JLJianfeng Li

Jianfeng Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jianfeng Li has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Study on Nb APC Nb-Ti Superconductor Made by Powder Metallurgy

    by Lingxiao Yan, Qiang Guo, Bin Tang, Ruilong Wang, Kailin Zhang, Zijing Zhou, Xianghong Liu, Yong Feng, Jianfeng Li, Pingxiang Zhang

    The incorporation of Artificial Pinning Centers (APC) into Nb-Ti superconductors has been demonstrated as an effective method for enhancing their performance. Typically, APC Nb-Ti superconductors are fabricated using the Powder-Metallurgy technique, which involves the utilization of fine Nb-Ti powder and APC powder as precursors. The efficacy of APCs is largely determined by their size, quantity, and distribution, which are crucial factors influencing the Critical Current Density ( Jc ) of APC Nb-Ti superconductors. In this study, various batches of Nb-Ti and Nb powder with particle sizes ranging from 15 to 150 microns and different ratios were employed to produce APC Nb-Ti superconductors. We explored the influence of Nb particle size and shape on the superconducting properties and microstructure of APC Nb-Ti superconductors. Experimental findings indicate that Nb-APC Nb-Ti superconductors exhibit enhanced Critical Current Density at lower magnetic fields. Furthermore, reducing the processing strain notably improves the Critical Current Density. The Critical Current Density of Nb-APC Nb-Ti superconductors reached 7730 A/mm 2 at 2T, following a heat treatment of 400 °C for 20 hours, repeated three times, and utilizing Nb powder with sizes between 50 and 150 μm.

  • Study on High Yield Strength Monolith NbTi Superconducting Wire for MRI Magnets in WST

    by Zhang Kailin, Guo Qiang, Jiang Longtao, Han Luyang, Zhao Jiajun, Li Hengchao, Xianghong Liu, Yong Feng, Li Jian Feng, Zhang Pingxiang

    NbTi strands are widely used in magnetic resonance imaging (MRI) and other superconducting magnets for their good processing characteristics, low cost, and good superconducting performance. With the huge demand for high yield strength monolith wire for MRI using less liquid helium, improving the yield strength of monolith NbTi wire becomes a problem that urgently needs to be solved. In this study, we adopted a new fabrication process by “enameling insulation before rolling and forming” to improve the yield strength of the wire. By choosing the suitable insulation material and adjusting the working rate, the insulation property has been improved. The results show that the polyvinyl formal (PVF) is the best material for the “rolling and forming” process and the fact also shows that the working rate should be controlled between 15% to 25%. The final monolith NbTi wires show good insulation performance, while the forming size is controlled within ± 0.003 mm and the average value of 0.1% yield strength increases from ∼120 MPa to ∼350 MPa.


  • Fabrication of Low AC Loss Cu0.5Mn-Based NbTi Superconducting Strands

    by Qiang Guo, Ruilong Wang, Kailin Zhang, Yanmin Zhu, Jianfeng Li, Xianghong Liu, Yong Feng

    The Cu-0.5 wt.% Mn alloy is selected as the inter-filament matrix in NbTi superconducting strand with low AC Loss. Three types of NbTi strand with the filament number of 10800,12960 and 33696 were prepared based on high homogeneity Nb47Ti alloy,pure Nb sheet,high purity oxygen free copper and Cu-0.5 wt.% Mn alloy. Heat treatment with 3-5 intermediate annealings has been applied to increase the Jc of the strands. When the number of annealings increases from 3 to 5,Jc raises from 2295 to 2958 A/mm2 for the 10800 filament strand,and from ~2500 to ~2800 A/mm2 for the 12960 filament and 33696 filament strands. As the filament number increases from 10800 to 33696,the n values keep the same level,demonstrating that no "sausage like" or "nodular like" filaments exist in the final strands. When the filament diameter of the strand reduces from 4.6 m to 2.6 m,the hysteresis loss decrease from 42.8 mJ/cm3 to 17.3 mJ/cm3 at 3 T&4.2 K. Based on this research,WST has obtained the stable mass production technology of the strands. Using heat treatment with 4 annealings,the different batches of the strands with Jc ranged from 2600 to 2800 A/mm2 have been produced with piece length level of 1-3 kilometer.


  • Effect of Nb3Sn Coarse Grains on Critical Current Densities of Internal Tin Nb3Sn Strand

    by Bo Wu, Guo Yan, Jianfeng Li, Pingxiang Zhang, Jinshan Li, Yigong Shi, Jianya Chen, Shaolin Wang, Ke Zhang, Qiang Guo, et al.

    $\text{Nb}_3 Sn$ strands have significant applications in constructing high-field (> 10 T) magnets and have great potential value in the next 20 years. Internal-tin (IT) $\text{Nb}_3 Sn$ strand has been developed by many methods for the future fusion reactor after ITER with low hysteresis loss. However, how to improve the current densities of $\text{Nb}_3 Sn$ strand has become very important with the increasing demand for high Jc $\text{Nb}_3 Sn$ strand. In our study, we found that more than double Nb content should be added within Internal Tin $\text{Nb}_3 Sn$ strand and 2 times critical current densities can be enhanced compared with ITER $\text{Nb}_3 Sn$ strand. With this $\text{Nb}_3 Sn$ strand, the phase transition during heat treatment was investigated and new phase (Cu-Nb-Sn) can be formed at 400°C due to higher ratio of Sn/Cu and more Cu6Sn5 phase decomposition. The coarse $\text{Nb}_3 Sn$ grains were analyzed and a composite structure (Cu and $\text{Nb}_3 Sn$ ) can be formed as Nb element diffusion during Cu-Nb-Sn phase formation. We also found that phase-balance (less Cu-Nb-Sn produced), which can control the formation of $\text{Nb}_3 Sn$ coarse during filaments, can be obtained through element ratio optimization. With this method, coarse grains among filaments can be refined from micron size into nano-size. Effect of varisized coarse grains on the critical current densities was also studied and we found that micron sized $\text{Nb}_3 Sn$ (1∼2μm) grains reduced the critical current densities severely.


  • Status of Internal-Tin Nb3Sn Strand for Divertor Tokamak Test Facility

    by Jianwei Liu, Yigong Shi, Bo Wu, Ke Zhang, Sheng Liu, Jianfeng Li, Xianghong Liu, Yong Feng, Pingxiang Zhang

    Divertor Tokamak Test facility (DTT) is going to be built in Italy, and is expected to be operated along with ITER to explore the potential solution for the power exhaust to be eventually implemented in DEMO. 77 tons of Nb3Sn strand in two types are required by DTT. For type one, the weight is 55 tons. The dominant performance requirements are $I_c >285$ A (4.2 K, 12 T) and hysteresis loss $< 1000 mJ/cm^3$ ( $4.2 K, \pm 3 T$ ). For type two, the weight is 22 tons. The dominant performance requirements are $I_c > 260\;A (4.2\;K, 12\;T)$ and hysteresis loss $< 400 mJ/cm^3 (4.2\;K, \pm 3\;T)$ . These performance requirements are quite challenging in the respect of performance stability in Nb3Sn strand production. WST has successfully developed three types of Nb3Sn strand to meet these requirements especially for DTT. For DTT type one, considering the ultra-high level of Ic, Nb and Sn volume was increased based on the structure of WST Nb3Sn strand for ITER. $I_c > 300\;A (4.2\;K, 12\;T)$ and hysteresis loss $< 700 mJ/cm^3 (4.2\;K, \pm 3\;T)$ have been obtained from both 164-filament structure and larger-filament structure. For DTT type two, Cu split structure was selected to guarantee low hysteresis level. For the structure with 160 filaments and one Cu split, $I_c > 260\;A (4.2\;K, 12\;T)$ and hysteresis loss $< 400 mJ/cm^3 (4.2\;K, \pm 3\;T)$ have been achieved. Finally, all the performance of DTT Nb3Sn strand has been accomplished by WST.


  • Ongoing Efforts at Internal-Tin Nb3Sn Strand With Higher Jcn and Lower Hysteresis Loss

    by Jianwei Liu, Yigong Shi, Bo Wu, Ke Zhang, Jianfeng Li, Xianghong Liu, Yong Feng, Pingxiang Zhang

    WST has been keeping in the research and development of internal-tin (IT) Nb3Sn strand for higher performance level, for the future fusion reactor after ITER. Deformation optimization, Cu splits and Sn spacers were applied to prepare Nb3Sn strand with higher Jcn and lower hysteresis loss, and effect of these three factors on performance was investigated and discussed. Compared with the Nb3Sn strand for ITER, strand distortion was obviously reduced by deformation optimization and Jcn was improved, but at the same time hysteresis level was increased. To reduce the level of hysteresis loss, Cu splits were used to replace a few Nb filaments in each subelement. Cu splits could break the bridging Nb3Sn filament rings and as a sequence hysteresis loss was dramatically reduced along with the reduction of Jcn, which is attributed to low reaction degree of Nb filaments in the outermost subelements. Therefore, Sn spacers between the outermost subelements and the Ta barrier were added, and a 37-subelement structure was used to shorten the diffusion path of Sn. Reaction degree of the filaments was enhanced as well as Jcn. Finally, it could be concluded that 37-subelement structure with Cu splits is effective to reduce the level of hysteresis loss and raise the level of Jcn.


  • Enhanced Critical Current Densities in Nb3Sn Superconducting Strands Prepared by Bronze Process

    by Zhang Ke, Qin Xing, Hou Jing, Wu Bo, Gao Huixian, Liu Jianwei, Li Jianfeng, Zhang Pingxiang, Liu Xianghong, Feng Yong

    In the development of Nb$_{3}$Sn superconducting strands, the improvement of the non-Cu critical current density (${Jc}$) has been greatly emphasized. Different Nb$_{3}$Sn strands were manufactured by the bronze route artificially doped with titanium in bronze. The influences of bronze on Nb volume ratio, filament material, filament diameter, and heat treatment were studied. In this research, Bronze to Nb volume ratio affected ${Jc}$ slightly due to the formation of the Sn shortage and similar Nb$_{3}$Sn volume after heat treatment. The study of filament diameter indicates that ${Jc}$ increases largely as the filament diameter reduces for the full reaction. Different heat treatment times at 575 °C, 650 °C, and 675 °C will result in various performances. According to microstructure images, residual Nb core can be seen in each filament. Bigger average grain size will lead to lower ${Jc}$.