Shijin Nie
Shijin Nie has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Guiping Lin
Laboratory of Fundamental Science on Ergonomics and Environmental Control, School of Aeronautic Science and Engineering
3 shared publicationsLizhan Bai
Laboratory of Fundamental Science on Ergonomics and Environmental Control, School of Aeronautic Science and Engineering
3 shared publicationsHongxiang Lan
Laboratory of Fundamental Science on Ergonomics and Environmental Control, School of Aeronautic Science and Engineering
2 shared publicationsKang Yuan
Department of Engineering Mechanics, Key Laboratory for Thermal Science and Power Engineering of Ministry of Education
2 shared publicationsShuai Su
Laboratory of Fundamental Science on Ergonomics and Environmental Control, School of Aeronautic Science and Engineering
2 shared publications- Xinyi Li
China Three Gorges University
2 shared publications
Latest Publications
- 27 August 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
High-Thermal-Conductivity Radiative Cooling Films for Enhanced Passive Daytime Cooling
Passive daytime radiative cooling (PDRC) technology relies on reflecting solar visible light that carries high energy and radiating surface heat to a low-temperature cold background in the long-wave infrared band, thereby achieving clean energy-saving cooling. However, the irreversibility of high flux heat flow is often present in practical applications, resulting in the inability to maximize the cooling effect produced by radiative cooling. In this study, we developed an integrated radiative cooling (RC) film with high thermal conductivity for efficient cooling (DPHA film) by strategically constructing internal thermal channels within the RC interface. Compared to the indoor chamber temperature, the DPHA film, with its superior optical properties (reflectivity ∼ 0.96, emissivity ∼ 0.98), yielded a maximum temperature difference of 17.5 °C and an average difference of 13.2 °C under solar intensity of 977 W m-2. The cooling effect was 8.5 °C lower than commercially available highly reflective aluminum paint and 5.2 °C lower than a comparable cooler. Thermal conductivity tests showed that the DPHA film possessed high out-plane thermal conductivity (0.755 W m-1 K-1), which facilitated the radiative dissipation of surface heat via forming a thermal gradient with the environment. After 30 days of continuous strong UV irradiation experiments, the obtained film showed favorable optical properties and aging resistance. DPHA film as a new radiative cooler effectively improves the overall performance of the cooling, with good potential and scalability for outdoor applications. This provides a new way to develop radiative cooling materials that are efficient, cost-effective and easy to mass produce.
- 27 August 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
High-Thermal-Conductivity Radiative Cooling Films for Enhanced Passive Daytime Cooling
Passive daytime radiative cooling (PDRC) technology relies on reflecting solar visible light that carries high energy and radiating surface heat to a low-temperature cold background in the long-wave infrared band, thereby achieving clean energy-saving cooling. However, the irreversibility of high flux heat flow is often present in practical applications, resulting in the inability to maximize the cooling effect produced by radiative cooling. In this study, we developed an integrated radiative cooling (RC) film with high thermal conductivity for efficient cooling (DPHA film) by strategically constructing internal thermal channels within the RC interface. Compared to the indoor chamber temperature, the DPHA film, with its superior optical properties (reflectivity ∼ 0.96, emissivity ∼ 0.98), yielded a maximum temperature difference of 17.5 °C and an average difference of 13.2 °C under solar intensity of 977 W m-2. The cooling effect was 8.5 °C lower than commercially available highly reflective aluminum paint and 5.2 °C lower than a comparable cooler. Thermal conductivity tests showed that the DPHA film possessed high out-plane thermal conductivity (0.755 W m-1 K-1), which facilitated the radiative dissipation of surface heat via forming a thermal gradient with the environment. After 30 days of continuous strong UV irradiation experiments, the obtained film showed favorable optical properties and aging resistance. DPHA film as a new radiative cooler effectively improves the overall performance of the cooling, with good potential and scalability for outdoor applications. This provides a new way to develop radiative cooling materials that are efficient, cost-effective and easy to mass produce.
- 25 June 2025
- Published by American Chemical Society (ACS) in Langmuir
Design of Impermeability and Durability for Superhydrophobic Mortar
The ubiquitous use of mortar in construction is compromised by its susceptibility to environmental degradation, including water penetration, abrasion, and UV radiation, which significantly reduce its service life. To address these challenges, a new type of superhydrophobic mortar with a water contact angle of 155° and a sliding angle of 8° (SC-4) was fabricated by using the method of propriety hydrophobic modification. The compressive strength (CS) of SC-4 was 29.83 ± 1.2 MPa, and the flexural strength (FS) was 5.47 ± 0.3 MPa at the age of 28 days, showing balanced mechanical properties. Compared to the ordinary mortar (OC) group, SC-4 maintained competitive interfacial wettability. Notably, despite 25% lower compressive strength than the benchmark, SC-4 exhibited enhanced structural stability through optimized integration. Leaching tests validated its outstanding impermeability with significantly reduced cumulative water and NaCl absorption. After 200 abrasion cycles, it maintained superhydrophobicity and minimal mechanical property variation, while UV aging tests showed only marginal strength degradation, confirming robust resistance to environmental stressors. This study highlights SC-4's superior impermeability and durability, offering a practical solution for mortar applications.
- 25 June 2025
- Published by American Chemical Society (ACS) in Langmuir
Design of Impermeability and Durability for Superhydrophobic Mortar
The ubiquitous use of mortar in construction is compromised by its susceptibility to environmental degradation, including water penetration, abrasion, and UV radiation, which significantly reduce its service life. To address these challenges, a new type of superhydrophobic mortar with a water contact angle of 155° and a sliding angle of 8° (SC-4) was fabricated by using the method of propriety hydrophobic modification. The compressive strength (CS) of SC-4 was 29.83 ± 1.2 MPa, and the flexural strength (FS) was 5.47 ± 0.3 MPa at the age of 28 days, showing balanced mechanical properties. Compared to the ordinary mortar (OC) group, SC-4 maintained competitive interfacial wettability. Notably, despite 25% lower compressive strength than the benchmark, SC-4 exhibited enhanced structural stability through optimized integration. Leaching tests validated its outstanding impermeability with significantly reduced cumulative water and NaCl absorption. After 200 abrasion cycles, it maintained superhydrophobicity and minimal mechanical property variation, while UV aging tests showed only marginal strength degradation, confirming robust resistance to environmental stressors. This study highlights SC-4's superior impermeability and durability, offering a practical solution for mortar applications.
- 3 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (19) , 25498-25510
Experimental Study on Energy-Free Superhydrophobic Radiative Cooling Versatile Film with Enhanced Environmental Tolerance
Clean, energy-free methods of cooling are an effective way to respond to the global energy crisis. To date, cooling materials using passive daytime radiative cooling (RC) technology have been applied in the fields of energy-efficient buildings, solar photovoltaic cooling, and insulating textiles. However, RC materials frequently suffer from comprehensive damage to their microstructure, resulting in the loss of their initial cooling effect in complex outdoor environments. Here, a superhydrophobic daytime passive RC porous film with environmental tolerance (SRCP film) was fabricated, which integrated strong solar reflectivity (approximately 90%), mid-infrared emissivity (approximately 0.97), and superhydrophobicity (water contact angle (WCA) of 160° and sliding angle of 3°). This study revealed that SRCP film had an average reflectivity of 14.3% higher than SiO2 particles in the 0.3-2.5 μm wavelength region, achieving a cooling effect of 13.2 °C in ambient conditions with a solar irradiance of 946 W·m-2 and a relative humidity of 74% due to the synergistic effect of effective solar reflection and thermal infrared emission. In addition, empirical results showed that the attained films possessed outstanding environmental tolerance, maintaining high WCA (156°), stable cooling effect (8.3 °C), and low SiO2 loss (less than 5.1%) after 30 consecutive days of UV irradiation and 14 days of corrosion with acidic and alkaline solutions. More importantly, this work could be flexibly prepared by various methods without the use of any fluorine-containing reagents, which greatly widens the practical application scope.
- 3 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (19) , 25498-25510
Experimental Study on Energy-Free Superhydrophobic Radiative Cooling Versatile Film with Enhanced Environmental Tolerance
Clean, energy-free methods of cooling are an effective way to respond to the global energy crisis. To date, cooling materials using passive daytime radiative cooling (RC) technology have been applied in the fields of energy-efficient buildings, solar photovoltaic cooling, and insulating textiles. However, RC materials frequently suffer from comprehensive damage to their microstructure, resulting in the loss of their initial cooling effect in complex outdoor environments. Here, a superhydrophobic daytime passive RC porous film with environmental tolerance (SRCP film) was fabricated, which integrated strong solar reflectivity (approximately 90%), mid-infrared emissivity (approximately 0.97), and superhydrophobicity (water contact angle (WCA) of 160° and sliding angle of 3°). This study revealed that SRCP film had an average reflectivity of 14.3% higher than SiO2 particles in the 0.3-2.5 μm wavelength region, achieving a cooling effect of 13.2 °C in ambient conditions with a solar irradiance of 946 W·m-2 and a relative humidity of 74% due to the synergistic effect of effective solar reflection and thermal infrared emission. In addition, empirical results showed that the attained films possessed outstanding environmental tolerance, maintaining high WCA (156°), stable cooling effect (8.3 °C), and low SiO2 loss (less than 5.1%) after 30 consecutive days of UV irradiation and 14 days of corrosion with acidic and alkaline solutions. More importantly, this work could be flexibly prepared by various methods without the use of any fluorine-containing reagents, which greatly widens the practical application scope.
- 7 February 2023
- Published by Elsevier in Materials Letters
- Vol. 339
Study of salt resistance and mechanical strength of robust and non-fluorinated superhydrophobic cement
- 7 February 2023
- Published by Elsevier in Materials Letters
- Vol. 339
Study of salt resistance and mechanical strength of robust and non-fluorinated superhydrophobic cement