Andreas Vetter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andreas Vetter has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Bernhard Hofbeck
ZAE Bayern, 91058, Erlangen Germany
1 shared publication - Christian Camus
LayTec AG, Berlin, Germany
1 shared publication - Christoph Joseph Brabec
Institute of Materials for Electronics and Energy Technology (i‐MEET) Department of Materials Science and Engineering Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Erlangen Germany
1 shared publication - Jens Hauch
Department of High Throughput Methods in Photovoltaics Forschungszentrum Jülich GmbH Helmholtz-Institute Erlangen-Nürnberg (HI ERN) Immerwahrstraße 2 91058 Erlangen Germany
1 shared publication - Johannes Hepp
Institute of Materials for Electronics and Energy (i‐MEET) Friedrich Alexander University Erlangen‐Nuremberg Erlangen Germany
1 shared publication - Umair Sultan
Institute of Particle Technology Department of Chemical and Biological Engineering Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Cauerstrasse 4 91058 Erlangen Germany
1 shared publication
Latest Publications
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 10 (3) , 898-904
Quantitative Analysis of the Separate Influences of Material Composition and Local Defects on theVocof PV Devices: An Exemplary Study on CIGS
A lot of effort is required in order to close the efficiency gap between laboratory record Cu(In,Ga)Se $_{2}$ (CIGS) solar cells and commercially produced modules. An obstacle easily overlooked is the fact that reduced module performance may have multiple root causes. Here, we show how to isolate two main factors that influence the open circuit voltage (V $_\text{oc}$ ) of photovoltaic devices, the material composition and the local defects, here shunts in particular, i.e., regions of significantly lowered resistivity. In order to characterize the material composition, we used electroluminescence spectroscopy. Additionally, we investigated the effect of local defects on the V $_\text{oc}$ , by the use of thermography. Which of both factors dominates the resulting V $_\text{oc}$ depends on the insolation intensity under which the device is operated. We established a model in order to estimate the V $_\text{oc}$ as a function of the luminescence peak wavelength, the quantification of the thermal hot spots caused by local defects, and the insolation intensity. Subsequently, we investigated how these factors affect the electrical conversion efficiency of the device. The combination of these two measurement techniques results in a more conclusive evaluation of the electrical parameters, thereby enabling an improved quality assessment to allow a successive process optimization. This approach is also applicable to other thin film PV technologies such as perovskite and organic solar cells.- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 10 (3) , 898-904
Quantitative Analysis of the Separate Influences of Material Composition and Local Defects on theVocof PV Devices: An Exemplary Study on CIGS
A lot of effort is required in order to close the efficiency gap between laboratory record Cu(In,Ga)Se $_{2}$ (CIGS) solar cells and commercially produced modules. An obstacle easily overlooked is the fact that reduced module performance may have multiple root causes. Here, we show how to isolate two main factors that influence the open circuit voltage (V $_\text{oc}$ ) of photovoltaic devices, the material composition and the local defects, here shunts in particular, i.e., regions of significantly lowered resistivity. In order to characterize the material composition, we used electroluminescence spectroscopy. Additionally, we investigated the effect of local defects on the V $_\text{oc}$ , by the use of thermography. Which of both factors dominates the resulting V $_\text{oc}$ depends on the insolation intensity under which the device is operated. We established a model in order to estimate the V $_\text{oc}$ as a function of the luminescence peak wavelength, the quantification of the thermal hot spots caused by local defects, and the insolation intensity. Subsequently, we investigated how these factors affect the electrical conversion efficiency of the device. The combination of these two measurement techniques results in a more conclusive evaluation of the electrical parameters, thereby enabling an improved quality assessment to allow a successive process optimization. This approach is also applicable to other thin film PV technologies such as perovskite and organic solar cells.