Xing Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xing Xie has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bin Li
School of Engineering Anhui Agricultural University Hefei China
3 shared publications - Dongjing Liu
School of Energy and Power Engineering Jiangsu University Zhenjiang China
3 shared publications - Dan Lin
School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013, China
2 shared publications - Chaoen Li
School of Civil and Transportation Engineering, Ningbo University of Technology, Ningbo, China
1 shared publication - Christian Fabrice Magoua Mbeugang
School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Faisal Mahmood
Department of Energy Systems Engineering, University of Agriculture, Faisalabad 38000, Pakistan
1 shared publication
Latest Publications
- Open Access
Understanding the Synthesis of Turbostratic/Flash Graphene via Joule Heating
The introduction of the Joule heating (JH) method for synthesizing turbostratic graphene has attracted considerable attention from researchers due to its promising potential for commercialization compared to earlier techniques. Numerous studies have outlined the technology’s basic operation and how parameters such as electric field, operating time, and temperature influence the quality and type of graphene produced. Despite this, there is still a lack of concise and comprehensive studies that exclusively focus on the JH method with turbostratic graphene as the target product. This review article is a facile attempt to provide the scientific community with an overview of the historical development and operational principles of Joule heating. It also discusses the structural and fundamental differences between turbostratic and conventional graphene, along with methodologies for characterizing turbostratic graphene. Furthermore, the synthesis mechanisms of turbostratic graphene via JH are analyzed, and the future perspectives for advancing this method are also presented.
Open AccessUnderstanding the Synthesis of Turbostratic/Flash Graphene via Joule Heating
The introduction of the Joule heating (JH) method for synthesizing turbostratic graphene has attracted considerable attention from researchers due to its promising potential for commercialization compared to earlier techniques. Numerous studies have outlined the technology’s basic operation and how parameters such as electric field, operating time, and temperature influence the quality and type of graphene produced. Despite this, there is still a lack of concise and comprehensive studies that exclusively focus on the JH method with turbostratic graphene as the target product. This review article is a facile attempt to provide the scientific community with an overview of the historical development and operational principles of Joule heating. It also discusses the structural and fundamental differences between turbostratic and conventional graphene, along with methodologies for characterizing turbostratic graphene. Furthermore, the synthesis mechanisms of turbostratic graphene via JH are analyzed, and the future perspectives for advancing this method are also presented.
- Open Access
- 6 February 2024
- Published by MDPI AG in Separations
- Vol. 11 (2) , 48
CO2 Adsorption by Bamboo Biochars Obtained via a Salt-Assisted Pyrolysis Route
Recently, salt-assisted pyrolyzation has been deemed an emerging and efficient method for the preparation of biochars due to its facile operation as well as its good structural and chemical properties. In this work, biochars (MBCx) are prepared by heating bamboo powders in eutectic salts (Li2CO3 + K2CO3) at 500–600 °C in the air. Multiple technologies are employed to examine the physiochemical properties of bamboo biochars. Correlations between heating temperature and structural features and carbon dioxide uptakes of bamboo biochars have been investigated. The results show that heating temperature has a significant influence on the physicochemical properties of bamboo biochars. With the elevation of the heating temperature, the defect structures of bamboo biochars gradually ascend, especially when the heating temperature reaches 600 °C. MBCx biochars visibly exceed conventional bamboo biochar prepared via pyrolyzation in a nitrogen stream free of salt addition. Pyrolysis of bamboo in eutectic salts endows biochars with higher oxygen content and more carbon defects, which likely accounts for their better CO2 capture activities.
- 6 February 2024
- Published by MDPI AG in Separations
- Vol. 11 (2) , 48
Open AccessCO2 Adsorption by Bamboo Biochars Obtained via a Salt-Assisted Pyrolysis Route
Recently, salt-assisted pyrolyzation has been deemed an emerging and efficient method for the preparation of biochars due to its facile operation as well as its good structural and chemical properties. In this work, biochars (MBCx) are prepared by heating bamboo powders in eutectic salts (Li2CO3 + K2CO3) at 500–600 °C in the air. Multiple technologies are employed to examine the physiochemical properties of bamboo biochars. Correlations between heating temperature and structural features and carbon dioxide uptakes of bamboo biochars have been investigated. The results show that heating temperature has a significant influence on the physicochemical properties of bamboo biochars. With the elevation of the heating temperature, the defect structures of bamboo biochars gradually ascend, especially when the heating temperature reaches 600 °C. MBCx biochars visibly exceed conventional bamboo biochar prepared via pyrolyzation in a nitrogen stream free of salt addition. Pyrolysis of bamboo in eutectic salts endows biochars with higher oxygen content and more carbon defects, which likely accounts for their better CO2 capture activities.
- Open Access
Effect of Biomass Particle Size on the Torrefaction Characteristics in a Fixed-Bed Reactor
The aim of this study is to investigate the influence of biomass particle size on the torrefaction characteristics under different torrefaction temperatures and times. Paulownia wood with particle sizes ranging from 12 to 2 produced. However, at higher temperatures, decarbonylation reactions were significantly strengthened with more CO generated. The contents of CO2 and CO could account for more than 98 vol% of the product gas. The influence of particle size on the chemical composition of the solid product was much smaller than that of torrefaction temperature and time, but the energy yield of the solid product decreased with the decrease in particle size. The increase in torrefaction temperature and time could significantly increase the C content in the solid product while reducing its O content. It is recommended to use a relatively higher temperature (e.g., 290 °C) for the torrefaction of large particle biomass, as it could significantly reduce the impact of particle size on the torrefaction process and reduce the torrefaction time.
Open AccessEffect of Biomass Particle Size on the Torrefaction Characteristics in a Fixed-Bed Reactor
The aim of this study is to investigate the influence of biomass particle size on the torrefaction characteristics under different torrefaction temperatures and times. Paulownia wood with particle sizes ranging from 12 to 2 produced. However, at higher temperatures, decarbonylation reactions were significantly strengthened with more CO generated. The contents of CO2 and CO could account for more than 98 vol% of the product gas. The influence of particle size on the chemical composition of the solid product was much smaller than that of torrefaction temperature and time, but the energy yield of the solid product decreased with the decrease in particle size. The increase in torrefaction temperature and time could significantly increase the C content in the solid product while reducing its O content. It is recommended to use a relatively higher temperature (e.g., 290 °C) for the torrefaction of large particle biomass, as it could significantly reduce the impact of particle size on the torrefaction process and reduce the torrefaction time.