GGGamze Gumuslu Gur

Gamze Gumuslu Gur

*This is an algorithmically generated author record based on publicly available information.

Gamze Gumuslu Gur has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Ni-based Catalysts Supported on SCS–Derived MgAl2O4 for CO2 Methanation: Effect of Bimetallic Promoters

    by Duygu Yeşiltepe-Özçelik, Utku Burgun, Emircan Uysal, Gamze Gümüşlü-Gür, Alper Sarıoğlan, Sebahattin Gürmen

    In this study, Ni-based catalysts (Ni, NiFe, and NiCo) were synthesized via wet impregnation method using MgAl 2 O 4 spinel supports calcined at 700, 800, and 900 °C. These supports, previously synthesized and optimized by the solution combustion method, enabled investigation of thermal treatment and bimetallic promotion affect catalytic performance in CO 2 methanation. Structural, morphological, and redox properties were characterized using XRD, BET, FT-IR, SEM-EDS, TEM, H 2 -TPR, CO 2 -TPD, and TGA analyses. Catalytic activity tests under atmospheric pressure revealed that the NiCo catalyst supported on MgAl 2 O 4 calcined at 800 °C exhibited the highest CO 2 conversion and CH 4 selectivity. This enhancement was attributed to improved metal dispersion, stronger metal–support interaction, and synergistic effects between Ni and Co species. These results demonstrate dual impact of support calcination temperature and bimetallic design on methanation efficiency. This work offers valuable insight into the rational design of thermally stable and highly active Ni-based catalysts for efficient CO 2 utilization in methane production. Graphical Abstract

  • Open Access

    Synthesis of MgAl2O4 by sol-gel method and investigation of catalytic performances in CO2 methanation

    by Duygu Yeşiltepe-Özçelik, Utku Burgun, Faruk Kaya, Emircan Uysal, Bora Derin, Andreas Schaefer, Per-Anders Carlsson, Gamze Gümüşlü-Gür, Alper Sarıoğlan, Sebahattin Gürmen

    CO2 levels in the atmosphere are increasing as a result of human activities such as industrial activities, fossil fuel usage, and deforestation. The CO2 methanation reaction, which converts CO2 into methane, may play a crucial role in addressing this issue. Like most commercial syntheses, the CO2 methanation process requires a catalyst. Spinel catalysts, particularly magnesium aluminate (MgAl2O4), have gained attention for their potential in CO2 methanation. In this study, MgAl2O4 nanoparticles were synthesized using a sol–gel method with a molar ratio of Mg:Al = 1:2, and calcined at temperatures ranging from 700 to 900 °C. The structural properties of the nanoparticles were characterized using differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller analysis, X-ray diffraction, field emission scanning electron microscopy, energy dispersive X-ray spectroscopy, and transmission electron microscopy. The results showed that the particles had nearly spherical morphology, with agglomeration occurring at higher temperatures. The surface area decreased with increasing calcination temperature, from 188 m²/g at 700 °C to 94 m²/g at 900 °C. NiCo-MgAl2O4 catalysts were prepared by impregnation and characterized by CO2 temperature-programmed desorption and hydrogen temperature-programmed reduction. Catalytic performance tests revealed that the NiCo-MgAl2O4 catalyst calcined at 800 °C achieved the highest CO2 conversion (~85%) and methane selectivity. Spent catalyst analysis showed that carbon deposition negatively affected catalyst performance over time. This study emphasizes the role of strong basic sites in CO2 activation and methane formation, suggesting future improvements in catalyst stability. Graphical Abstract


  • ZIF‐67 based nano sized-cobalt oxides via pyrolysis and cold plasma treatments for Fischer–Tropsch synthesis

    by Alper Sarıoğlan, Sogand Aghamohammadi, Yasemin Fatih Aghdaei, Mohsen Mohseni, Utku Burgun, Sahar Rezaei, Yavuz Aydemir, Sajjad Abbasi, Serife Sarioglan, Alireza Hosseinzadeh, et al.


  • Open Access

    Optimized intermediate layer formation and electroless plating methods to obtain supported dense Pd surfaces

    by Gamze Gümüşlü Gür, Berna Toprak

    Dense metallic membranes, especially Pd and Pd alloys, have been intensely investigated to provide an alternative and economical way to obtain H2 with ultrahigh purity. To overcome the high cost of Pd, composite membrane structures that comprise a thin layer of Pd are utilized. However, it is a challenge to obtain a thin, dense, and uniform Pd layer on the support materials. This study investigates the parametric analysis of γ-Al2O3 interlayer formation and the electroless Pd plating (Pd ELP) procedures on α-Al2O3 supports with the aim to achieve a thin, uniform Pd surface without annealing. Adjustments in PEG/PVA concentration, dipping time, and heat treatment enabled creating a thin γ-Al2O3 interlayer on α-Al2O3, minimizing pore size and density. Hydrazine concentration, heat treatment, and bath temperature were adjusted to optimize Pd ELP to achieve maximum yield from the plating bath and a dense, uniform surface without annealing. Pd/γ-Al2O3/α-Al2O3 structures were analyzed using scanning electron microscopy, X-ray diffraction, and thermogravimetric analysis to observe the impact of varied parameters on surface structures. Optimized sample was compared to an annealed Pd/α-Al2O3 prepared in accordance with literature methods and a Pd/graphite/α-Al2O3 sample to validate the use of optimized ELP procedure and the γ-Al2O3 interlayer. Results show that a dense and uniform 13 μm Pd coating was achieved on a γ-Al2O3-coated α-Al2O3 support without annealing, using three fresh ELP baths. This was done using sequential hydrazine addition with a decreased concentration (1 M) into the ELP baths at 30 °C, and applying heat treatment at 120 °C between each fresh ELP bath.


  • Open Access

    Effects of Rare Earth Metal Promotion over Zeolite-Supported Fe–Cu-Based Catalysts on the Light Olefin Production Performance in Fischer–Tropsch Synthesis

    by Utku Burgun, Hadi R. Zonouz, Hasancan Okutan, Hüsnü Atakül, Selim Senkan, Alper Sarioglan, Gamze Gumuslu Gur

    Fischer-Tropsch synthesis (FTS), a significant reaction for effective H2 utilization, is a promising approach for direct production of light olefins from syngas (H2 + CO). For the FT-Olefin process, an efficient catalyst restricting the product distribution of FTS to light olefins is required. Aligned with this goal, we synthesized 24 catalysts comprising Fe and Cu in combination with rare earth metals (La, Ce, Nd, Ho, Er) and zeolite supports (ultrastable Y and mordenite). FT-Olefin performances of these catalysts were screened using a high-throughput test system at atmospheric pressure, and then promising catalysts were tested under high pressure in a conventional test system. Results show that Nd increases selectivity to light olefins and Ho suppresses C5+ and coke formation. It is also demonstrated that zeolite-metal interaction, leading to a mixture of both acidic and basic sites, is significant in increasing light olefin production. The mordenite-supported 20 wt % Fe, 0.5 wt % Cu, and 0.5 wt % Ho catalyst provides the highest light olefin yield with the lowest coke and heavier hydrocarbon selectivity.


  • Open Access

    Effect of promoter type and synthesis method on catalytic performance of Fe-Mn based FT-olefin catalysts

    by Gamze Gümüşlü Gür, Özge Ati̇k

    Direct production of light olefins, building blocks of chemical industry, can be attained by developing efficient catalysts for Fischer?Tropsch synthesis (FTS). The nature of FTS complicates the catalyst development process as the product distribution is affected by the components and the preparation methods of the catalyst. In this work, high-throughput (HT) methodology is employed to overcome this problem by testing many different catalyst formulations. Fast performance screening of 40 different α-Al2O3 supported Fe-Mn based catalysts promoted with Cu, K and Ni, using different impregnation agents, was performed in a HT test system at atmospheric pressure. Promising catalyst candidates identified by HT analysis were further subjected to high pressure FTS in a conventional system. Results indicate that coupled with Mn, Ni promoted CH4 production, Cu increased CO conversion, K enhanced olefin selectivity and olefin-to-paraffin ratio. In double promotion of Cu and K, Cu balanced the activity and stability loss due to K, while K enhanced olefin selectivity. n-pentane aided impregnation slightly enhanced catalytic performance. Differences observed in catalytic performance were regarded as related to the structural changes caused by promoter and impregnation type based on characterization data obtained by H2-TPR, XRD, SEM, EDS mapping and N2 adsorption.