ASAlexander Spens

Alexander Spens

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alexander Spens has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Simplified Injection Model for Variable Area Turbine Fluidic Throttling

    by Alexander Spens, Evan J. McFadden, Cole D. Westrick, Jeffrey P. Bons

    Previous studies have demonstrated the effectiveness of using fluidic actuators to throttle the flow through a nozzle guide vane, enabling a variable area turbine (VAT) with no moving parts. A simplified model was developed to assess the driving design factors that influence the blocked flow fraction and throttling effectiveness of the actuators. The model approximates slot injection using a simplified stream tube analysis, neglecting mixing with the primary passage flow. Throttling performance is predicted for fluidic actuators with different widths, orientations, streamwise locations, and pressure ratios. This simplified model evaluates these actuators in a constant width straight duct and a variable width duct. Two-dimensional CFD of injection in the nozzle guide vane passage reported strong agreement with the results of the simple model using the variable width duct. Higher injection pressure ratios result in more injected mass flow but not significantly higher throttling effectiveness. Wider slots retain the effectiveness and block much more primary flow. Upstream oriented injection proves best for both effectiveness and blockage capabilities. Finally, there is an optimal injection location relative to the passage throat, which is extracted by both the model and CFD. This model has potential application for optimizing fluidic VAT throttling designs while saving on the cost of high-fidelity testing and production of these configurations.


  • Characterization of Out-of-Plane Curved Fluidic Oscillators

    by Alexander Spens, Patrick J. Brandt, Jeffrey P. Bons

    A novel fluidic oscillator design, in which the oscillator is curved along the primary flow direction, was evaluated. The effects of mass flow rate, hydraulic diameter, aspect ratio, curvature radius, surface roughness, inlet orientation, and nonconstant curvatures were experimentally investigated. Measurements of the oscillation Strouhal number, discharge coefficient, spreading angle, and sweeping angle were used to characterize the jet. The resulting oscillators were found to fall into one of three categories: oscillated at the same frequency and sweep angle as conventional flat oscillators; oscillated at a slightly higher frequency and lower sweep angle than flat oscillators; or no dominant oscillation frequency detected and with no sweeping action. An unsteady Reynolds-averaged Navier–Stokes computational fluid dynamics simulation revealed fundamental differences in the internal flow mechanisms between flat and curved oscillators that drive the sweeping jet. The curvature between 37.5 and 62.5% of the total length, or the region from the inlet nozzle to halfway through the main chamber, was a primary factor influencing the response type of a design. Due to the curvature of these oscillators, they have the ability to be used in geometrically constrained spaces, such as the leading edge of wings and turbine vanes.


  • Active Fluidic Control of a Nozzle Guide Vane Throat

    by Alexander Spens, Jeffrey P. Bons

    Experiments were conducted to validate the building blocks of a fluidically controlled variable area turbine concept that uses injected high-pressure air to effectively reduce the choke area of the turbine inlet. Preliminary results from a simple quasi-1D converging-diverging nozzle, with an injection flow slot upstream of the throat, showed a 2.2:1 ratio between throttled mass flowrate and injected mass flowrate at a constant nozzle pressure ratio. The penetration of the injection flow and corresponding reduction in the primary flow streamtube were successfully visualized using a shadowgraph technique. Building on this success, a representative single passage nozzle guide vane transonic flowpath was constructed to demonstrate feasibility beyond the quasi-1D converging-diverging nozzle. Both secondary slot blowing from the vane pressure surface and vane suction surface just upstream of the passage throat again successfully reduced primary flow. In addition, fluidic vortex generators were used on the adjacent suction surface to reduce total pressure loss and further throttle the primary flow. Implications for the application of this active flow control technology to a variable area turbine are considered.


  • Leading-Edge Active Flow Control Enabled by Curved Fluidic Oscillators

    by Alexander Spens, Anthony P. Pisano, Jeffrey P. Bons

    A new design of fluidic oscillator, in which the oscillator is curved along its primary flow direction, allows for a sweeping jet to be placed near the leading edge of a wing as an active flow control device. Previous studies of fluidic oscillator applications have shown their promise as an active flow control device by increasing the lift over a wing and preventing flow separation. However, the planar extent of the flat fluidic oscillators creates challenges when trying to optimally implement them in a confined geometry. The application of these new curved oscillators is experimentally investigated on the leading edge of an upswept NACA0018 airfoil full-span wing. Global load cell measurements of lift, drag, and pitching moment are presented and analyzed using suction surface static pressure taps, and particle image velocimetry data are presented. The effects of active flow control on lift, drag, and stall at a Reynolds number of 100,000 are documented for a variety of oscillator chordwise locations near the leading edge and compared to traditional vortex-generating jets. While further aft-positioned oscillators produced a larger increase in maximum lift, more forward locations resulted in better poststall performance and delayed flow separation over the wing.