Dan Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dan Lin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bin Li
School of Engineering Anhui Agricultural University Hefei China
3 shared publications - Dongjing Liu
School of Energy and Power Engineering Jiangsu University Zhenjiang China
3 shared publications - Xing Xie
School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013, China
2 shared publications - Chaoen Li
School of Civil and Transportation Engineering, Ningbo University of Technology, Ningbo, China
1 shared publication - Christian Fabrice Magoua Mbeugang
School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Faisal Mahmood
Department of Energy Systems Engineering, University of Agriculture, Faisalabad 38000, Pakistan
1 shared publication
Latest Publications
- Open Access
Understanding the Synthesis of Turbostratic/Flash Graphene via Joule Heating
The introduction of the Joule heating (JH) method for synthesizing turbostratic graphene has attracted considerable attention from researchers due to its promising potential for commercialization compared to earlier techniques. Numerous studies have outlined the technology’s basic operation and how parameters such as electric field, operating time, and temperature influence the quality and type of graphene produced. Despite this, there is still a lack of concise and comprehensive studies that exclusively focus on the JH method with turbostratic graphene as the target product. This review article is a facile attempt to provide the scientific community with an overview of the historical development and operational principles of Joule heating. It also discusses the structural and fundamental differences between turbostratic and conventional graphene, along with methodologies for characterizing turbostratic graphene. Furthermore, the synthesis mechanisms of turbostratic graphene via JH are analyzed, and the future perspectives for advancing this method are also presented.
Open AccessUnderstanding the Synthesis of Turbostratic/Flash Graphene via Joule Heating
The introduction of the Joule heating (JH) method for synthesizing turbostratic graphene has attracted considerable attention from researchers due to its promising potential for commercialization compared to earlier techniques. Numerous studies have outlined the technology’s basic operation and how parameters such as electric field, operating time, and temperature influence the quality and type of graphene produced. Despite this, there is still a lack of concise and comprehensive studies that exclusively focus on the JH method with turbostratic graphene as the target product. This review article is a facile attempt to provide the scientific community with an overview of the historical development and operational principles of Joule heating. It also discusses the structural and fundamental differences between turbostratic and conventional graphene, along with methodologies for characterizing turbostratic graphene. Furthermore, the synthesis mechanisms of turbostratic graphene via JH are analyzed, and the future perspectives for advancing this method are also presented.
- Open Access
Oxidative Pyrolysis of Typical Volatile Model Compounds Under Low Oxygen Equivalence Ratios During Oxidative Pyrolysis of Biomass
This study aims to investigate the oxidative pyrolysis of biomass volatiles with a particular focus on the formation of liquid products. Furfural, hydroxyacetone, and 3,4-dimethoxybenzaldehyde were chosen as volatile model compounds. The impacts of the oxygen equivalence ratio (ER, 0–15%) and temperature (400–500 °C) on the product composition and distribution were examined using a two-stage quartz-tube reactor. The results showed that volatile pyrolysis was limited at the lower temperature of 400 °C even with oxygen introduction, while it could be significantly promoted at 500 °C as illustrated by the observed great decrease in the GC-MS peak areas of the volatile compounds especially under an oxidative atmosphere. For instance, the peak area of 3,4-dimethoxybenzaldehyde at 500 °C under an ER of 4% was only ~9% of that at 400 °C. Oxygen introduction enhanced the volatile decomposition with the formation of mainly permanent gases (although not given in the study) rather than liquid products, but distinct impacts were obtained for varied volatile compounds possibly due to their different chemical structures and autoignition temperatures. From the perspective of liquid product formation, furfural would undergo the cleavage of C-C/C-O bonds to form linear intermediates and subsequent aromatization to generate aromatics (benzene and benzofuran). The presence of oxygen could enhance the oxidative destruction of the C-C/C-O bonds and the removal of O from the molecules to form simple aromatics such as benzene, phenol, and toluene. Hydroxyacetone mainly underwent C-C/C-O cleavage that was further enhanced in the presence of oxygen; the resultant intermediates would recombine to generate acetoin and 2,3-pentanedione. A higher ER would directly oxidize the alcoholic hydroxyl group (-OH) into an aldehyde group (-CHO) to form methyl glyoxal, while 3,4-dimethoxybenzaldehyde mainly underwent cleavage and recombination of bonds connected with the benzene ring including aldehyde group (-CHO), CAr-O, CMethoxy-O bonds, thus forming 1,2-dimethoxybenzene, toluene, and 3-hydroxybenzadehyde. This study provides more fundamental insights into the homogeneous oxidation of volatiles during the oxidative fast pyrolysis of biomass, facilitating the deployment of this technology.
Open AccessOxidative Pyrolysis of Typical Volatile Model Compounds Under Low Oxygen Equivalence Ratios During Oxidative Pyrolysis of Biomass
This study aims to investigate the oxidative pyrolysis of biomass volatiles with a particular focus on the formation of liquid products. Furfural, hydroxyacetone, and 3,4-dimethoxybenzaldehyde were chosen as volatile model compounds. The impacts of the oxygen equivalence ratio (ER, 0–15%) and temperature (400–500 °C) on the product composition and distribution were examined using a two-stage quartz-tube reactor. The results showed that volatile pyrolysis was limited at the lower temperature of 400 °C even with oxygen introduction, while it could be significantly promoted at 500 °C as illustrated by the observed great decrease in the GC-MS peak areas of the volatile compounds especially under an oxidative atmosphere. For instance, the peak area of 3,4-dimethoxybenzaldehyde at 500 °C under an ER of 4% was only ~9% of that at 400 °C. Oxygen introduction enhanced the volatile decomposition with the formation of mainly permanent gases (although not given in the study) rather than liquid products, but distinct impacts were obtained for varied volatile compounds possibly due to their different chemical structures and autoignition temperatures. From the perspective of liquid product formation, furfural would undergo the cleavage of C-C/C-O bonds to form linear intermediates and subsequent aromatization to generate aromatics (benzene and benzofuran). The presence of oxygen could enhance the oxidative destruction of the C-C/C-O bonds and the removal of O from the molecules to form simple aromatics such as benzene, phenol, and toluene. Hydroxyacetone mainly underwent C-C/C-O cleavage that was further enhanced in the presence of oxygen; the resultant intermediates would recombine to generate acetoin and 2,3-pentanedione. A higher ER would directly oxidize the alcoholic hydroxyl group (-OH) into an aldehyde group (-CHO) to form methyl glyoxal, while 3,4-dimethoxybenzaldehyde mainly underwent cleavage and recombination of bonds connected with the benzene ring including aldehyde group (-CHO), CAr-O, CMethoxy-O bonds, thus forming 1,2-dimethoxybenzene, toluene, and 3-hydroxybenzadehyde. This study provides more fundamental insights into the homogeneous oxidation of volatiles during the oxidative fast pyrolysis of biomass, facilitating the deployment of this technology.
- Open Access
- 6 February 2024
- Published by MDPI AG in Separations
- Vol. 11 (2) , 48
CO2 Adsorption by Bamboo Biochars Obtained via a Salt-Assisted Pyrolysis Route
Recently, salt-assisted pyrolyzation has been deemed an emerging and efficient method for the preparation of biochars due to its facile operation as well as its good structural and chemical properties. In this work, biochars (MBCx) are prepared by heating bamboo powders in eutectic salts (Li2CO3 + K2CO3) at 500–600 °C in the air. Multiple technologies are employed to examine the physiochemical properties of bamboo biochars. Correlations between heating temperature and structural features and carbon dioxide uptakes of bamboo biochars have been investigated. The results show that heating temperature has a significant influence on the physicochemical properties of bamboo biochars. With the elevation of the heating temperature, the defect structures of bamboo biochars gradually ascend, especially when the heating temperature reaches 600 °C. MBCx biochars visibly exceed conventional bamboo biochar prepared via pyrolyzation in a nitrogen stream free of salt addition. Pyrolysis of bamboo in eutectic salts endows biochars with higher oxygen content and more carbon defects, which likely accounts for their better CO2 capture activities.
- 6 February 2024
- Published by MDPI AG in Separations
- Vol. 11 (2) , 48
Open AccessCO2 Adsorption by Bamboo Biochars Obtained via a Salt-Assisted Pyrolysis Route
Recently, salt-assisted pyrolyzation has been deemed an emerging and efficient method for the preparation of biochars due to its facile operation as well as its good structural and chemical properties. In this work, biochars (MBCx) are prepared by heating bamboo powders in eutectic salts (Li2CO3 + K2CO3) at 500–600 °C in the air. Multiple technologies are employed to examine the physiochemical properties of bamboo biochars. Correlations between heating temperature and structural features and carbon dioxide uptakes of bamboo biochars have been investigated. The results show that heating temperature has a significant influence on the physicochemical properties of bamboo biochars. With the elevation of the heating temperature, the defect structures of bamboo biochars gradually ascend, especially when the heating temperature reaches 600 °C. MBCx biochars visibly exceed conventional bamboo biochar prepared via pyrolyzation in a nitrogen stream free of salt addition. Pyrolysis of bamboo in eutectic salts endows biochars with higher oxygen content and more carbon defects, which likely accounts for their better CO2 capture activities.