Alok Ranjan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alok Ranjan has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Arindam Majumder
National Institute of Technology Agartala
3 shared publications - Sagnik Pal
National Institute of Technology Agartala
3 shared publications Madhujit Deb
National Institute of Technology Agartala
2 shared publications- Madhujit Deb
Department of Mechanical Engineering, National Institute of Technology Agartala, Agartala, India
2 shared publications - Ranjan Das
Department of Mechanical Engineering, Indian Institute of Technology Ropar, Rupnagar, India
2 shared publications - Debabrata Barik
Department of Mechanical Engineering, Karpagam Academy of Higher Education, Coimbatore, India
1 shared publication
Latest Publications
- 27 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (3) , 1372-1384
Performance analysis of porous-based taper-shaped fin for enhanced heat transfer rate using cuckoo search algorithm
This paper deals with the thermal and fluid flow behavior of porous and non-porous fins. Initially, a solid heat sink with circular fins is analyzed and validated. Further work is done making circular tapered porous fin of the same volume and height as of uniform circular fin. The geometrical parameters are porosity (Ø = 0.1–0.92), pore diameter ( d p ), fiber diameter ( d f ), radius ratio ( R *), and pores per inch (PPI = 10). Four different cases viz., case I ( R * = 1.2), case II ( R * = 1.5), case III ( R * = 2), and case IV ( R * = 4) of taper porous fins are considered in a computational domain with Reynolds number ( Re ) ranging 400–1900 (based upon channel inlet parameter) and air as working fluid. The Forchheimer–Brinkman extended Darcy model is considered to characterize the flow in porous media. The value of Nusselt number ( Nu ), friction factor ( f ), and thermal performance factor (TPF) is evaluated. Results reveal that, for case I at Ø = 0.92 and PPI = 10, the value of Nu and TPF is approximately 63% and 159% higher than solid circular fin at Re = 1876.11. For case IV, the reduction in pressure drop is approximately 21.15% compared to solid circular fin at Re = 1876.11. For optimum Nu , a cuckoo search optimization is evaluated using the response surface method. Upon examination, the optimum Nu is obtained at the combination of R * = 1.2, Ø = 0.92, and Re = 1876.11, which got validated against the numerical work with 0.15% accuracy.
- 27 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (3) , 1372-1384
Performance analysis of porous-based taper-shaped fin for enhanced heat transfer rate using cuckoo search algorithm
This paper deals with the thermal and fluid flow behavior of porous and non-porous fins. Initially, a solid heat sink with circular fins is analyzed and validated. Further work is done making circular tapered porous fin of the same volume and height as of uniform circular fin. The geometrical parameters are porosity (Ø = 0.1–0.92), pore diameter ( d p ), fiber diameter ( d f ), radius ratio ( R *), and pores per inch (PPI = 10). Four different cases viz., case I ( R * = 1.2), case II ( R * = 1.5), case III ( R * = 2), and case IV ( R * = 4) of taper porous fins are considered in a computational domain with Reynolds number ( Re ) ranging 400–1900 (based upon channel inlet parameter) and air as working fluid. The Forchheimer–Brinkman extended Darcy model is considered to characterize the flow in porous media. The value of Nusselt number ( Nu ), friction factor ( f ), and thermal performance factor (TPF) is evaluated. Results reveal that, for case I at Ø = 0.92 and PPI = 10, the value of Nu and TPF is approximately 63% and 159% higher than solid circular fin at Re = 1876.11. For case IV, the reduction in pressure drop is approximately 21.15% compared to solid circular fin at Re = 1876.11. For optimum Nu , a cuckoo search optimization is evaluated using the response surface method. Upon examination, the optimum Nu is obtained at the combination of R * = 1.2, Ø = 0.92, and Re = 1876.11, which got validated against the numerical work with 0.15% accuracy.
- Open Access
- 3 February 2023
- Published by Wiley in International Journal of Energy Research
- Vol. 2023, 1-20
Numerical and Optimization-Based Study on Split Hemispherical Shaped Fins for Augmenting Heat Transfer Rate
This paper deals with the numerical investigation of split hemispherical fins mounted staggered over a base plate. The thermal and flow analyses have been carried out to evaluate the Nusselt number (Nu), pressure drop , and hydrothermal performance factor (HTPF) with air as a medium and Reynolds number ( to 15000). The cylindrical fin (CF) and hemispherical fin (HF, of radius ) of the same volume and height have been formed and placed in the computational domain. Results reveal that the Nu for CF compared to HF is 1.3-1.4 times higher, with approximately 1.5 times higher for the given Re range. The value of HTPF for HF is greater than unity (/1.13-1.20) for all the considered Re values. Secondly, the HF gets split into longitudinal and transverse flow directions for better solid-fluid interaction. The geometrical parameters are transverse offset TO (/= ), longitudinal offset LO (/= ), and Re. Results show that the highest value of Nu (/=384.10) and HTPF (/=1.33) have been obtained at (at LO =0) and (at ) for the highest Re (/=15000). At last, the cuckoo search algorithm (CSA) coupled with the response surface method (RSM) has been performed to fetch the optimum value of Nu based upon dimensionless TO, dimensionless LO, and Re. The optimum value (obtained at , , and ) of Nu (=/392.16) from CSA is promising, with the numerically obtained Nu value (=/384.1059) with an error of 2.05%.
- 3 February 2023
- Published by Wiley in International Journal of Energy Research
- Vol. 2023, 1-20
Open AccessNumerical and Optimization-Based Study on Split Hemispherical Shaped Fins for Augmenting Heat Transfer Rate
This paper deals with the numerical investigation of split hemispherical fins mounted staggered over a base plate. The thermal and flow analyses have been carried out to evaluate the Nusselt number (Nu), pressure drop , and hydrothermal performance factor (HTPF) with air as a medium and Reynolds number ( to 15000). The cylindrical fin (CF) and hemispherical fin (HF, of radius ) of the same volume and height have been formed and placed in the computational domain. Results reveal that the Nu for CF compared to HF is 1.3-1.4 times higher, with approximately 1.5 times higher for the given Re range. The value of HTPF for HF is greater than unity (/1.13-1.20) for all the considered Re values. Secondly, the HF gets split into longitudinal and transverse flow directions for better solid-fluid interaction. The geometrical parameters are transverse offset TO (/= ), longitudinal offset LO (/= ), and Re. Results show that the highest value of Nu (/=384.10) and HTPF (/=1.33) have been obtained at (at LO =0) and (at ) for the highest Re (/=15000). At last, the cuckoo search algorithm (CSA) coupled with the response surface method (RSM) has been performed to fetch the optimum value of Nu based upon dimensionless TO, dimensionless LO, and Re. The optimum value (obtained at , , and ) of Nu (=/392.16) from CSA is promising, with the numerically obtained Nu value (=/384.1059) with an error of 2.05%.
- 21 September 2022
- Published by Springer Nature
- p. 115-126
Performance Analysis of Split Circular and Drop-Form Fin Geometry for Enhanced Heat Transfer Rate
- 21 September 2022
- Published by Springer Nature
- p. 115-126
Performance Analysis of Split Circular and Drop-Form Fin Geometry for Enhanced Heat Transfer Rate
- 21 April 2021
- Published by Wiley in Journal of Heat Transfer
- Vol. 143 (6)
Use of Cuckoo Search Algorithm for Performance Evaluation of Split Elliptic Shaped Fins for Enhanced Rate of Heat Transfer
Proper dissipation of thermal energy has always been a need for desirable efficiency of a system. Extended surface aids in releasing the heat to the immediate surrounding by inducing an extra area. This particular work assesses thermal and fluid flow behavior of extended surfaces with circular and elliptic shaped cross section. Extended surfaces of unvaried cross section are mounted over a square plate arrayed in a staggered manner. With the aid of different thermofluidic parameters, the elliptic shaped pin fin is established to provide a higher thermal performance enhancement of nearly 15% over cylindrical pin fin at inlet flow velocity of 2.35 m/s. Further, for elevating the interaction between the surface of the fin and the fluid, elliptic fins are reoriented to form a split. In contrast to cylindrical shaped fin, modification using split shows better result with the highest heat transfer increment of nearly 25%. Further, in order to maximize Nusselt number (Nu), a single objective cuckoo search optimization analysis is done by adopting the response surface method. After analyzing the optimization, it is found that the maximum value of Nu is obtained at dimensionless transverse offset (TO*) = 0.125 and dimensionless longitudinal offset (LO*) = 0, which has been further validated with the numerical result within 0.97% accuracy. Further, for the cylindrical fin, the present simulations agree with the available empirical correlation within 6.22% accuracy.
- 21 April 2021
- Published by Wiley in Journal of Heat Transfer
- Vol. 143 (6)
Use of Cuckoo Search Algorithm for Performance Evaluation of Split Elliptic Shaped Fins for Enhanced Rate of Heat Transfer
Proper dissipation of thermal energy has always been a need for desirable efficiency of a system. Extended surface aids in releasing the heat to the immediate surrounding by inducing an extra area. This particular work assesses thermal and fluid flow behavior of extended surfaces with circular and elliptic shaped cross section. Extended surfaces of unvaried cross section are mounted over a square plate arrayed in a staggered manner. With the aid of different thermofluidic parameters, the elliptic shaped pin fin is established to provide a higher thermal performance enhancement of nearly 15% over cylindrical pin fin at inlet flow velocity of 2.35 m/s. Further, for elevating the interaction between the surface of the fin and the fluid, elliptic fins are reoriented to form a split. In contrast to cylindrical shaped fin, modification using split shows better result with the highest heat transfer increment of nearly 25%. Further, in order to maximize Nusselt number (Nu), a single objective cuckoo search optimization analysis is done by adopting the response surface method. After analyzing the optimization, it is found that the maximum value of Nu is obtained at dimensionless transverse offset (TO*) = 0.125 and dimensionless longitudinal offset (LO*) = 0, which has been further validated with the numerical result within 0.97% accuracy. Further, for the cylindrical fin, the present simulations agree with the available empirical correlation within 6.22% accuracy.
- 17 January 2020
- Published by Springer Nature
- p. 857-867
Performance Analysis of Split-Drop-Shaped Pin Fins for Improved Heat Transfer Rate
- 17 January 2020
- Published by Springer Nature
- p. 857-867
Performance Analysis of Split-Drop-Shaped Pin Fins for Improved Heat Transfer Rate