Ali Turan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ali Turan has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Seta Bogosyan
Univ Alaska, Dept Elect & Comp Engn, Fairbanks, AK 99775 USA
3 shared publications - Metin Gokasan
Istanbul Technical University
2 shared publications - Metin Gokasan
Istanbul Technical University, Electrical and Electronics Eng. Faculty, Maslak, Istanbul, Turkey.. tr
1 shared publication - Richard W. Wies
University of Alaska Fairbanks
1 shared publication - Trivikram Singaraju
University of Alaska Fairbanks, Electrical & Computer Engineering Department Duckering Building, Fairbanks, AK 99775, USA
1 shared publication
Latest Publications
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2984-2989
Development of Remotely Accessible Matlab/Simulink Based Electrical Drive Experiments
This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namely permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namele permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2984-2989
Development of Remotely Accessible Matlab/Simulink Based Electrical Drive Experiments
This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namely permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namele permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 5426-5432
Hardware-in-the-loop simulation of PUMA 560 via internet
This study introduces a remotely accessible hardware-in-the-loop simulator (HILS), which is used for the development of the PUMA 560 dynamics and control. The HILS setup aims to give on-site and remote students/researchers the capability to experiment with any robotic configuration and control algorithm of their choice, without the need for the physical existence of the equipment in the laboratory. To increase the flexibility offered by the system, the HILS setup is made a part of the UAF RemoteLab facility, with the developed client/server communication, which gives remote access to all Matlab/Simulink based applications. As an implementation example, in this study, the HILS setup is used to develop dynamics and PD+ control of PUMA 560 as a graduate project. Experimental results and animations are also presented
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 5426-5432
Hardware-in-the-loop simulation of PUMA 560 via internet
This study introduces a remotely accessible hardware-in-the-loop simulator (HILS), which is used for the development of the PUMA 560 dynamics and control. The HILS setup aims to give on-site and remote students/researchers the capability to experiment with any robotic configuration and control algorithm of their choice, without the need for the physical existence of the equipment in the laboratory. To increase the flexibility offered by the system, the HILS setup is made a part of the UAF RemoteLab facility, with the developed client/server communication, which gives remote access to all Matlab/Simulink based applications. As an implementation example, in this study, the HILS setup is used to develop dynamics and PD+ control of PUMA 560 as a graduate project. Experimental results and animations are also presented
- 1 July 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4 (21635137) , 3201-3206
Development of a Client-Server Communication Method for Matlab/ Simulink Based Remote Robotics Experiments
This paper describes the development of a client-server communication method using the TCP/IP protocol to run Matlab/Simulink compatible motion control units operating on the remote server side. The developed method is currently in use to allow access to a hardware-in-the-loop (HIL) robot simulator developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is used to develop a variety of robot dynamics configurations and control algorithms on the robotic simulator. Practical case study results from a remotely conducted graduate robotics project are also presented in relation to a HIL simulator developed for the real-time simulation of PUMA-type robots. The UAF remote laboratory Web site can be accessed at: http://www.uaf.edu/ece/remote-robotics
- 1 July 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 4 (21635137) , 3201-3206
Development of a Client-Server Communication Method for Matlab/ Simulink Based Remote Robotics Experiments
This paper describes the development of a client-server communication method using the TCP/IP protocol to run Matlab/Simulink compatible motion control units operating on the remote server side. The developed method is currently in use to allow access to a hardware-in-the-loop (HIL) robot simulator developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is used to develop a variety of robot dynamics configurations and control algorithms on the robotic simulator. Practical case study results from a remotely conducted graduate robotics project are also presented in relation to a HIL simulator developed for the real-time simulation of PUMA-type robots. The UAF remote laboratory Web site can be accessed at: http://www.uaf.edu/ece/remote-robotics