Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Prateek Deoman Malwe has a total of 142 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermal Response of LiFePO4 Pouch Cells Under Dynamic Drive Cycles: Effects of Ambient Temperature and Battery Pack Size

    by Pravin A. Mane, Karthik Balasubramanian, Sampath K. Chinige, Prateek D. Malwe

    Low-power electric vehicles are expanding rapidly in India, where ambient temperatures of 35–40 °C are common, yet experimental data on large-format LiFePO4 (LFP) cells under realistic drive-cycle loading in such climates are scarce. A 20 Ah LFP pouch cell was loaded with cell-level power profiles derived from the IUDC, WLTC Class 1 and WLTC Class 2 cycles for packs of 16–80 cells (≈1–5 kWh) at ambient temperatures of 25–40 °C, under natural convection and forced air at 3 m/s. The results were assessed against a thermal-management target (≤35 °C and surface temperature difference ≤5 °C) and the manufacturer’s upper operating limit (55 °C). Under natural convection, the temperature rise above ambient fell from 11.5–17.5 °C for the 1 kWh pack to ≤4.5 °C for the 4 and 5 kWh packs, consistent with the inverse scaling of cell current with cell count. The target was met under all cycles only by the 4 and 5 kWh packs at ≤30 °C; at 35–40 °C, no ambient-air strategy can meet it. At 40 °C, the 1 kWh pack reached 55.3–57.5 °C under WLTC loading. Forced air reduced the temperature rise by 28–41% at 25 °C but by only 4–20% at 40 °C; it kept the 2 kWh pack at least 7.9 °C below the limit, but not the 1 kWh pack under WLTC Class 2 at 40 °C. The resulting operating envelope supports pack sizing and thermal management of low-power electric vehicles in hot climates.

  • Open Access

    Enhancement of critical heat flux and heat transfer during jet impingement quenching using Al2O3 and SiO2 nanofluids

    by Vivek Gupta, Prerna Mishra, Prateek D. Malwe, Pravin A. Mane, Uttam Jadhav, Rohit Kumar Singh Gautam, Komal Jahagirdar, Choon Kit Chan, Chandrakant Sonawane, Satish Kumar

  • Open Access

    RLE-Based Model Predictive Control vs. Rule-Based Control for Energy Management in Multi-Architecture Electric Vehicles

    by Digvijay Kanase, Arun Thorat, Pravin Mane, Prateek D. Malwe, Pramod Magade, Choon Kit Chan, Subhav Singh, Deekshant Varshney

    Energy management is a key factor in the range, safety and battery life of electrified vehicles. In this study, a Recursive Least Squares (RLS)-augmented Model Predictive Control (MPC) framework is designed and validated for real-time energy management of four different EV powertrain architectures: Battery Electric Vehicle (BEV), Battery-Supercapacitor Hybrid, Battery-Flywheel Hybrid, and Battery-ICE Hybrid. The architecture is built in MATLAB/Simulink R2022b; an RLS subsystem is used to adapt in real time the battery impedance parameters. Representative multi-regime drive cycles were used to evaluate all eight quantitative metrics of performance. RLS-MPC constantly outperformed the rule-based control for all the architectures. The velocity tracking RMSE was reduced by 10.4% (BEV), 14.9% (Supercapacitor), and 13.9% (ICE Hybrid). Energy use was lowered for BEV (−4.5%) and Supercapacitor (−3.7%) architectures, and auxiliary energy use was shown to be greater for hybrid architectures: +61.5% (Supercapacitor), +430.6% (Flywheel), and +73.7% (ICE Hybrid), with auxiliary storage pre-positioned in advance of an expected deceleration. The Supercapacitor-MPC configuration was able to operate with a near-zero net battery draw (+0.006 kWh) compared to the baseline. Flywheel-MPC had a final state-of-charge of 84.7% (when including conversion losses, this was not yet energy neutral, but close). The vectorized MATLAB implementation required less than 30 μs to compute one step; the projected embedded execution time on automotive microcontroller hardware is estimated to be between 20–40 ms, consistent with the 100 ms sampling budget. RLS-MPC has great promise for future use with next-generation electrified powertrains, and future work will focus on embeddability.

  • Open Access

    Natural convection heat transfer performance of finned heat sinks with different fin materials and geometries

    by Sawan Wani, Sachin Shinde, Prateek D. Malwe, Choon Kit Chan, Chandrakant Sonawane

    Effective thermal management of electronic devices using passive cooling is a significant engineering challenge. This experimental study looks at how fin material and design affect the natural convection heat transfer of heat sinks attached to a vertical aluminum plate. Four configurations were tested under steady-state conditions: a flat plate, plates with horizontal aluminium fins, vertical aluminium fins, and copper fins arranged in a V-shape. The experiments covered heater input powers from 25 to 150 W, and we measured surface temperatures with calibrated K-type thermocouples. We calculated the heat transfer coefficient, Nusselt number, and the difference between surface and ambient temperatures to assess thermal performance. This experimental study systematically investigates the influence of fin geometry and material on natural convection heat transfer from a vertically heated aluminium plate under identical steady-state conditions. Three fin materials (aluminium, copper, and brass) and three configurations (vertical, horizontal, and V-shaped fins) were examined over a heater input range of 25–150 W. Surface temperatures were measured using calibrated K-type thermocouples (± 0.5 °C accuracy). The heat transfer coefficient, Nusselt number, enhancement ratio, and thermal resistance were calculated using energy balance relations. The copper V-fin configuration achieved a maximum heat transfer coefficient of 47.66 W/m2 K at 150 W, representing a 30–40% enhancement compared to the plain plate. Surface temperature reduction reached 15–20% depending on heat input. All results are supported by quantitative uncertainty analysis (± 6–8%).These findings provide experimentally validated guidance for the optimization of passive natural convection heat sinks.


  • Open Access

    Efficiency, cost, and carbon footprint considerations in analysing hybrid solar thermal-photovoltaic desalination systems

    by Rohan R. Pandit, Sandip S. Deshmukh, Krishna J. Khatod, Vikrant P. Katekar, Prateek D. Malwe, Choon Kit Chan, Feroz Shaik, L. Syam Sundar, Nithesh Naik


  • Open Access

    A Solar-Powered Automated Irrigation System Using Arduino and Moisture Sensors for Efficient Water Management in Agriculture

    by Choon Kit Chan, Prateek D. Malwe, Vinayak T. Mandlik, Naresh Jaiswal, Shivaji B. Jadhav, Narayan Sapkal, Narendra Bhopale, Chandrakant R. Sonawane, Subhav Singh, Deekshant Varshaney, et al.

    As agriculture is the primary source of food in many countries, effective irrigation systems are crucial. This article presents a system that can regulate irrigation based on demand using Arduino Uno, a solar-powered water pump, and an autonomous water flow control system with a moisture sensor to reduce water consumption and time. Traditional irrigation methods often lead to inefficient water use due to a lack of real-time monitoring and control, especially in regions with limited water resources. In addition, manual irrigation systems are time-consuming and can result in over- or under-irrigation, affecting crop yield and resource management. With increasing concerns about water scarcity and the need for sustainable agriculture, there is a critical need for automated irrigation solutions that are both energy-efficient and cost-effective. The proposed system aims to optimize water usage based on soil conditions in real time. This system can be applied to farms, parks, and other locations that require efficient irrigation systems. The proposed approach supports aggressive water management for agricultural land, reduces power costs, is cheap, has a small size, and is highly adaptable. This system is especially beneficial for farmers and gardeners who may not have the time or resources for regular irrigation. Assessing real-time soil moisture levels can ensure that crops receive optimal water supply based on actual needs.


  • Open Access

    Ratcheting fatigue behaviour of advanced structural materials at their service temperatures

    by Prerna Mishra, Vivek Gupta, Prateek Deoman Malwe, Ashish Urade, Venushree Khanke, Irfanul Haque Siddiqui, Saurav Dixit, Choon Kit Chan, Chandrakant Sonawane, Ghanshyam G. Tejani

    Ratcheting fatigue behavior is a critical phenomenon in structural materials undergoing cyclic loading, particularly when combined with nonzero mean stress or multiaxial stress states. This manifests as the progressive buildup of plastic strain in one direction with each loading cycle, ultimately leading to material degradation and failure. This behavior is highly relevant in industries such as automotive, aerospace, nuclear, and civil engineering, where components frequently experience complex loading conditions. Structural materials exposed to ratcheting fatigue often exhibit changes in their mechanical properties, such as cyclic hardening or softening, which influence their ability to withstand cyclic stresses. Factors such as the mean stress, stress amplitude, loading path, material microstructure, and environmental conditions play crucial roles in governing the ratcheting response. Understanding the ratcheting fatigue behavior is essential for the design and life prediction of critical components. Comprehensive investigations through experimental testing and computational modelling are required. This investigation presents the asymmetrical stress-controlled (ratcheting) behaviour of 9 C-1Mo modified steel and IN-617 superalloy at service temperatures of 600 and 800oC respectively at different tensile mean stresses. When there was change in the mean stress, the amplitude of stress as well as the rate of stress was not changed. The fatigue life of these alloys decreased with an increase in tensile mean stress. The maximum stress increases with the mean stress and leads to a higher inducement of the plastic strain, which results in a lower fatigue life. At elevated temperatures, the fatigue life was found to be higher than that at room temperature (RT) owing to dynamic-strain aging.


  • Open Access

    Performance investigation on Organic Rankine Cycle from a low-temperature heat source

    by Prateek D. Malwe, Bajirao S. Gawali, Avinash Salunke, Kamal Sharma, Ankur Salunkhe, Irfanul Haque Siddiqui, Bhavin Mehta, Ghanshyam Tejani


  • Open Access

    Effect of Sheet Thickness and Strength of Dual-Phase Steels (DP600, DP780, DP980) on the Quality of Roll-Formed U-Profiles

    by Dayanand P. Yesane, R. V. Bhortake, Prateek D. Malwe, Ashish D. Urade, Naresh Jaiswal, Choon Kit Chan, Subhav Singh, Deekshant Varshney, Arunkumar Bongale, B. T. Ramesh, et al.

    This study explores how material strength and sheet thickness impact residual stress, strain and defects in roll-formed U-sections.

  • Open Access

    Performance assessment of radiator using various combinations of nanofluids as coolant

    by Choon Kit Chan, Prateek D. Malwe, Prerana B. Jadhav, Nitin P. Bhone, Naresh Jaiswal, Ankit Oza, Ghanshyam Tejani, Feroz Shaik, Subhav Singh, Deekshant Varshney

    This study considers the effect of CuO (copper oxide) nanoparticles on the heat transfer performance of automotive radiators with imprint formulation while controlling the design of experiments and the factors affecting its performance. Other factors include the concentration of CuO nanoparticles, which is characterized by measuring actual thermal performance parameters such as thermal conductivity and pressure drop. The experimental design includes the configuration of the apparatus, the measuring devices and their arrangement, and the placement of thermometers and flow restrictors for efficient data collection. Externally controlled and monitored conditions include a non-restricted constant temperature space and minimal or no airflow to avoid inconsistencies in the gathered data. In this study it has been seen that with increased CuO concentrations where enhanced heat transfer was achieved, there was also a corresponding increase in flow resistance. This research justifies the need to design an appropriate experimental plan and control the measuring conditions to achieve the expected results with precision and reproducibility. This work contributes to this understanding and presents various possibilities for improving radiator performance using nanotechnology.