responses. The optimization results revealed that the proposed trigger mechanisms induced progressive crushing by preventing catastrophic failure, thereby significantly improving the compression performance of GFRP tubes. In particular, the results showed that the PCF of intact GFRP tube decreased by up to 38%, while SEA increased by up to 130% with the help of proposed trigger mechanism. Highlights: The compression performance of square GFRP tubes improved by notch‐type triggering. The notch width, length and number were chosen as design parameters. Taguchi experimental design was used to find the best configuration of design parameters. The optimum configurations were examined through the entropy‐WASPAS approach. The results revealed that significant improvements can be achieved using trigger mechanism.
- 30 July 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (17) , 15776-15792
Open AccessCompression behavior and design optimization of triggered glass fiber reinforced polymer square tubes
Glass fiber reinforced polymer (GFRP) composite tubes have become increasingly popular in crashworthiness applications. On the other hand, square section GFRP tubes are prone to damage in a catastrophic failure mode in the early stages of the crushing process. At this point, triggering mechanisms have great potential to ensure deformation in progressive mode and improve the compression performance of GFRP tubes. Motivated by these facts, this paper aims to optimize the compression performance of square GFRP tubes by implementing notch‐type triggering mechanisms. The effects of notch width, number and length on the axial compression response of tubes were investigated to determine the optimal trigger configurations that would maximize specific energy absorption (SEA) and minimize peak crushing force (PCF). Experiments were conducted based on Taguchi L9 orthogonal array design, and Taguchi coupled Weighted Aggregated Sum Product Assessment (WASPAS) method was employed for optimizing multiple responses. The optimization results revealed that the proposed trigger mechanisms induced progressive crushing by preventing catastrophic failure, thereby significantly improving the compression performance of GFRP tubes. In particular, the results showed that the PCF of intact GFRP tube decreased by up to 38%, while SEA increased by up to 130% with the help of proposed trigger mechanism. Highlights: The compression performance of square GFRP tubes improved by notch‐type triggering. The notch width, length and number were chosen as design parameters. Taguchi experimental design was used to find the best configuration of design parameters. The optimum configurations were examined through the entropy‐WASPAS approach. The results revealed that significant improvements can be achieved using trigger mechanism.
- Open Access
- 19 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (6) , 5504-5521
Effect of triggering on the axial crushing behavior of GFRP tubes: Experimental investigation and optimization
Composite thin‐walled tubes made of glass fiber reinforced plastics (GFRP) are attracting great attention due to their lightweight and outstanding crashworthiness capacity. Implementing triggers to the design of GFRP composite tubes enables a further increase in specific energy absorption while simultaneously reducing peak crushing force. Motivated by these facts, a notch‐type triggering mechanism is suggested in this work to enhance the energy absorption capabilities of circular GFRP composite tubes. GFRP tube samples with (0°/90°)8 layups are manufactured using the roll wrapping process. Subsequently, these samples are triggered and subjected to quasi‐static axial compression tests. The diameter, quantity and placement of the triggering notches are selected as design parameters, and experiments are carried out using Taguchi's L9 orthogonal array. Each of these parameters has three levels to identify the optimal combination of design parameters. To optimize multiple responses, the weighted aggregated sum product assessment, a multiple criteria decision‐making technique, is employed in conjunction with mono‐criteria optimization. The findings indicated that substantial enhancements can be realized in all parameters related to energy absorption performance by triggering progressive crushing modes in a controlled manner using a notch‐type triggering mechanism. In particular, the findings indicated that the specific energy absorption and the crush force efficiency of the intact GFRP composite tubes could be improved up to 18% and 68.3%, respectively, by the selection of appropriate triggering parameters.Highlights: Axial crushing and optimal design of triggered GFRP tubes are investigated Number, diameter, and center distance of the notches are chosen as parameters Taguchi experimental design is used for the best configuration of parameters The optimum configurations are investigated using the entropy‐WASPAS Significant improvements are achieved using the trigger mechanism
- 19 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (6) , 5504-5521
Open AccessEffect of triggering on the axial crushing behavior of GFRP tubes: Experimental investigation and optimization
Composite thin‐walled tubes made of glass fiber reinforced plastics (GFRP) are attracting great attention due to their lightweight and outstanding crashworthiness capacity. Implementing triggers to the design of GFRP composite tubes enables a further increase in specific energy absorption while simultaneously reducing peak crushing force. Motivated by these facts, a notch‐type triggering mechanism is suggested in this work to enhance the energy absorption capabilities of circular GFRP composite tubes. GFRP tube samples with (0°/90°)8 layups are manufactured using the roll wrapping process. Subsequently, these samples are triggered and subjected to quasi‐static axial compression tests. The diameter, quantity and placement of the triggering notches are selected as design parameters, and experiments are carried out using Taguchi's L9 orthogonal array. Each of these parameters has three levels to identify the optimal combination of design parameters. To optimize multiple responses, the weighted aggregated sum product assessment, a multiple criteria decision‐making technique, is employed in conjunction with mono‐criteria optimization. The findings indicated that substantial enhancements can be realized in all parameters related to energy absorption performance by triggering progressive crushing modes in a controlled manner using a notch‐type triggering mechanism. In particular, the findings indicated that the specific energy absorption and the crush force efficiency of the intact GFRP composite tubes could be improved up to 18% and 68.3%, respectively, by the selection of appropriate triggering parameters.Highlights: Axial crushing and optimal design of triggered GFRP tubes are investigated Number, diameter, and center distance of the notches are chosen as parameters Taguchi experimental design is used for the best configuration of parameters The optimum configurations are investigated using the entropy‐WASPAS Significant improvements are achieved using the trigger mechanism
- Open Access
- 15 November 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (5) , 1
Effects of Heat Treatment on Microstructure and Impact Resistance of High Manganese Steels
High manganese steels are widely used as wear- and impact-resistant materials in many areas, especially in the mining, construction, cement, and metallurgy sectors, where it is extremely important to be able to work safely in high-stress conditions as well as resistance to abrasion under heavy loading conditions thanks to their unique work-hardening performance. At this point, the carbon and manganese ratio of the material has a considerable influence on the microstructure of the cast part after the heat treatment. Therefore, heat treatment conditions have to be determined appropriately depending on the chemical composition of the material. In this study, heat treatment processes were applied to high manganese steel specimens having GX120MnCr18-2 DIN standard at various austenitizing temperatures between 1030~1100 oC. The specimens were examined under an optical microscope and SEM/EDS analyses were performed. Impact resistance and hardness values of the above-mentioned specimens were measured via the tests performed with TS EN ISO 148-1 and TS EN 130 6508-1 standards, respectively. From these investigations, it was determined that the carbide solubility increased as the austenitizing temperature increased while the impact resistance first increased and then decreased.
- 15 November 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (5) , 1
Open AccessEffects of Heat Treatment on Microstructure and Impact Resistance of High Manganese Steels
High manganese steels are widely used as wear- and impact-resistant materials in many areas, especially in the mining, construction, cement, and metallurgy sectors, where it is extremely important to be able to work safely in high-stress conditions as well as resistance to abrasion under heavy loading conditions thanks to their unique work-hardening performance. At this point, the carbon and manganese ratio of the material has a considerable influence on the microstructure of the cast part after the heat treatment. Therefore, heat treatment conditions have to be determined appropriately depending on the chemical composition of the material. In this study, heat treatment processes were applied to high manganese steel specimens having GX120MnCr18-2 DIN standard at various austenitizing temperatures between 1030~1100 oC. The specimens were examined under an optical microscope and SEM/EDS analyses were performed. Impact resistance and hardness values of the above-mentioned specimens were measured via the tests performed with TS EN ISO 148-1 and TS EN 130 6508-1 standards, respectively. From these investigations, it was determined that the carbide solubility increased as the austenitizing temperature increased while the impact resistance first increased and then decreased.
- 16 November 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Experimental investigation of the axial crushing behavior of aluminum/CFRP hybrid tubes with circular-hole triggering mechanism
- 16 November 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 182
Experimental investigation of the axial crushing behavior of aluminum/CFRP hybrid tubes with circular-hole triggering mechanism
- 6 November 2019
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 33 (11) , 5383-5392
Deep drawing of polymer coated metal sheets
- 6 November 2019
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 33 (11) , 5383-5392
Deep drawing of polymer coated metal sheets
- Open Access
- 30 June 2018
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 6 (2) , 308-318
Elektro Erozyon ile İşlemede İşleme Haznesine Uygulanan Titreşimlerin Geometrik Elektrot Aşınması Üzerindeki Etkilerinin İncelenmesi
Bu çalışmada, Elektro Erozyon ile İşleme (EEİ) tekniğinde işleme haznesine uygulanan titreşimlerin elektrot köşe aşınma geometrisi ve performans çıktıları üzerindeki etkilerinin incelenmesi için titreşim frekansı, boşalım akımı ve vurum süresi gibi farklı işleme koşullarında deneyler yapılmıştır. İşleme haznesi titreşimli (İHT-EEİ) deneylerde titreşimsiz koşullara göre elektrot aşınma hızı (EAH) ve bağıl aşınma (BA) değerleri azalmıştır. Deneysel sonuçlara göre işleme haznesine uygulanan titreşimler elektrot köşe yarıçap değerlerinde azalmaya neden olmuştur.
- 30 June 2018
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 6 (2) , 308-318
Open AccessElektro Erozyon ile İşlemede İşleme Haznesine Uygulanan Titreşimlerin Geometrik Elektrot Aşınması Üzerindeki Etkilerinin İncelenmesi
Bu çalışmada, Elektro Erozyon ile İşleme (EEİ) tekniğinde işleme haznesine uygulanan titreşimlerin elektrot köşe aşınma geometrisi ve performans çıktıları üzerindeki etkilerinin incelenmesi için titreşim frekansı, boşalım akımı ve vurum süresi gibi farklı işleme koşullarında deneyler yapılmıştır. İşleme haznesi titreşimli (İHT-EEİ) deneylerde titreşimsiz koşullara göre elektrot aşınma hızı (EAH) ve bağıl aşınma (BA) değerleri azalmıştır. Deneysel sonuçlara göre işleme haznesine uygulanan titreşimler elektrot köşe yarıçap değerlerinde azalmaya neden olmuştur.