Masaaki Oshita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Masaaki Oshita has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Tetsuo Kan
Department of Mechanical and Intelligent Systems Engineering, Graduate School of Informatics and Engineering, The University of Electro-Communications, 1-5-1 Chofugaoka, Chofu, Tokyo 182-8585, Japan
7 shared publications Shiro Saito
IMRA Japan Company Ltd., Kariya, Aichi, Japan
3 shared publications- Eslam Abubakr
Department of Mechanical Engineering and Intelligent Systems, Graduate School of Informatics and Engineering, The University of Electro-Communications, Tokyo, Japan
2 shared publications Ashenafi Abadi
Department of Mechanical Engineering and Intelligent Systems, Graduate School of Informatics and Engineering, The University of Electro-Communications, Tokyo, Japan
1 shared publication- Ashenafi Abadi
Department of Mechanical Engineering and Intelligent Systems, Graduate School of Informatics and Engineering, The University of Electro-Communications, Tokyo, Japan
1 shared publication Ashenafi Elyas
1 shared publication
Latest Publications
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 301-305
Advanced Room-Temperature NIR Plasmonic Photodetection and Reconstructive Spectroscopy
While Au is commonly utilized in semiconductor fabrication, its interaction with Si yields unstable contacts, posing potential reliability concerns. In this work, Cr interlayers were integrated to improve interface properties, enhance charge carrier transport within a plasmonic photodetector, and ensure long-term stability, demonstrated by consistent responses under zero bias and room-temperature conditions over the span of a year. The induced Fermi level shifts and Schottky barrier lowering to 0.59 eV, improving responsivity and extending the operation range beyond 1850 nm with increased sensitivity, allowing for precise reconstructive spectroscopy (RS). This is promising for reliable compound identification based on specific bond absorbance properties while scaling down IR spectroscopy to chip level, promoting applications like environmental monitoring and gas detection.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 301-305
Advanced Room-Temperature NIR Plasmonic Photodetection and Reconstructive Spectroscopy
While Au is commonly utilized in semiconductor fabrication, its interaction with Si yields unstable contacts, posing potential reliability concerns. In this work, Cr interlayers were integrated to improve interface properties, enhance charge carrier transport within a plasmonic photodetector, and ensure long-term stability, demonstrated by consistent responses under zero bias and room-temperature conditions over the span of a year. The induced Fermi level shifts and Schottky barrier lowering to 0.59 eV, improving responsivity and extending the operation range beyond 1850 nm with increased sensitivity, allowing for precise reconstructive spectroscopy (RS). This is promising for reliable compound identification based on specific bond absorbance properties while scaling down IR spectroscopy to chip level, promoting applications like environmental monitoring and gas detection.
- 14 August 2024
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 183
Plasmonic photodetector with submicron grating for reconstructive spectroscopy of low-intensity broadband light
- 14 August 2024
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 183
Plasmonic photodetector with submicron grating for reconstructive spectroscopy of low-intensity broadband light
- 4 March 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (8) , 2046-2055
Characterization of an uncooled mid-infrared Schottky photodetector based on a 2D Au/PtSi/p-Si nanohole array at a higher light modulation frequency
In this study, an uncooled 2D nanohole array PtSi/p-Si Schottky mid-infrared (MIR) photodetector, which is essential for on-chip Si-based low-barrier MIR detectors, is presented. Room temperature operation introduces susceptibility to thermal noise and can impact stability. Through modulation frequency and reverse bias optimization, the stability improved by 7 times at 170 Hz and −3.5V, respectively. The effective light detection and stability were confirmed through ON/OFF response measurements over a longer time. The wavelength-dependent responsivity, measured with a tunable MIR laser, confirmed the responsiveness of the device in the MIR region of 2.5 µm to 4.0 µm, with a maximum specific detectivity (D*) of 2.0×103cmHz1/2W−1 at 3.0 µm; this result shows its potential applicability for noninvasive human lipid monitoring. Overall, this study focuses on the crucial role of signal analysis optimization in enhancing the performance of MIR photodetectors at room temperature.
- 4 March 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (8) , 2046-2055
Characterization of an uncooled mid-infrared Schottky photodetector based on a 2D Au/PtSi/p-Si nanohole array at a higher light modulation frequency
In this study, an uncooled 2D nanohole array PtSi/p-Si Schottky mid-infrared (MIR) photodetector, which is essential for on-chip Si-based low-barrier MIR detectors, is presented. Room temperature operation introduces susceptibility to thermal noise and can impact stability. Through modulation frequency and reverse bias optimization, the stability improved by 7 times at 170 Hz and −3.5V, respectively. The effective light detection and stability were confirmed through ON/OFF response measurements over a longer time. The wavelength-dependent responsivity, measured with a tunable MIR laser, confirmed the responsiveness of the device in the MIR region of 2.5 µm to 4.0 µm, with a maximum specific detectivity (D*) of 2.0×103cmHz1/2W−1 at 3.0 µm; this result shows its potential applicability for noninvasive human lipid monitoring. Overall, this study focuses on the crucial role of signal analysis optimization in enhancing the performance of MIR photodetectors at room temperature.
- Open Access
- 1 November 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (11)
Detection of backside coupled propagating surface plasmon resonance on the sidewall of a wafer
We proposed a surface plasmon resonance (SPR) sensor structure that utilized a glass wafer with a diffraction grating and an n-type silicon piece bonded near the SPR coupling site. This configuration enabled surface plasmon excitation from the back of the substrate without the unwanted interaction between the excitation light and the sample, and electrical detection of the SPR response by a 0.7-eV Schottky barrier at the Au/n-Si interface formed on the sidewall of the silicon piece was achieved. Experimental evaluation of the surface plasmon coupling performance was conducted, showing clear peaks in the photocurrent for various wavelengths in the NIR-II window, ranging from 1100 to 1300 nm. The device’s ability to detect propagating surface plasmons as a photocurrent was confirmed; the results indicated a consistent trend with theoretical and numerical calculations. Since the device was composed of a glass substrate, the use of wavelengths shorter than the near-infrared wavelength was possible, including visible wavelengths where the optical absorption by water is negligible. Thus, our proposed sensor provides a compact and efficient solution for SPR sensing in aqueous solutions.
- 1 November 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (11)
Open AccessDetection of backside coupled propagating surface plasmon resonance on the sidewall of a wafer
We proposed a surface plasmon resonance (SPR) sensor structure that utilized a glass wafer with a diffraction grating and an n-type silicon piece bonded near the SPR coupling site. This configuration enabled surface plasmon excitation from the back of the substrate without the unwanted interaction between the excitation light and the sample, and electrical detection of the SPR response by a 0.7-eV Schottky barrier at the Au/n-Si interface formed on the sidewall of the silicon piece was achieved. Experimental evaluation of the surface plasmon coupling performance was conducted, showing clear peaks in the photocurrent for various wavelengths in the NIR-II window, ranging from 1100 to 1300 nm. The device’s ability to detect propagating surface plasmons as a photocurrent was confirmed; the results indicated a consistent trend with theoretical and numerical calculations. Since the device was composed of a glass substrate, the use of wavelengths shorter than the near-infrared wavelength was possible, including visible wavelengths where the optical absorption by water is negligible. Thus, our proposed sensor provides a compact and efficient solution for SPR sensing in aqueous solutions.
- Open Access
- 9 March 2023
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 9 (1) , 1-8
Electromechanically reconfigurable plasmonic photodetector with a distinct shift in resonant wavelength
Plasmonic photodetectors have received increasing attention because their detection properties can be designed by tailoring their metal structures on surfaces without using any additional components. Reconfiguration of the plasmonic resonant state in a photodetector is relevant for various applications, including investigating in situ adaptive detection property changes, depending on the situation, and performing single-pixel spectroscopy in geometrically limited regions. However, the spectral responsivity change with conventional reconfiguration methods is relatively small. Here, we propose a plasmonic photodetector that reconfigures its spectral responsivity with electromechanical deformation instead of bias tuning. The photodetector consists of a gold plasmonic grating formed on an n-type silicon cantilever, and the spectral responsivity is reconfigured by electromechanically scanning at an incident angle to the grating on the cantilever. The photodetector exhibits peak shifts in spectral responsivity in a wavelength range from 1250 to 1310 nm after electromechanical reconfiguration. Finally, for potential future applications, we demonstrate near-infrared spectroscopy using the photodetector. This photodetector has the potential to be adopted as a near-infrared spectrometer in industrial silicon imaging systems because its structure enables subbandgap photodetection on silicon by a Schottky junction.
- 9 March 2023
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 9 (1) , 1-8
Open AccessElectromechanically reconfigurable plasmonic photodetector with a distinct shift in resonant wavelength
Plasmonic photodetectors have received increasing attention because their detection properties can be designed by tailoring their metal structures on surfaces without using any additional components. Reconfiguration of the plasmonic resonant state in a photodetector is relevant for various applications, including investigating in situ adaptive detection property changes, depending on the situation, and performing single-pixel spectroscopy in geometrically limited regions. However, the spectral responsivity change with conventional reconfiguration methods is relatively small. Here, we propose a plasmonic photodetector that reconfigures its spectral responsivity with electromechanical deformation instead of bias tuning. The photodetector consists of a gold plasmonic grating formed on an n-type silicon cantilever, and the spectral responsivity is reconfigured by electromechanically scanning at an incident angle to the grating on the cantilever. The photodetector exhibits peak shifts in spectral responsivity in a wavelength range from 1250 to 1310 nm after electromechanical reconfiguration. Finally, for potential future applications, we demonstrate near-infrared spectroscopy using the photodetector. This photodetector has the potential to be adopted as a near-infrared spectrometer in industrial silicon imaging systems because its structure enables subbandgap photodetection on silicon by a Schottky junction.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (23) , 22557-22563
Grating-Based Surface Plasmon Resonance Sensor for Visible Light Employing a Metal/Semiconductor Junction for Electrical Readout
In this study, we proposed an electrical readout surface plasmon resonance (SPR) chemical sensor coupled with visible light to avoid significant light absorption of water. A gold (Au) diffraction grating with a submicron pitch, designed using the rigorous coupled-wave analysis method to have a submicron pitch and 30-nm-tall Au grating, was fabricated on an n-type silicon (n-Si) substrate by nano/microfabrication. The hot electrons generated by SPR on the grating are converted to photocurrent at the Schottky barrier at the Au/n-Si interface. The Schottky barrier height was estimated based on I-V characteristics of the device to be q Φ B = 0.72 eV. The peak shift of photocurrent was observed to be consistent with the surface plasmon resonance theory when the concentration of glucose aqueous solution changed the refractive index on the Au grating. Assuming that the incident wavelength and angle were fixed, noise analysis revealed a refractive index resolution of 3.4–4.0 × 10 -5 RIU. Since this structure eliminated bulky optics in SPR experiments, it would contribute to the realization of a thin single-chip label-free chemical sensor.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (23) , 22557-22563
Grating-Based Surface Plasmon Resonance Sensor for Visible Light Employing a Metal/Semiconductor Junction for Electrical Readout
In this study, we proposed an electrical readout surface plasmon resonance (SPR) chemical sensor coupled with visible light to avoid significant light absorption of water. A gold (Au) diffraction grating with a submicron pitch, designed using the rigorous coupled-wave analysis method to have a submicron pitch and 30-nm-tall Au grating, was fabricated on an n-type silicon (n-Si) substrate by nano/microfabrication. The hot electrons generated by SPR on the grating are converted to photocurrent at the Schottky barrier at the Au/n-Si interface. The Schottky barrier height was estimated based on I-V characteristics of the device to be q Φ B = 0.72 eV. The peak shift of photocurrent was observed to be consistent with the surface plasmon resonance theory when the concentration of glucose aqueous solution changed the refractive index on the Au grating. Assuming that the incident wavelength and angle were fixed, noise analysis revealed a refractive index resolution of 3.4–4.0 × 10 -5 RIU. Since this structure eliminated bulky optics in SPR experiments, it would contribute to the realization of a thin single-chip label-free chemical sensor.
- 9 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 959-962
Reconfigurable Plasmonic Photodetector Integrated with Electrostatic Actuator For Spectrometry
Miniaturized spectrometers enable spectrometry on limited space, and they have been actively studied for various applications. Although various methods have been proposed to miniaturize spectrometer, conventional spectrometer consist of multiple filters and photodetectors, which limits the reduction of the footprint. Here, we report a reconfigurable plasmonic photodetector integrated with electrostatic actuator for spectrometry. In this paper, we investigated whether spectroscopy is possible using this structure in wavelength range from 1240 nm to 1310 nm. The simplicity of this structure presents potential to be adapted in micro-spectrometers.
- 9 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 959-962
Reconfigurable Plasmonic Photodetector Integrated with Electrostatic Actuator For Spectrometry
Miniaturized spectrometers enable spectrometry on limited space, and they have been actively studied for various applications. Although various methods have been proposed to miniaturize spectrometer, conventional spectrometer consist of multiple filters and photodetectors, which limits the reduction of the footprint. Here, we report a reconfigurable plasmonic photodetector integrated with electrostatic actuator for spectrometry. In this paper, we investigated whether spectroscopy is possible using this structure in wavelength range from 1240 nm to 1310 nm. The simplicity of this structure presents potential to be adapted in micro-spectrometers.